Best Jeep Gladiator Tow Bars

I spent five months flat towing my Silverado using this tow bar. I estimate I towed 4,000 miles with it and hooked up and disconnected around 20 times. It has held up very well with no rust or finish issues, which is notable as most of the time my spots were either right on the ocean (within 20 feet of the saltwater) or close to the water. I did rinse frequently and kept the Roadmaster cover on when not in use. Hook ups and disconnects are quick and easy, I suggest using gloves as one time when I raised it up to 90 degrees to snap in to the retainer after unhooking one of the bars was still extended and slid down and pinched my finger pretty good. (This was simply my stupidity, not the fault of the design, but gloves would have helped:) The LED lights on the sides also help make the rig more visible from the side. In my opinion this is the highest quality tow bar currently on the market. eTrailer also did an outstanding job on the entire flat tow installation.

We traveled 7,200 miles last winter pulling your 2023 2 door Jeep Wrangler and it performed Excellent. I did buy the optional cover which I think this is a wise investment to protect it when parked.

This towbar has been very disappointing. When it was time for a new towbar, I decided to downgrade from the Sterling to this Falcon, and that was a big mistake. This towbar cannot be described as "non-binding". Unless your tow vehicle is perfectly aligned with the motorhome and level, there is no chance of releasing the latches - they bind and will not release. If I get stuck in a stopped position where the car is misaligned from the coach by more than about 10 degrees, or higher or lower than the hitch by more than a few inches, I have a major project to release the towbar from the car, even sometimes having to use a punch and hammer to forcibly remove the hitch pins. Further, after just a few months of use, one of the release mechanisms quit working altogether, so I my partner has to start the car and jiggle back and forth in order to find a spot where I can remove the hitch pins. Once the towbar is unhooked, I have to use a screwdriver to dig around under the failed release lever in order to push the cam in manually so I can push the outer arm back in. The guides along the arms for the cables are not useful and dangerous. I initially used straight power and safety cables running through the guides, and they go chewed up in a short period of time. I had to buy new coiled cables that do not run through the guides, and have had no further problem. As a towbar, this device works fine. But it is NOT non-binding, and I highly recommend upgrading to one of the higher-end towbars. This device is too problematic to recommend, and I would never buy it again.

It took me awhile to decide if this would work with the Rough Country bumper I wanted to put on my 2010 Jeep Wrangler. After looking at numerous photos of the bumper I decided to pull the trigger and it worked. The mount cleared the bumper and I’m very pleased with how easy it was to mount and use the tow bar. I did everything myself except wiring the plug on my Jeep.

We've been towing our Jeep Grand Cherokee for about 8 months now with this tow bar and it's worked flawlessly! We've been places where the coach and Jeep are not perfectly aligned putting the attaching pins in a bind, but with a simple release of the handle it would release the arm and unbind the pin. Super easy to use. I highly recommend the Nighthawk All Terrain, Non-Binding tow bar. OH! The LED lights along the arm make it look great too!!

Quick delivery and the tow bar was well packed and configured for my Blue Ox base plate. Thanks

So easy a caveman can do it. Great material quality, etrailer was fast on shipping, and hd support ready if needed. I consider myself an intermediate mechanic sk I had no problems doing this by myself. Instructions were good, I modified to make some install details easier and emergency link better.

We had a towbar failure while on the road. Luckily it failed as we stopped at grocery store and not on the highway. I was able to order a new Blue Ox 10k rated towbar and had it shipped to our next campground. We only had to drive two hours disconnected. RV hitch rated for 8K, SUV is 5400 lbs + contents so a 10K rated towbar and cables gave us piece of mind of being the most robust component of our towing setup.

Arrived quickly and well packaged. Took less than an hour to install on the RV with the included safety cables and wiring.I haven't pulled our Bronco with it yet but the tow bar appears to be well built and a quality product.

First, received the package and upon opening, found that the linch pins were missing. One phone call and issue was resolved and replacement items were being expedited to me. Appears the box came open on one end during shipment and parts came out before carrier retaped the tear. Good on E-Trailer for outstanding and prompt customer service! Now, the Sterling All Terrain towbar - very impressive unit as I had bought this on reputation only as no dealers had any in stock (they say it is too costly to carry in store). Very well made, excellent finish and welds. Instructions are quite clear and easy to follow. I like that when you purchase this unit, it is a “total package”. There is nothing I could see that is cheaply made - all quality. This was my first purchase from E-trailer, and based on how this order went start to finish, and having to deal with missing parts on an order - I am very pleased and will deal with them in the future.

Excellent product. Towing 4 door Jeep Wrangler Sport.

I have towed our Honda Accord Sport over 7000 miles now with this tow bar and have been very happy with it. I didn't spend the extra $'s to upgrade to a non-binding bar and while I have had a couple of problems in getting the bars to release it was infrequent. I would suggest you read the owners literature and be sure to clean and lubricate the towbar regularly. It makes a difference

This is one of the best, two items I purchased of about 6 or 7 items acquired to rig my 2001 GMC YukonXL for flat towing. The 10,000 lb capacity is valued. the tow bar slides work well. the 3/4inch pins are strong and I have had no problems. The tow bar pulls a YukonXL with some extra stuff, fuel and tools and weighs probably 6,500 lbs (my est--haven't put it on a CAT scale). When I rig my 2020 Chev Silverado Trail Boss to flat tow, I expect to be able to use this.

Perfect bar to tow my 2015 Chevy Silverado 1500 Crew Cab. My earlier Falcon is great for my lighter Honda CRV. Thus one is robust and works flawlessly for my Silverado. eTrailer came through again as usual.

On the road in our RV when I discovered our 3yr 7mo Blue Ox Tow Bar had a failure that I was not going to be able to use again. I call Willian S at etrailer about getting a new Blue Ox Tow Bar and having it shipped to a nearby UPS store. William checked to ensure it would be delivered before our scheduled departure. Not only did he assure me it would meet the timeline but he checked it after shipping to make sure it got here. Also he checked about a “like new” tow bar which saved me ~$500. Thanks for keeping me on the road without delay!

We made the best choice of recommendations when we purchased the Blue Ox Ascent tow bar for our Buick and Winnebago Tour Coach. The setup and hook-up are consistently easy to perform, and it takes us less than 10 minutes to be ready to tow our car. This is a great way to have your cake and eat it, too! LOL!!

While the quality of this units seems excellent, and it is a good price, I was unable to use it in my setup. I Bought it to go with the Blue Ox base plate for a 2014 Chevy Spark. That base plate sets the tow bar connections 23" above the ground. This tow bar requires a 7" rise from the base plate connection to the hitch. Meaning 30" above the ground at the hitch. In my rig, this would require a hitch riser of over 12". I have no complaints about the tow bar, however, it is not a good option with the 2014 Spark Blue Ox base plate.

Towed a 4 door Rubicon with Dodge 2500 truck. The tow bar did great on the 2000+ mile trip. The bar is very easy to couple and uncouple.

Great purchase and suggestion from etrailer. This thing is so easy to hook up to the Jeep and we couldn't be happier. We've only towed a few times, but already the wife has taken over hooking up the tow bar while I hook up the Brake Buddy in the Jeep. Easy to hook up, just as easy to disconnect after you arrive. I wish we had done this years ago!

I thought this tow bar was compatible with etrailer invisible base plate kit with/ removable arms, The tow bar came with only 2 spacer washers, no nuts for 2 bolts and pins to go through. The attachment pins to the base plates are too big. this puts me in a bad way, I guess I will have to purchase new for myself ........... thanks

The adjustable arms make this tow bar simple to hook up and disconnect. I can pull up behind our RV and hook up in about 3 minuets (including the wiring for our break buddy and putting the transfer in neutral). Disconnecting and stowing the bar is even faster. Although is tow bar is locked to the baseplate and folds flat it is so easy to remove I end up taking it off and putting it in the back when we will not be towing.

I was slightly nervous that this would be difficult to take on and off if I wasn't on flat ground. So for I have not had any issues and I really like that it hooks up to a 2 inch ball. My jeep has a lift on it and getting things level was easy with and adjustable height mount.

Great product! Works great and support to pick the right tow pbar from George at etrailer was excellent too!

Towed my Ram 2500 loaded with a RZR on a bed rack for thousands of miles. Zero issues

I ordered this tow bar and D ring adapters specifically for my Bronco and it’s way to sloppy and I can’t use this to tow my Bronco

Great Base plate kit! Very easy to follow instructions even with my aftermarket bumper with winch. It fit perfect. The only issue I have is where the safety cables attach to the base plate….the cable connectors are too big to fit through the holes because the Jeep’s frame blocks part of the hole. See photo with red circle. I will have to get a smaller connector.

Very rugged tow bar. You will need this cover: Roadmaster Tow Bar Cover Item # RM-055-3 because the arms don't lock in the short position so they just slide out to the extended lock position when stowed without a cover.

I'm not sure there could be anything better for the tow bar to do. I love the ease of hooking and unhooking in less then 2 min. and the cable holder for the light hookup cable and air hookup so they can't drag on the ground. The release levers work great for taking the tension off the bars to unhook and the storage of the tow bar on the back of the RV works great. All and All I could be happier

etrailer has been just what I need it as a first time tower of a Rv tow car there experience and courtesy of helping someone with no experience has been a huge relief with something so important there help was invaluable all the way through Thank you so much

Very easy to use and handled as well as I expected.

I have purchased other items from etrailer and as usual the delivery is easy to follow and produce as advertised.

Arrived on time and as ordered.

I decided to use an antique Blue Ox tow bar to pull my Mini Cooper behind our RV on a trip to Panama City beach last year. Big Mistake! If it looks questionable, don't use it. When we arrived I was extremely thankful that the Mini was still with us. The old Blue Ox bar was coming apart. I looked locally for a replacement and found one at Camping World and was shocked at the price. eTrailer had the exact same unit for hundreds and hundreds less. And they shipped it quickly right to the camp ground. The Roadmaster Falcon 2 tow bar is very easy to us and mated right up to the Blue Ox kit on the Mini. Thanks eTrailer! We will definitely buy from you again!

Even after I complained to you that I had been -- falsely -- told you do not supply a Blue Ox base plate for Malibus and bought a Roadmaster, you send me a Roadmaster tow bar with some other brand's connectors. I will shortly send you a photograph of the base plate connection I have and expect you to send connections that match it.

The wiring kit for the tow base kit was very well engineered and works very well. The videos for installing the base plate we're awesome step by step process and was very easily accomplished by someone with just a wrench and a drill and a few tools.

Outstanding product and even better customer service! Two backyard mechanics installed baseplate and braking system with just one call to confirm proper wire connection. Total package works great.

1st tow bar I had to send back, due to chip powder coating. 2nd two bar came a week later Great job etrailer. It was easy to do a return and get a replacement. etrailers whole team was great getting me what I wanted. I replaced a 10-year-old tow bar and wanted to replace it with their new XHD you can tell its LBS is higher than my old tow bar.

The tow bar looks good. However, it was missing the large bolts to hold the blue ox adapters onto the tow bar. The hardware kit was not complete. Also, the instructions on attaching the blue ox adapters were NOT CLEAR at all. I think the bar will be very good once I get the missing parts shipped to me.

First, this bar is extremely heavy, which makes transporting and maneuvering cumbersome and difficult. Secondly, I had issues with this unit from the get-go. I did not receive the correct bolts to attach the Roadmaster clevis to the arm ends. The instructions clearly state that a clevis bolt was to be installed with the XHD unit, but it was not in the hardware bag. I had to call customer service (which was so/so, almost like the person didn't believe me) and had the bolts sent to me. I received the bolts but long story short, they were too short. They did not come out of the bottom of the locknut and any attempt to torque them to the point they did protrude, caused the forks of the clevis to bend, which is too much stress on such an important piece. I did not feel it was safe to either have the bolts not protrude, or force them to protrude. Then came the days-long process of trying to rectify the situation. I called customer service and attempted to explain the problem to the rep. She didn't really want to hear my problem and I was quickly rushed off the phone and directed to call Roadmaster for support, which I did. Roadmaster, of course, has nothing to do with this bar, or problem (pictures were sent to RM) and I was directed to call eTrailer back. I spoke to another person and she was a little more helpful. However, during our "conversation," I could hardly get a word in (I was spoken over and interrupted constantly.) I was told that #1.) the first person I talked to had no idea what she was talking about #2.) Demco manufactures these parts, not Roadmaster, #3.) Essentially the correct length bolts don't exist in the parts catalog. At this point I am starting to get upset with my experience and just wanted a tow bar that worked. I was convinced to but a Roadmaster branded tow bar to avoid any more issues (Blackhawk All Terrain) which I found to be strange, I figured the margin on the eTrailer branded products would be higher, but I digress. Since there is no exchange program with eTrailer, I had to purchase the Blackhawk outright. I was given a UPS label to send the XHD back, but I had to wait to receive the Blackhawk to reuse the box, which is not a huge deal, a minor inconvenience at this point. As of today (4/26/24) I am still waiting for a refund on this unit which I was assured it would be on it's way once the tracking number showed that it was picked up by UPS, but this is not the case. In conclusion, the XHD seemed like it would be a decent product if they can get the hardware right (at least for the Roadmaster system) it's just heavier than most tow bars I have had experience with. eTrailer.com customer service can also use some work, I was not happy with the service after the sale I received. Oh, and the final kick in the tail, the Blackhawk does not come with safety cables. If this were my company, I would have thrown those in for the inconvenience, but I was offered nothing for the trouble this has caused, no discount on the Blackhawk, cables or anything. I will do all I can to avoid buying from etrailer again and will direct others to the same.

It’s well put together and easy to install .