Most Popular Leveling Jack for GMC Sierra 2500

Great product and Trailer has great customer service. It's to bad that the shipping companies do not take better care with the items during shipping! will receive replacement parts to fix what was broken, but it causes lots of extra work for the customer. will have to take complete jack off to replace the broken motor cover because of shipping carelessness!! regards, Dan Ewert

Click to Enlarge

This little rig has teeth! Much faster than i expected. About a 30 minute installation from old lift removal to new and wiring. Super simple. Great addition to my hangar 18!

Click to Enlarge

Click to Enlarge

The system is not what was advertised, it's better, at least for me. Everything arrived on a pallet in excellent condition, except for the advertised remote. I contacted etrailer and they put a replacement on order which I received a few days later. In the meantime, I tried to place the controller in the mode to sync the remote and see if the remote I had with my RV would sync, but I could not get the controller in that mode to accept a remote. Upon reading the controller label, I noticed it said BT and had a passcode on the side of it, so I downloaded the app and it connected to my phone. It seems the LCI Linc remote is obsolete for my Ground Control 3.0 and it is now using the phone app. Everything seems to work as expected; I'm excited to try everything out this weekend on our first outing. I was able to push a fiberglass push stick from the front basement to where the rear jacks are located without dropping the underbelly and pull all the required cables to the rear of the camper and utilize existing frame holes to bring the connectors out to the rear jacks. I think this will be a nice upgrade to our fifth wheel after our factory landing gear failed.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

shipped in a timely manner. Easy install wit good instructions. I did have one question about the location of the rear lifts and called the company and we had an answer instantly. Wiring was very easy with good instructions. The system worked on the first try and have had no issues so far. Great system. I was looking at newer campers with auto leveling and about 40 to $50,ooo if I traded my paid for camper in. The cost saved me a lot of money and works as it should and saves my back and a lot of set up time. would and have recommended to others. Thanks.

Let me say this to start, this system is AWESOME!! If you do not have a leveling system on your camper, this one works very , very well. I will say, the install and the learning curve takes time and is not too hard, but it's not super easy either. Once I got the system in place, and understood how to use it, the rest was a piece of cake. Take your time on the install and get help. The parts are robust and heavy, so two people make it much easier. Have sharp drill bits to drill the attachment holes. Wiring is super simple, but take your time and make sure you get all the connections good and tight and secured well with zip ties. The system requires a good strong battery, so make sure your battery is in great shape and you will not have any issues. Get the Lippert app also, it is very helpful. I love it now, when I pull my 2006 Keystone Raptor 5th wheel toy hauler into a campsite, I hit a couple buttons and the longest it has taken to level my unit is 2 minutes and 30 seconds. I love it! It puts the camper at the same level every single time, which is awesome. No guessing, no driving up and down on blocks, just push a button and walk away until the camper is perfect. Would I do this over again you ask? Absolutely. Awesome system!

Click to Enlarge

Click to Enlarge

After the initial installation there was a little confusion about setup I have been very happy with the way it works really simple push one button hit auto levels it's still working well thanks

We love our one touch jack system. We used in on a 3 month camping trip out west setting up probably 40 plus times and we continue to use our camper and the jacks work great!

This has definitely been one of the greatest additions to our Stryker travel trailer. Order was received a day earlier than expected and all in good condition. Installation for myself and two other guys was a slight bit time consuming (due to my wanting all the wires hidden in the underbelly of the trailer). Watching the system level my trailer, with a touch of a single button, impresses me still today a year later. Great purchase and I would definitely recommend this product.

I was amazed at how quickly my replacement from etrailer arrived. I was a bit worried that the installation of my new jack would be more difficult that I expected. The reverse proved to be the case, it was very simple to place the trailer tongue on jack stands, remove the old jack and install the new one. As the old saying goes "even a cave man could do it."

Click to Enlarge

Awesome product. My back thanks you. Very easy to install. Only thing I would change is the speed of the motor. A bit slow but still better than hand cranking.

Click to Enlarge

Click to Enlarge

Wowzers, what having two motors working to lift my 5th wheel toy hauler. Lifts it with no problem. Fast, makes hooking up and unhooking a breeze. No more struggling like it would with the stock single motor setup. Wish I would have done this years ago, not when one of my legs gears stripped on the first day of a 5 day NASCAR weekend. Good thing I had a 6 ton bottle jack, several wood blocks, got it off my truck, enjoyed the weekend and ordered these first thing when I got home. Install wasn't bad, if you work on things, should be no problem. Mild modification of my trailer hangers and flooring in the storage where the legs are, but nothing major. Hooked up to my truck to take the weight off instead of using jack stands. About 6 hours total, took my time to do it right.

I bought this to replace the under powered OEM landing gear on my 2018 39' toy hauler 5th wheel. I received great service from etrailer staff. First time for me to remove and replace landing gear so after 1 or 2 youtube videos I was able to get it done with a little grinding and drilling (and cursing). I've been using the new landing gear for a year now and here are my thoughts: PROS: Ability to adjust the 2 sides independently. Makes leveling much easier. Quality hardware and stronger motors. CONS: The toggle switches that come with it are very stiff and a bit awkward to use. The pin at the bottom of each leg is not attached. You have to pull it out, then line it up with the hole to replace it. All others I've seen have a spring loaded guided pin. The legs don't go up or down any faster than the OEM. Although that was never claimed, I was hoping they would. Overall I am happy with the product. I will say, if I had to do it again I would strongly consider going with the competitor's product for the better controls and spring loaded pins.

Click to Enlarge

Click to Enlarge

The item was value priced compared to the competition so when it was on backorder from the manufacturer for 3 weeks I understood. When I placed my order with the seller I only paid for standard shipping but as soon as the item was received in the seller's warehouse it was shipped UPS next day (a $48 value). I suppose they elected the next day option to compensate for the 3 week manufacturer backorder delay. The item was received as described by the seller and I installed the item the next day. I rated this Excellent.

Click to Enlarge

Did come with switch and circuit breake. I will keep for spare. No instructions of any kind and link on item does not exist. There was a link to a manual jack when I first looked. Simple enough to install without them. Did find color code and wiring diagram. Arrived within 3 days and only slight damage to 69 lb box. Still don’t clearly see how it will level unless RV is already mostly level. One motor, a split screw and assembly floats left/right in the top mounted track. Even though the legs can compensate for uneven ground at the lift, it will just elevate the RV as the same level as where it started. It doesn’t autolevel. Only took 5 minutes to bolt up as I temporarily wired and used the switch to raise into position. Running the wire and installing the electrical was more involved.

Click to Enlarge

Click to Enlarge

I'm typically not one to complain or write a poor review however, E-Trailer has produced very poor customer service and product handling. I called and ordered this landing gear over the phone to ensure with a representative that I was getting the correct part. My concern was the weld stops mounting up to my current brackets. The representative ensured they would fit after reviewing specs. When the legs arrived I was surprised by how poor the packaging was upon opening the makeshift packaging the legs looked like they were used and they were missing several parts. I contacted customer service they offered a $[XX] discount and part replacement. When I went to install the legs, I discovered that they would not fit my brackets and the measurements the representative gave we not accurate. I called customer service again. The end result was I had to purchase another set of legs and wait up to 14 days to get reimbursed for the legs which were the wrong fit. I requested a discount of some sort due to the inconvenience this caused. The supervisor offered expedited shipping and that is all. If I wasn't in a situation in which I needed new legs to repair my 5th wheel, I would have definitely gave my business to another company.

Just what I needed, fast shipping, great product.

I purchased this landing gear a while back for my 25' gooseneck trailer that I haul heavy equipment with. The trailer originally had only a single 10,000lb single speed drop leg jack and was not a very stable setup. The old jack just wasnt cutting it and I needed a more heavy duty set up that I could depend on. I mounted this landing gear and it was one of the best improvements I have made to the trailer. Instead of the old single setup mounted between the neck beams that was very hard to crank under load, the tandem set now provides stable load support across the front and is very easy to crank in low range under load. One feature I liked about this landing gear was they dont have drop legs. The sand shoes are a fixed mount with large pins and wide shoes. Same as those on semi trailers. The lack of a drop leg is no problem as I keep a couple of 6"x6" blocks in the trailer and slide them under the shoes before I jack the trailer up. The blocks give added lift to the jacks and also keep the shoes out of the dirt. These jacks are geared a little higher in high range than smaller jacks so in the time it would take to pull a drop leg and crank down I can have the blocks set up and jacks cranked down. Once the load is felt just switch to low and cranking is effortless. Keep the shoes and legs clean/maintained and they will never rot/fai/bend like the drop legs on smaller capacity jacks. Last thing is I would recommend is to remove the two speed gearbox cover and pack it full of grease before the first use. Two speed boxes come from the factory with very little grease. Intial packing will help prevent excessive break in wear. There are grease fittings on both jacks which can be topped off a couple times a year there after. I wanted a very heavy duty landing gear set that would out last the trailer and one that was rated for more than the trailer will hold. This set has exceeded my expectations.

I was extremely impressed with the recent technical and customer support from etrailer. Over the weekend, they answered my questions to select the appropriate replacement electric jack for my Airstream. Also, when there was a shipping delay (not etrailer’s fault), Rose provided prompt responses and professional support. I will continue to use etrailer for my RV needs.

Click to Enlarge

Works flawlessly. Maybe the only thing I could complain about is it is slower than I think it could be. Along with the side lights could always be brighter. Works great, install kit is awesome, and it works without a stutter.

The bull dog electric tongue jack is awesome. I got it in white to match my trailer. I unbolted the old jack and bolted on the new one in about 5 minutes. (I had my coreless impact gun.) Total install time was about an hour mainly because I wired the jack to my battery inside the trailer that runs the electronic winch and I had to run a separate ground from the battery to one of the mounting bolts for the jack with a cut off switch. So far it works great but time will tell. I'll be using it a lot more next year.

Click to Enlarge

Excellent customer service and followthru by etrailer. Jack is well built and easy to install and use. Would definitely add a flat washer under the bolts to prevent the lock washers from getting drawn into the oblong bolt holes when torquing them done.

Click to Enlarge

Click to Enlarge

This jack was the perfect solution for my application. I have a new enclosed trailer that came with a manual crank and only a tiny battery to run the lights. I did not want the expense of having to buy and cable up a larger battery to just support the tongue jack. Took me 5 minutes to install this new jack using the three bolts that were already on my OEM jack. Now I just back up my truck, plug in the 7-way, and I'm able to move the tongue up and down as needed. Great!

Click to Enlarge

Click to Enlarge

I love my new electric trailer jack ! It has a 7 pin RV plug which makes it so convenient to power. There are lights on both sides to shine onto the hitch after dark. There is a bubble level on top to know when the camper is at least level enough to start setting up. It all works great !

Click to Enlarge

Easy installation, reasonable price, works great! Much to my surprise, our trailer had a 2.25" top hole and a 2" bottom hole. This jack fit fine. The lights are helpful.

Click to Enlarge

I recieved the jack in a timely fashion and the box was destroyed (packing wasn't good) and was a bit worried but it didn't have a scratch on it and was very easy to install. Bolted right up!I really am happy with it and I would recommend it and etrailer!!

Click to Enlarge

Pros: Works better than I anticipated. Looks great and has better ground clearance than the stock scissor-jack stabilizers. Cons: Installation instructions/documentation weak or non-existent. If all of the instructions, wiring diagrams and documentation were in one place on the web page under a separate tab rather than having to dig through the reviews and the Q & A’s, I would have given this a 5 star rating. I ordered the LCI Power Stabilizer Jacks with the white switch Kit (LC369774) because I wanted the switches mounted in the camper wall so they would be better protected than if they were mounted in the flimsy fender skirts of my camper. I also needed the bolt-on spacer kit (LC673594) for both the front and rear jacks to clear a propane line that runs along the length of the frame. Installation was relatively easy, although there are NO instructions on how to install the spacers kits; the video on etrailer.com was no help whatsoever with the installation. I bolted the jack mount brackets to the shorter side of the spacers using carriage bolts and flange nuts; the slotted holes in the spacers accepted the carriage bolts, aligned perfectly with the holes in the jack mounts, and allowed me to install them without having to try to fit a wrench inside. Then it was just a matter of drilling holes in the frame at the appropriate spacing for flange bolts/nuts through the slotted holes on the end of spacers. I was very pleased with how the switches and the switch compartments looked once installed. Again, though, it took lots of digging to find the wiring diagram and then the matrix for the switch wire colors, because the wires on the white switch are colored differently than the black switch that all of the diagrams show. Also, it states on the jack installation instruction sheet that the power must be a minimum of 10 gauge wire (AWG-10), but nowhere on the wiring diagram does it say anything about that. AWG-10 is a MUST because of the way current drops over a distance. In the case of my camper, it is a 30 foot run which requires that gauge of wire for 20 AMPs.

This stabilizer works very well. I replaced the original Lippert unit on my 2008 5th wheel as the parts I needed were no longer available. The original Lippert unit worked great until some idiot in a drunken stupor decided to move it with the stabilizer in the “down” position. I probably won’t do that again anytime soon. DOH!!!

Jack works very well. Not fast but gets the job done. Unfortunately I can't lower my tailgate fully without hitting the jack. Tried to rotate the head as I saw some jacks allowed. This one won't allow that. Very satisfied otherwise. Used less than one full season so can't offer an opinion on durability.

Mounted quick and easy. Plenty of wire for electrical hook up. Lots of power even with a full load of water in the front tank. The only change I made to installation was longer bolts to accept washers and nuts to the bottom side of hitch. I didn't trust the taped holes in the thin hitch frame. This was no fault of the new jack. Still working strong. A back saver that's worth the money. I should have bought one years ago!

Click to Enlarge

Item arrived a day earlier & in good condition! & was a very easy install ,& is a upgrade from manual one that broke at the handle ,& this is a upgrade for my 2008 22'Airstream Safari! Can't wait for my next outing, Also I like that it comes with a backup manual hand crank in case you need it,& that it was a exact fit for my travel trailer,It's a complete package that needs nothing else.

Click to Enlarge

I purchased this jack to replace my tired 10 year old camper jack . I ordered it at 10:00 AM Monday and as promised by Ian it was at my doorstep on Friday just in time for my weekend getaway . Installation was a breeze . I gave the product a 4 out of 5 for a few reasons . First , I was not able to see the manufacturer of the jack before receiving it . Which made name brand comparison pricing difficult . However I feel pricing was on target . Second , I feel that the jack should come with a battery terminal end connector and new mounting bolts with the hardware that was included . This didn’t pose any difficulty to me as I had hardware at hand but for some it will mean a trip or two to the hardware store . Third , once installed , at least with my truck and trailer , unless the truck and trailer are perfectly aligned and level the jack motor gets in the way of opening the tail gate . On first use I noticed it was much slower than my original but the strength made up for it . This jack had no difficulty or hesitation lifting my truck and trailer for load distribution and anti sway bar installation . I would recommend etrailer and this product . Time will be the final test of its durability .

Click to Enlarge

Click to Enlarge

I've had this power jack for about a year and it works flawlessly, it beats hand cranking. And not to mention the great service from etrailer their the best in the business.

Click to Enlarge

Bought Pro Series Weight Dist Hitch, Jameson C was very helpful picking the right one out , ordered it on Friday and it arrived on Wednesday a day earlier than expected. Placed a second order for an electric jack and misc. parts. Extremely happy with their service. I don't review stuff but these guys deserve one.

Click to Enlarge

Click to Enlarge