# 1
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
To be honest, I use it upside down. I needed a hitch with rise, but none were available at time of purchase, and yours, inverted, works perfectly! The welds are regularly checked and remain all secure. It's a good hitch.
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
# 2
Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-3/4" Long - 3,500 lbs
The welding splatter found its way to the hitch pin hole and it took me some time with a Dremel to clean it out so the hitch pin would slide in.
Each edge of the hitch receiver shipping carton was pierced by mounting brackets, but no damage fortunately. Consider adding another layer of cardboard padding?
# 3
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.
I searched the internet to put a hitch on my 2016 Chevy Equinox and found an instructional video from eTrailer.com where they installed on my exact car. I decided to go with eTrailer.com because they answered all my questions and because of the video-I support businesses that go the extra mile with these videos. Shipping was quick and well tracked, however, the box was flimsy and the one end of the hitch had come out of the box side and the ball mount could have easily come out of that hole during shipping. If I were eTrailer.com I'd charge an extra couple of bucks for more sturdy boxes-people will still buy as eTrailer is a well-trusted brand and this would overcome a lot of the negative reviews you'll see on their site about this shipping issue in their own reviews :-) I installed the hitch by myself (definitely recommend help as two people holding it up to the frame makes attaching 100% easier) in about 45 minutes total (out of the box, read instructions, review video again and installation complete). All hardware went on with no issues. Great quality hitch! I also bought the lesser expensive wiring assembly because most recent equinox's come hitch ready with pre-wired assembly in the left side compartment-snap and done. Picked up a new trailer at Home Depot within days and drove 5 feet and the clacking was horrible. I had always had a welded hitch before buying a hitch that took a ball mount. I really thought something was wrong and when I searched the internet that night it turns out this is very common. However, all you need is some sort of hitch "silencing" device. The number of options will drive you mad but I went with the Roadmaster Quiet Hitch and it did the trick for much less than most of the other options. If I were eTrailer.com I'd have that as one of the RECOMMENDED add-ons and explanation why its super-worthy when customers are buying a hitch. Would have saved me the time and hassle of dealing with it later and the extra shipping charge for buying after the fact when I got free shipping for the other items the first time :-) All in all, I'm super, super happy with my hitch, wiring assembly, ball mount, ball mount locking pin and the hitch silencer. Buy with confidence from eTrailer.com Paul R., Syracuse, NY
# 4
Draw-Tite Drawbar for 1-1/4" Hitches - 5" Rise - 10" Long - 3,500 lbs
I've got a lowered 1995 VW Jetta with a 1.25" receiver. I had to use a 6" extension along with a long, straight drawbar so any steep incline had me going at an angle and even then I would sometimes scrape. Some one had this drawbar on their Jetta and it looked good. With the measurements provided on this site I determined it would sit far enough away from my bumper and elevate the ball so my trailer wouldn't be angled down so much. Very glad I ordered this unit, it fits the car and works perfectly! Much better than my previous fix.
Great all around except for the fact that the retaining pin is a clip over, as opposed to a push through. That said, I simply safety wired the retaining clip and that took care of it. Very satisfied overall.
# 5
Draw Tite Drawbar for 1-1/4" Hitch - 5/8" Rise, 1-1/4" Drop - 9-3/4" Long - 3.5K
Every Item I have ordered from etrailer.com has been top of the line . Easy ordering , prompt service , and excellent installment instructions . I watch the video , more than once , and follow the expert's direction . I wouldnt order trailer parts anywhere else . Thank You
I believe my choice, with the help of etrailer, of this Draw-Tite trailer hitch receiver, along with a few other items to go with it, such as the drawbar, hitch ball and wiring harness, was a good one for my 2017 Subaru Forester. I also have to compliment etrailer for their excellent video on how to install it. All together, it really made the purchase very easy and smooth. Thanks etrailer.
# 6
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
The hitch and ball mount are excellent quality. My concerns are twofold. The hitch is so heavy that I had to take it to my mechanic to have it installed. Minor cost and inconvenience, but the hitch for my previous F-150 was just as sturdy, but easy to install myself (albeit with higher ground clearance). My concern about the ball mount is that the factory told me erroneously that it could not be reversed for a drop, so I returned it. This order is for the replacement after I was finally correctly told it could be reversed and how to do that. Ball mount would have been a 3 for that reason, and overall hitch and ball mount quality a 5. So I averaged them.
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
# 7
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
We sold our small motor home and purchased a small travel trailer. This hitch provided a perfect solution to how to use our bike rack while towing the trailer. It even allows room for the pickup tailgate to be lowered without removing the bikes from the rack. The hitch is very hefty with a high weight limit - plenty for the GVW of the trailer (7,000#) plus 125# of rack and bikes.
This has been an amazing multipurpose ball mount. We purchased this to use with our Hollywood Bike Rack and also to connect onto our boat. We weren't sure if this would work, but it was awesome. It is very well built and We had to make some minor adjustments to the position of our boat on the trailer so the turning radius of the bike rack that was attached would clear the truck. This is very well made and solid.
# 8
Curt Class III Ball Mount with 2-5/16" Ball - 2" Drop - 7,500 lbs
Everything arrived on time and well packaged. I installed a Curt hitch receiver to go with this ball mount. Installation for the hitch went exactly as described and was fairly simple for even a novice like me. Very pleased with etrailer.com and with Curt brand products in general. Couldn't be happier with the process from beginning to end. And the hitch looks and works great!
etrailer is great! My hitch shipped quickly and was packaged well. Plus customer service has been great keeping me updated and staying in touch with my order.
# 9
MaxxTow Ball Mount w/ 2" Accessory Receiver - 2" Hitches - 2-1/4" Drop - 5,000 lbs
Heavy duty , very good quality.
# 10
Curt Tri-Ball Mount - 3 Chrome Balls - 10,000 lbs
Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.
This item should solve the problem I have had with a stainless 3-way ball when I tried to reverse the position on the ball mount. The threads galled between the hex nut and hitch ball.
# 11
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
We really like the hitch we ordered for our Camry. It was extremely easy to install. Fit perfectly!
Wonderful product. I had the hitch installed in 10 minutes. The wiring was a little more tricky because it required running a power wire all the way to the battery. I towed my trailer from Florida to Tennessee and back. Etrailer is still wonderful to deal with as they always have been in the past. My hitch came in a couple of days. I wouldn't think of ordering from any one else.
# 12
Curt Class II Euro Style Drawbar with 2" Ball - 2-5/8" Rise - 3,500 lbs
My Mini Cooper is lowered and this unit really helped level out the trailer I am pulling. The product is heavy and solid. I would definitely recommend this item
Heavy duty! I was a little bummed when I found out how much more difficult it was to find a half inch pin for this, but no matter. It is a tad loose inside the hitch, so there's a little rattle, but I doubt it's as noticable as I make it seem. Super classy and a welcome change from the typical draw bar style. Goes great with my Volvo V70 T5. Thanks etrailer.com!
# 13
Curt Drawbar for 1-1/4" Hitches - 5-3/8" Rise, 6" Drop - 5-9/16" Long - 2K
I used this on a 2014 Ford Fusion with a Reese receiver hitch made for my vehicle. Either the neck of the drop hitch is not long enough to get the ball a few inches away from the vehicle or the Reese receiver hitch sits too far under the vehicle.
Worked as advertised
# 14
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 2" Rise, 4" Drop - 7.5K
Great purchase experience. eTrailer has this convenient package of ball and hitch already torqued together, AND includes a locking pin in addition to the normal cotter pin! Website is clear on details of package, contents, and dimensions of each component. Shipping was fast and packaged well. I’m not sure if I saved money compared to buying all this separately, but I’m going to believe I did. Thanks!
dodge journey 2014 etrailer service excellent the hitch don't fit perfect with the spare tire other ways is pretty good if you tele out the spare tire you going to have a hard time to put them back etrailer sevicio es excelente la pieza no se acopla perfecto con la rueda de repuesto del resto se monta perfecto . si se retira la rueda de repuesto es muy dificil de poner de vuelta en el compartimento
# 15
Draw-Tite Ball Mount - 6-3/4" Rise, 8" Drop - 10" Long - 5,000 lbs
arrived in excellent condition. Customer service from E-Trailer keep me informed on the delivery status of the hitch drop
Just as advertised and solves my problem of trailer tongue level to hitch position. Delivered on schedule with no hiccups. Fits perfectly in the 2" factory receiver on my Jeep JKU. The 2" ball in the picture is a reused one not new which is why it has rust on it.
# 16
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
High quality ball mount and they arrived at my doorstep within 36 hours of placing my order, how did you do that?
Works as intended - great value.
# 17
Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
Just what I needed, most receivers would not allow me to open the tail gate on my 2022 dodge ram without hitting the trailers crank used to mount and dismount the car hauler trailer, this receiver give me the extra few inches I needed and it works perfectly, I tried many local sources but they all came up too short, etrailer is the place to go for all trailer parts, they seem to know and sell exactly what you may need
For a 7,500 lb hitch, I was surprised it didn’t have a wedge support welded on where the flat iron is welded to the square tube.
What our customers are saying:
"very easy to shop"