# 1
Swagman XC2 Bike Rack for 2 bikes - 1-1/4" and 2" Hitches - Frame Mount
I like the overall design of this rack, but unfortunately after hauling a couple bikes around for a while the point where the crossbar connects has apparently rounded off so the rack swings back and forth. I've used rope to tie the ends of the rack to the car to stop this from getting worse, but it's inconvenient. Note: the hitch connection itself is good and solid, but the point where the crossbar connects to the bar coming from the hitch has gotten loose and there's no way that I can see to tighten it.
It works great! Easy, quick, you know. One needs to screw in the hitch bolt, for some reason, before latching it. Other than that, it makes going bike riding way easier.
# 2
Thule Hitching Post Pro Bike Rack for 4 Bikes - 1-1/4" and 2" Hitches
The good: I like the way the bikes are held in and the ability to add the upright adapters to the bike frame holders. The straps are quality too. For a jeep with a spare tire, this is the perfect length to clear it. This rack is 5 stars from the bike holders to the base of it. The bad: the 2"receiver adapter and bolt are insufficient. I wish they made this in a solid 2" hitch. The entire setup is held into the receiver by a very short bolt. It only goes about half way into the receiver tube. So your hitch is only "secured" on one side. A hitch pin or bolt should go through the receiver tube completely imo so it can be secured on the other end with a retaining clip or nut. Because this only goes in the one side, the entire weight of the rack plus bikes are held tight to one side of the receiver by the undersized bolt and washer. A few bumps down the road and that bolt loosens. Now instead of distibuting the weight of the rack and bikes on the receiver and post, it's completely up to the bolt to keep you from losing the rack. The bolt threads get damaged too. I took this down a dirt road and nearly lost everything. I had to buy my own bolt with hd fender washers and lock washers to correct this. Thule should've provided this from the start. The current short bolt design where only one side of the receiver secures the rack is unacceptable. This rack is 1 star at best for the connection to the receiver.
Hitch pin broke before I got it. Looks like a poor design for the locking pin, they might want to consider a different design. I got a 3/8 shear pin from Home Depot to replace and it works great. Bike rack is great!
# 3
Swagman XTC2 Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
First-time rack buyer / owner / installer. The rack arrived in a timely fashion, maybe a day or 2 ahead of schedule. It was well packaged. I’m LOVING this bike rack. It was easy to put together and to mount on my new Honda Passport. Thus far, no squeaks in my 2” receiver. Hardest part of initial set-up is figuring out the best way to position two bikes. Trial & error and some patience. The directions weren’t clear as to where the 2 left-over screws went. I found the answer in another review and have posted a pic in case others have the same problem (photo with pen pointing at screw). These screws go in the underneath side of both of the folding arms. They appear to keep the wheel wells from sliding off in case in you drive with an empty, un-folded rack, and forgot to tighten down the wheel wells. The folding arm push / pull pins can be difficult at times. I coated the tips with some lube. That and a little jiggling seems to solve that issue. I guess it’s better for the pins to be snug vs popping right out. I added a small Master lock to the hitch pin (in lieu of the provided cotter pin) as a theft deterrent. I read that a 3/16 shackle lock will fit into the bike clamp down arms to also act as a deterrent. I had an old 3/16 lock that did snugly fit and appeared to be locked. HOWEVER, I yanked on the lock and it came open as there isn’t quite enough clearance for the shackle to lock. I discovered that longer 3/16 shackle locks are hard to find. Have attached a photo of the lock that actually fits and works (Ace Hardware). One lock on the upper clamp down arm will secure both arms as the lower arm can’t be removed without removing the upper arm. The clamp down arms appear to be coated to prevent damage to your bike. I’ve tried a simple rag and ultimately settled on pool noodle pieces as a precautionary measure. I CAN NOT open my tailgate (regardless of whether or not the rack is fold up and in the bike carry position). If that’s a concern for you, then spring for the more costly titling version. My back-up camera still functions.
The Swagman XTC-2 platform bike carrier arrived very quickly from etrailer and in good shape, the actual carrier box is inside another shipper box, which I'm sure helped with its condition. Assembly was relatively quick and painless, even though the instructions could be a little more thorough. Installing the carrier on the back of our Jeep Patriot also was quick, it helps to have an extra ratchet & 3/4" socket laying around for just this purpose. Installing the bikes takes a little patience and trial and error the first time you try and put them on the carrier. It's easy enough to adjust the wheel holders to fit the wheelbase of your bikes, but for us at least, the challenge was trying to swing the vertical support bar up into position after putting on the first bike (closest to the Jeep). We couldn't angle the bike enough toward the Jeep to have the bar clear the bike. We learned that the easiest way to secure the first bike was to remove the ratcheting frame hooks altogether, put the bike in the carrier, swing up the vertical support bar, put in the pin, and then slide one of the frame hooks down on the bar. The outside bike is much easier because you can set the bike in the carrier at whatever angle you need, not being limited by the back of the vehicle. One thing we did to protect the bike frames was to use some foam pipe insulation as cushion between the frame hook and the frame (see pictures). Once you get a system for installing the bikes, it is very quick to load/unload them. The rack seems to be well made and doesn't wiggle excessively when traveling. All in all a good product for a good price, would definitely recommend it for anyone looking for a platform bike carrier.
# 4
Yakima OnRamp Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
This is a great product and works beautifully! The only issue was some sloppily made plastic turn knobs that were cross threaded on arrival. However, Yakima immediately shipped out replacements. It carries two large E bikes easily. They fasten solidly and are easy to load and unload!
etrailer: prompt delivery, fair price! Rack: It does fit my (2) Gazelle T10 eBikes. 1) I found I had to adjust every setting to get bikes to fit. Until you learn there are many adjustments, it does not seem like the center/vertical clamps will reach both seat posts. 2) The ramp is barely usable; my wheels are max it will fit and you must have at least 12ft of clearance on each side of car to get bike lined up with ramp. 3) My bikes have a "walk" feature, this is not usable as its too awkward to hold the walk button down and move around the rack. I found its easier to abandon the ramp and load front then rear wheel. I will rig up a wheel stop, on ends of each wheel holder so bike will not roll off while I strap it in. 4) Rack did NOT come with a lock for hitch pin; this is very disappointing as they say in manual this is an optional item. Every rack I have seen at least has a clip that would otherwise hold the hitch pin in if somehow the bolt loosened up. 5) The rack weight is the lightest I have found. 6) You must load the first bike (closest to car) from car passenger side. This will avoid you bike pedals hitting the vertical bar. That means you must load the 2nd bike manually as there is no way to get the pedals past the vertical bar. I will get used to this, I hope. 7) The rack is a few inches above the receiver (part that goes into hitch) so if you have a low hitch this might be an issue with ground clearance. With both bikes mounted up, it seems very stable and hopefully will be secure in travel.
# 5
Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
This bike rack works great for our 2 Lectric 2.0 e-bikes. We mount it on our 2019 Honda Ridgeline. It folds up nicely when it’s on the truck and we are using our bikes. The locking mechanisms work well also. I contacted support for a smaller hook arm to clamp B over the bike frame. They knew exactly what I needed and shipped it - no problem.
I've been using this bike rack alongside a trailer hitch I got here for my small car (chevy bolt ev) and it was exactly what I was looking to get to haul around my fat tire mountain bike bike. Sometimes I throw two bikes on there (either an e-bike, slightly heavier at 60 lbs, or a 2nd mountain bike) and it's perfect.
# 6
Yakima FrontLoader Wheel Mount Bike Carrier - Roof Mount
Overall I am happy with these bike carriers. They mount to the racks over the bed of my Tundra TRD Pro. Installation is simple. I think they could be just a bit sturdier because there is just a bit of wobbling when driving on bumpy roads but I'm not too worried about them coming dislodged. Take note that although they come with a cable lock to attach the bike to the carrier, the key is sold separately.
Very good product. It holds the bike securely on the roof without contacting the frame. It is easy to adjust from my road bike to my 29er mountain bike. Our drives are all relatively short, so I like that I do not need to remove the front wheel to lock in the bike. It's also nice that the SKS locking system allows me to use the same key for this rack that I use for my Yakima roof box and hitch rack. This is my first roof rack and I chose this route for a couple reasons. Some of the roads we travel to get to our trail heads are a bit rough and with a roof rack I don't have to worry about bottoming out a hitch rack hanging off the back of the vehicle. Also, it takes up less room in the garage. Our vehicle is a 2000 Jeep Grand Cherokee with an additional 4 inches of ground clearance. That makes it a bit of a reach for my 5'4" wife, so we take our two-step along to help her. This is my third time purchasing from etrailer, and each experience has been very good. They are a very customer service oriented company. I really appreciate all the additional information they provide on their products, especially all the videos they produce to aid in reviews, assembly, and use.
# 7
Thule T2 Pro XTR Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
Great product, great company to do business with. etrailer is the best. Friendly, helpful and they made sure the bike rack was shipped immediately and it was delivered on time.
The quality of the rack is very sturdy and well built. I needed a rack that has a 12” spacing between wheels do to the baskets on each bike, and this rack delivered that. The issues I have with this rack are: I have a GMC Yukon suv and with the rack mounted I have to lift my two Lecritc 2.0 e-bikes, at 60 pounds each up over 24” to get it mounted. It sure could use ramps, which I know it did not come with. The clamp hold down does not work with fenders on a bike. It does not clamp very well on the cross bar (male and female) type do to the width and the angle of the cross bars. When clamping in front of the front fender makes the bike very unstable, and will require additional strapping and tie downs to secure the bikes. It claims it is for e-bikes, but only if it has no fenders. Nice rack, just not for me.
# 8
Softride Shuttle Pad Tailgate Pad for Full-Size Trucks - Up to 6 Bikes - 61" Wide
The fit for a 2014 Ram was spot on, no issue with the wide style tailgate top and the access flap for the tailgate handle lined up perfectly. Material is durable and easy to clean, the only thing holding it from a 5 stars is if it had the padded dividers on top to keep the bikes separated. But for the price, the fit and finish was exceptional, great value !!!
The product review/installation video helped me make my selection. I selected the full size pad for 2001 Silverado 1500. Installs easily, fits nicely, flap in pad is positioned for easy access to tailgate latch.
# 9
Rhino-Rack Bike Rack for 2 Bikes - 2" Hitches - Tilting
I purchased this bike rack a year ago and I use it A LOT. I had to buy and install a stabilizer because without it, the unit would sway back and forth even without a bike on it (very noisy). This makes removal more cumbersome but since I keep the hitch on year round it doesn't matter to me. The tilting function is fabulous allowing easy use of my RAV4 hatchback. I can even tilt it down with a bike on it. I got the 2 bike hitch. Plenty of room for two bikes to fit without rubbing. Lastly, the hitch has a sizable through-hole on the bottom to thread a good sized cable so I can lock my bike up. Sturdy. I highly recommend.
The unit ‘s simplicity is a real plus. It takes less than 3 minutes to put the rack on the vehicle. It is well built and very durable and has a nice feature that allows you to open the rear hatch for SUV owners without removing the rack.
# 10
RockyMounts BackStage Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
We love our RockyMounts BackStage Bike Rack. The fact that it can hold our two e-bikes and swings out for rear door access makes it perfect for vanlife. Service and communication from etrailer is outstanading!
etrailer.com asked me for a review about 1 week after it arrived. A better review would be in about 6-12 months after delivery to allow me time to use and experience the rack. Disclosure: my review is just for the assembly and install. Assembly is not easy. I needed to go to the internet and look at photos. The instructions lack detail. So only 4 stars for assembly instructions. It seems like a good design. The included locks seem cheap - like why bother including. The hitch pin design seems to tighten down the rack so there should be minimal rattle and movement. The rack sits up relatively high, so it would be safer to lift heavier e-bikes with two people or use some type of field engineered ramp. Wish it was made in the US and I wish the country of original was fully disclosed in the etrailer.com description. Perhaps it is disclosed but I learned it was from china after it was delivered.
# 11
Hollywood Racks Truck Bed Bike Carrier - Fork Mount - Bolt On
The Hollywood Racks Truck Bed Bike Carrier - Fork Mount - Bolt On, is just what I was looking for to be able to build a bike rack for carrying one of my bikes on my motorcycle. It was easy to mount and it holds my bike in place while riding on bumpy dirt roads, city streets, highways and even when I hit some twisty country roads. It's really easy to load and unload my bike when I get to where I want to ride. I use a velcro strap around the quick-release and the fork arm as an added safety as well as a couple tie-downs from my bike handlebars to my motorcycle passenger pegs to help distribute the weight on my rack. If you want to build your own DIY bike rack I totally recommend the Hollywood Racks Truck Bed Bike Carrier - Fork Mount - Bolt On.
Love this product! I built a great bike carrying system for my F-150 using two of these fork clamps. They are easy to install and extremely well made. No more tangled bikes and lots more room in the bed for other stuff! Best way to go for a nice bike rack system. Thanks, Phil T.
# 12
Swagman Truck Bed Bike Rack for 2 Bikes - Fork Mount - 9-mm Skewer
I used 2 inch square tubing cut the length of the tie down support bracket in my 2007 Honda Ridgeline and secured with a stainless bolt and wing nut, use a large enough washer to cover the diameter of the supply hole in the Honda Ridgeline bracket on the truck. A couple of notes: Be sure to use something as a cushioning gasket to insure a snug fit and to protect your truck lining. I used rubber or foam exercise mat cut to the same as the aluminum square tubing. Use a washer that a combination of hard plastic and metal to avoid the corrosive effects of dissimilar metals in contact with each other. last: My 26" full suspension bike fits, but I have swing it to one side slightly before i close the tailgate and lift the bike up and slide it down....It's a very snug fit but the suspension adds pressure to the tailgate and its works out very well. Or you could just use a tailgate extender.
Referring to special mounting instructions if you have a bed liner: (line #3). I do not have a bed liner, but I do have a molded plastic cap on my bed rails ('04 Ford F350). The first install over the plastic cap the locking pin or pin as called out in line #3 was nowhere near making contact with the metal lip of the metal bed under the plastic. What I did next on the second and final install was remove/cut away the plastic on the inside of the bed rail to allow the vertical portion of the "L" mounting bracket (Fig 4) to contact the metal bed. The locking pin is now at a position almost where it would protrude under the metal bed lip if I would remove the rest of the plastic under the horizontal portion of the "L" mounting bracket, I did not do that. After cutting a notch in the metal rail to accept the pin, the pin barely flushes out to secure the rack. A 1/4" longer pin would take care of this problem. One other thing that was not addressed in the install instructions was if you have a full size pick-up bed you are likely to attach the passenger side fork mount (Fig 2) to the right of the extension tube locking mechanism. The extension tube is a smaller diameter, so you will have resize the fork tube clamp (Fig 1) for the smaller tube. I can't explain how to do it other than it's a Chinese puzzle.
# 13
RockyMounts MonoRail Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
At age 75, I have purchased many bike racks over the years…..this one has no equal in loading and unloading…
This rack is really, good. The only thing i add to make it better is small strap that holds the front wheel to the front wheel bracket. I never had a problem with it, but i like to make sure it is secure. It is a solid bike rack and worth every penny. I would buy this over the Kuat version any day.
# 14
Yakima HoldUp Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
Works well for transporting two 29" wheeled mountain bikes. However, after one year it's starting to rust in several areas (see attached photos), and the front wheel arms are becoming increasingly difficult to raise and lower. Finally the locking cable is extremely rusty as you can see in the attached photo. I'm not sure how durable this rack will be long term.
We have had this bike rack for one year and use it every week-end. My wife has a Trek e-bike (52 lbs) and I have a regular Trek hybrid (23 lbs). The rack is very sturdy and I have no issues driving at highway speeds, there is no movement of the bikes. Very easy to load and unload.
# 15
Kuat NV 2.0 Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Metallic Black
EVERY BRAND HAS ITS PROS AND CONS. THE PROS ON THIS RACK IS THE HIGH QUALITY OF MATERIALS AND CONSTRUCTION AND THE INNOVATIVE FEATURES. THE RACK IS EASY TO USE AND EASY TO INSTALL. I ESPECIALLY LIKE THE INTEGRATED BIKE STAND. IT IS EASY TO USE, UNOBTRUSIVE, AND COMES IN VERY HANDY WHEN YOU WANT TO MAKE A TWEEK ON YOUR BIKE WHILE AT THE TRAIL HEAD OR IN THE PARKING LOT. I KNOW THERE MUST BE A NEGATIVE TO THIS RACK, BUT AFTER A YEAR OF USE I HAVEN’T FOUND IT YET. IT IS A BIT PRICEY, AND IF YOU DON’T CARE ABOUT DURABILITY, QUALITY OF CONSTRUCTION, OR ADDED FEATURES, THEN A LESS EXPENSIVE BRAND MAY WORK FOR YOU AND YOU WILL SAVE A FEW BUCKS. ALSO, IT IS A BIT HEAVIER THAN SOME OTHER RACKS, BUT I AM IN MY 70’S AND I CAN HANDLE IT FINE.
This is rack’s construction is a rock, heavy hitch tube and the scissor extension swing is solid due to the ball barring lock feature in the mounting tube. The ease of mounting bikes with tire saddles, installing and construction quality excellent. Purchased the wide tire kit adds flexibility to my use of road to fatter tire bikes. Being able to install the bike service bracket is a breeze for airing up, lubing. Use it on my Hylander to my truck camper
# 16
Yakima HighRoad Roof Bike Rack - Wheel Mount - Clamp On
1. One star ding for price. Fairly expensive for a single bike, especially after adding a lock core. 2. The rack works exceptionally well and I'm not disappointed with the purchase. Installation is fairly simple. It does take a bit of fiddling to get the tension down on the rack clamps (connecting it to car) but it is a simple affair, and I'm able to move it between an aero rack and a round rack with out adjusting the tension. The sliding tray in the rear is a bit sticky, so if you carry bikes of different wheelbases, you may need to add some lubrication to the tract. Front wheel locks into place (I've used 700x25 and 29x2.3) simply, and the clutch in the tension wheel is a nice addition. It would be nice if there was a quick release button (like in times past) but it spins fairly quickly to unload. The locking whip is a nice addition. I have been able to rout it over the chainstay on both bikes. However, it is too short to route around chainstay and wheel. I'd prefer to include my rear wheel inside the lock. Overall, I'm very happy with the product.
I bought two of these, they work great, good the bikes very solid and I'm confident using them over hundreds of miles. etrailer.com is my go-to for tracks and accessories
# 17
Inno Velo Gripper Bike Rack for Truck Beds - Clamp On
Using the Grippers for carrying 2 ebikes, weighing 55 & 75 lbs. I know this is above the rated bike weights but so far they have performed well. My short bed keeps the 75# bike pretty well locked in front to back so that may help.
I am disappointed that they don’t hold my bikes better than they do. I still have to strap them down so they don’t fall out. They are pretty expensive for what you get. I need to modify them so they will actually work. Not really what I was expecting to do, but I need to so my bikes are secured.
# 18
Kuat NV 2.0 Base Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Matte Black
I've taken this rack all over New England on the front of my Dodge Ram 3500 pick up truck with a truck camper. I had no idea it was possible to love a bike rack so much. After one drive I didn't ever worry about it again. So nice that it locks up when I am camping or taking a quick stop for food on the road. So glad I bought it from etrailer. They totally help me pick the perfect rack for my challenging set up.
Still very new, but what an awesome bike rack! Assembly was a snap and the rack is rock-solid when you secure it to the hitch receiver. etrailer was amazing too - excellent communication, price and fast, free delivery. Overall I am extremely happy with the rack and service!
Yakima Truck Bed Bike Racks Review - 2022 Ford F-350 Super Duty
`- Hi, everyone. Aiden here with etrailer.com and today we're gonna be taking a look at the Yakima GateKeeper tailgate pad for full size trucks here on our 2022 Ford F350 Super Duty. Now you can get this in blue, like we have here or black if you want something more neutral. And it's gonna be able to hold up to six bikes in your bed, upright like this draped over the tailgate with this pad protecting your paint. You get a pretty good solid hold on the bike here. And if you're looking to get a large amount of bikes to your destination, this is a great way to do it especially with the larger hitch size.
Swagman Truck Bed Bike Racks Review - 2022 Ford F-350 Super Duty
Hi, everyone. Aiden here with etrailer.com. And today we're gonna be taking a look at the Swagman Tailwhip Tailgate Pad for your full size trucks here on 2022 Ford F-350 Super Duty. Now a tailgate pad is a great solution for either getting more bikes than the standard four bike capacity of a hitch bike rack or maybe your hitch is occupied, or in this case we don't have a two inch hitch. So there aren't really any options without using an adapter sleeve. So the next best place is our tailgate, and in our truck bed.
Swagman Truck Bed Bike Racks Review - 2022 Ford F-350 Super Duty S74FR
Hi everyone, Aiden here with etrailer.com. And today we're gonna be taking a look at the Swagman Paramount tailgate pad for full size trucks here on our 2022 Ford F-350 Super Duty. Now, if you're looking to haul a very large amount of bikes, it's gonna be a great way to do it. But another thing to consider with your F-350 is the larger than normal hitch size. So a normal bike rack isn't going to be the best solution sticking in the hitch because you will need an adapter sleeve to size down. So having this, it's a great way to accommodate that.
Swagman Truck Bed Bike Racks Review - 2016 Ford F-350 Super Duty
Howdy everyone, John here and today we're gonna be taking a look at the Swagman Paramount on our 2016 Ford F350 Super Duty. Now this is gonna be a great choice if you wanna get your bikes and maybe some friends bikes out to the trail, without having to worry about them jumping around and being damaged in the back of your tailgate. Now this is going to be for a full size truck. So this is gonna be 61 inches from both sides and it holds seven bikes. Now that's a lot of bikes and you're probably asking yourself how is it able to hold that and keep them from damaging both themselves and the bed of your truck Well, as you can see, it's made out of foam. It's made out of a really nice material and underneath we've got this nice plush padding that's going to protect your tailgate.
Thule Hitch Bike Racks Review - 2016 Ford F-350 Super Duty
Today, on our 2016 Ford F350, we're test fitting the Thule Roadway. Now, this is a hanging style 2 bike rack. It's been designed for use with the 1 1/4" over 2" hitches, part number on it is TH912XTR. Now, the Roadway's a really straightforward, simple, and very easy to use bike rack. We've got 3 straps that're going to hold our bike in place, 2 up here for the frame on the top and we've also got an anti-sway cradle, there, does a nice job of keeping the bike from moving back and forth. To release it, we'll just pull down and out on our straps, and we can bring our bike right on off.
Thule Hitch Bike Racks Review - 2016 Ford F-350 Super Duty TH9029XT
Today on our 2016 Ford F350 Super Duty we've got out the Thule Vertex here, and we're doing a test fit on it to see exactly how it works on the back of the vehicle. The Vertex is a four bike hanging style rack. It folds and tilts. There's a lot of versatility. The part number on it is TH9029XT. I like the incorporated cable lock that we've got right up here at the top.
Thule Truck Bed Bike Racks Review - 2015 Ford F-350 Super Duty
Today on our 2015 Ford F-350, we'll be doing a test fit of the Tooley Instigator truck bed single bike rack. Part number TH501. We already have the bike on the rack. I'm just going to show you a few features of it. The main feature I want to show you is the frame hook its self; how it's engaged and how you disengage it. It's a button down here, black button, press on that. Just bringing it out just a little but and you can bring it down towards you.
Inno Truck Bed Bike Racks Review - 2015 Ford F-350 Super Duty
Today on our 2015 Ford F-350, we'll be doing a test fit of the Inno Velo Gripper Bike Rack. Part number is INRT201. Now, we already have a bike on our rack. We'd just like to show you a few features of it. Now, how we have our bike connected, we have two straps. One is going around our forks here, and the other one is going around our side row here.
Thule Truck Bed Bike Racks Review - 2015 Ford F-350 Super Duty th824
Today on our 2015 Ford F-350, we'll be doing a test fit of the Thule Gate Mate Tailgate Pad and Bike Rack. Part number is TH824. Now, we have it right here. We're going to show you how we install it. This is 62 inches long. It's going to be good for your extra long tailgates. First thing first, we want to do, we're going to go ahead and just show you a couple features here, now.
Kuat Hitch Bike Racks Review - 2011 Ford F-350 Super Duty
Hey everyone, Charles here at etrailer and today we're taking a look at the Kuat NV 2.0 bike rack on a 2011 Ford F 350 Super Duty. This bike rack is gonna be great for carrying a lot of different styles of bikes as well as the weight capacities. We can carry up to 60 pounds per bike and this front wheel mount is gonna make it great for your carbon frame style bikes because you're not gonna warp or damage the frame. And it's also great for carrying any of those bikes with the odd shaped frames like the women's step through bikes. This bike rack has a lot of cool features that add up and make this a really premium option. For one, built in bike cables and locks right into the tray here.
Kuat Hitch Bike Racks Review - 2011 Ford F-350 Super Duty SH12B
Hey everyone, Charles here at etrailer and today we're taking a look at the Kuat Sherpa bike rack on a 2011 Ford F-350 Super Duty. This bike rack is gonna be great for hauling any bike that is up to 40 pounds per tray and the front wheel mount is gonna make it great for your carbon frame styled bikes because you're not gonna warp or damage the frame. And it's also gonna be great for your women's step through bikes or really any frame that's odd shaped. One of the cool features about this rack is the tilt away feature. And that way we can leave our bikes on and still have room to jump on the tailgates to grab our helmets or waters, whatever we need for our bike ride. We also have an integrated lock core for our bike cables and they are gonna be keyed alike with the lock that comes included on your hitch pin as well.
What our customers are saying:
"Sent out an e-mail to you earlier this week asking which hitch woudld be the best choice for installing on a 2000 Venture van for hauling a bike rack with two bikes. You suggested the one that would be easiest to install..received in a matter of days..installation went great ..very well thought out instructions. Everything went smooothly and the hitch is up nice and snug..doesn't stick out..looks great."