Most Popular Fixed Ball Mount for Ford Edge

Retail type stores only carry mainstream items so when I needed a special length ball mount for my 2011 Traverse I found the size and quality with Curt Products .

Looks great. Fast delivery!

Very happy with this ball mount - provides just the amount of drop we required for a level tow of our GeoPro travel trailer by our RAM2500. Plus, the extra length not only allows a tighter turning radius, but also allows us to lower the truck tailgate without having to detach the trailer. Huge improvement on all accounts for us compared to our prior setup. The product is well built and I'm confident will provide us years of good use.

Great customer service. Live in SC - ordered a hitch and USPS delivered it to PUERTO RICO. Go figure. Stacey A refunded my money - but 2 weeks later hitch appeared on my doorstep. All’s well that ends well.

Overly tight on the receiver end bit functions as intended.

I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.

This ball mount has served it purpose well. I purchased a new travel trailer that is heavy enough to require a weight distribution hitch when using the factory installed Class III hitch on our Dodge RAM 2500. I decided to upgrade to a Class V hitch combined with this ball mount to take delivery of the TT in order to defer decisions about a WD hitch until the actual load conditions were known. The hour trip home with this setup worked very well. Once the trailer was outfitted I was able to determine the actual tongue weight of the loaded trailer and I decided to purchase an appropriately sized Reese Straight Line WD hitch. However, this ball mount comes in handy for moving the trailer short distances without hassling with the WD system. The purchase experience through etrailer.com was first rate.

I was surprised at the heft and quality of the ball mount. Shipping was fast, communication good, easy and informative website to use. Thanks etrailer, you have earned a new customer!

This is a great all-purpose hitch. I've used it to mount a heavy-duty bike rack and a steel T-rack to carry a canoe as well as lumber. Most recently I hauled 5 x 8 cargo trailers full of plants, then furniture for a 600-mile move. It was simple to use, problem free, very strong and sturdy. Now that I live on some acreage, I see a trailer in my future, so this will get a lot more use. I drive a 2013 Tacoma, so this is a good size hitch at a good price with sufficient capacity for my needs. I do use a key lock for the hitch as well.

I actually got my hitch the date they said it would be here to my surprise. When the box arrived it was pretty much beat up, not the hitch just the box. I wished there was instructions how to install it. Overall very satisfied and will buy from 5hem again

This draw bar in perfect for my John Deere X738 tractor. What I like about it is the ¾” rise it keep the draw bar height at about the same as the factory frame so the attachments height remain level. Thanks for the great product.

Not much you can say about a bar with a piece of flat metal welded to it; well made looks good. What is really important is that e-trailer is fast, friendly and knowledgeable. I've ordered from them anytime I needed a trailer/RV part.

This ball mount fit the SUV just right. I needed a 5 inch rise and the mount angled away from the bumper. However, the load capacity was way more than I needed, but the fit made up for that. It's a little loose in the receiver so I will be adding a stabalizer to lock it in place.

Did not work on my truck due to custom rear bumper. Looks great on my friend's 2018 F350 4 X 4 diesel!

The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.

Works great solid product.

Purchased to extend the trailer away from the back of the vehicle, and increase the drop. Initially could not fit in to my receiver, eventually figured out that the end of the 2" square was mushroomed, had to remove excess metal with a rotary tool. now it fits as far as the first 5/8" pin hole. No issues with use - seems sturdy, metal finish seems durable. Didn't drop the trailer tongue as much as I had hoped, but that's on me - I was probably running a 3" drop before, but I thought it was 2".

Dual length to get past a spare tyre mounted to the rear door. The 1’ hole allows for a heavier grade of ball to be mounted. The product is well made and packaged. I found etrailer some years ago after doing a global search for a product that I needed. I have found the company to be top notch in terms of service, price, availability, communication and customer service - it’s now my go-to company for trailer (and other) related products.

Heavy duty , very good quality.

I hooked up the draw bar today for the first time to the trailer that I built and the hitch I installed. The draw bar uses a cotter pin that slides on the bolt rather than going through a hole to mount the bar to the hitch. I have never used a sliding on pin in anything - I've only used those that go through a small hole matching the pin. This includes my farm tractor and other tools. I hope it is secure because it does slide on easily. The bar itself appears nice and strong.

We used our car hitch and cargo carrier last summer in a Honda Accord to support a cargo carrier. It held up great on a 4,000 mile camping/hiking trip from Mid Missouri to Glacier National Park, MT. We were able to use the carrier/hitch to carry our large tents and baggage (approx 120#)directly behind our car trunk. Initially I was a little hesitant at the smaller 1-1/4" tube hitch, but it was very stable throughout the long trip. Sure was a lot less drag than putting all our gear on a roof cargo carrier.

Exactly what I needed. All my previous SUVs used 2x2 hitch mounts which now are useless.So I decided to gift them to my son. The hitch mount is well made. etrailer is fast and very easy to find exactly what you need at a fair price. Customer service is friendly and helpful.

Perfect fit for my hitch and trailer. Pulled really well.

This is the perfect rise to tow a small trailer for moving.

Again, Will the eTrailer rep really helped me get exactly what was needed for my application which was a little out of the ordinary. I could tell he had the knowledge and experience to direct me to the correct solution.

Good fit, well made, worked well on first use, ball attached easily, was the reciever I was looking for.

Products came sooner than expected with it being so close to the holiday. Everything has gone together as expected. I included a photo of where the hitch height is on our 2013 Dodge Grand Caravan which I would have appreciated while deciding on which products to purchase. Thank you!

We really like the hitch we ordered for our Camry. It was extremely easy to install. Fit perfectly!

Wonderful product. I had the hitch installed in 10 minutes. The wiring was a little more tricky because it required running a power wire all the way to the battery. I towed my trailer from Florida to Tennessee and back. Etrailer is still wonderful to deal with as they always have been in the past. My hitch came in a couple of days. I wouldn't think of ordering from any one else.

I'll start off with the great customer service, called a rep for assistance and did a great job. He walked me through everything for about 5 minutes. Then I proceeded to order parts at a very reasonable price. Shipping was right on time and tracking was top notch. Now for the parts I received. Trailer hitch receiver was built like a tank, and very easy to install. I didn't even have to take off the whole bumper which I see on your website. There is only one problem with this hitch receiver. Zip ties to hold the facia bracket? It's like putting a $10 paint job on a Rolls Royce. I'm sure you have a good R&D department, but this is unacceptable. I could tell you how to make this better but I'm not part of your team. Could be solved by putting a ___ on the ______. R&D should be smart enough and paid well to figure this out. No offense but they can do better. ??ZIP TIES?? Also, it is pitched with a cap but did not receive that. I also purchased A brake controller P3 and a ball hitch. The ball hitch is pictured wrong on your website. It's pictured with an adjustable ball hitch. This is what really wanted but got something entirely different. If it works, I'll be fine with it. I should have caught that, but my eyes adjusted on the adjustable ball hitch. P3 brake controller was very easy to install, about 5 minutes. On a closing note, I will order from etrailer again. Thanks for your business. Just please listen to your customers and fix these problems. Everything and everybody are not perfect. Thanks again.

The hitch assembly included everything needed for quick and complete installation. Perfect fit for my 2023 Honda Passport. Have been using etrailer for some years now and have never had a bad experience. The self-help videos are a plus for customer service. Good work guys!

The hitch and ball mount are excellent quality. My concerns are twofold. The hitch is so heavy that I had to take it to my mechanic to have it installed. Minor cost and inconvenience, but the hitch for my previous F-150 was just as sturdy, but easy to install myself (albeit with higher ground clearance). My concern about the ball mount is that the factory told me erroneously that it could not be reversed for a drop, so I returned it. This order is for the replacement after I was finally correctly told it could be reversed and how to do that. Ball mount would have been a 3 for that reason, and overall hitch and ball mount quality a 5. So I averaged them.

I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.

To be honest, I use it upside down. I needed a hitch with rise, but none were available at time of purchase, and yours, inverted, works perfectly! The welds are regularly checked and remain all secure. It's a good hitch.

Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.

I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.

I purchased this for use with a friction anti sway device I installed on an enclosed V nose trailer. It worked well.

We sold our small motor home and purchased a small travel trailer. This hitch provided a perfect solution to how to use our bike rack while towing the trailer. It even allows room for the pickup tailgate to be lowered without removing the bikes from the rack. The hitch is very hefty with a high weight limit - plenty for the GVW of the trailer (7,000#) plus 125# of rack and bikes.

This has been an amazing multipurpose ball mount. We purchased this to use with our Hollywood Bike Rack and also to connect onto our boat. We weren't sure if this would work, but it was awesome. It is very well built and We had to make some minor adjustments to the position of our boat on the trailer so the turning radius of the bike rack that was attached would clear the truck. This is very well made and solid.