# 1
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
I am very pleased with the hitch, ball mount, and electrical package. All were easy to install if you follow the easy to understand directions. An added plus for putting one of these on a MINI is that the hitch can be hidden behind the "black plate/cover" that is on the rear bumper. It looks just like it came out of the factory except when to need to install the ball mount. The service has been outstanding. This is the place to go.
# 2
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!
Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.
# 3
Draw-Tite Ball Mount for 2" Hitches - 3" Rise, 4" Drop - 9-1/4" Long - 16K
Perfectly as described, Box was a heavy hitch and the box must have been damaged in shipping so it was a little delayed. You can't mess up a forged hitch it still is in excellent condition.
This simple ball mount will get the job done. It's a solid casting so it weighs a lot.
# 4
Draw-Tite Ball Mount for 2" Hitches - 1" Rise, 2" Drop - 8-1/2" Long - 16K
This is a beast of a drawbar, solid forged steel & well finished. It's also very heavy and E-Trailer needed to ship 3 times because the first two broke out of the box they were packed in. (Someone in the USPS has a couple nice draw bars.) Fortunately the 3rd effort was much better packed in a reinforced box and was successfully delivered. E-Trailer customer service was exemplary in resolving the shipment issue & I will definitely shop with them again.
I had a great experience ordering from you. Your organization kept me completely up to date with the order & shipping process and delivered the exact products I ordered. Attached is a photo of the 16,000 lbs capacity hitch and 30,000 lbs 2 5/16 ball you sold me in use. The boat and trailer total about 12,000 pounds. Thanks again.
# 5
Convert-A-Ball Ball Mount for 2" Hitches - 8-3/4" Rise - 10" Drop - 8,000 lbs
Works great. Needed the drop to tow a utility trailer at level.
Have pulled trailer several times with this hitch. Very impressive, smoother and easier on truck than conventional hitch, less jerking and bounce.
# 6
Convert-A-Ball Ball Mount for 2" Hitches - 10-3/4" Rise, 12" Drop - 7,000 lbs
Needed a large drop hitch to pull my car trailer. This item came quickly and worked perfectly.
This extreme rise ball mount is what I need to make my passenger car into a back-up trailer puller. It is well built and has a welded strut to reinforce the long rise/drop ball mount. The "shock damper" feature is sure to help absorb the leverage movement that a rise/drop ball mount passes on to the hitch receiver itself.
# 7
Draw-Tite Ball Mount for 2" Hitches - 5" Rise, 6" Drop - 10-1/4" Long - 16K
Its been a year and I aint broke it yet. I use this hitch to tow my 7Klb trailer. The trailer is tongue heavy and I needed something rugged to tow it with. Haven't had any troubles with this hitch.
This ball mount fit the SUV just right. I needed a 5 inch rise and the mount angled away from the bumper. However, the load capacity was way more than I needed, but the fit made up for that. It's a little loose in the receiver so I will be adding a stabalizer to lock it in place.
# 8
Curt Heavy Duty Forged Ball Mount for 2" Hitches - 5" Rise - 6" Drop - 17,000 lbs
Very heavy duty and perfect.
This is one solid hitch. Bought the hitch to pull about 5000 lbs. there's no doubt in my mind that it can handle it.
# 9
Convert-A-Ball Ball Mount for 2" Hitches - 6-3/4" Rise, 8" Drop - 10,000 lbs
I use this hitch when I pull my horse trailer to make the stop/start transitions as smooth as possible for the horses in the back. It works great. I also love that its a category IV hitch. Really heavy duty. My truck sits pretty high, and the amount of drop - 8" is perfect. I never worry about hitch failure travelling with my horses - they're a heavy load, and any failure would be a disaster. E Trailer provided excellent service, and their shipping to Canada was prompt and hassle free. Way to go guys, keep up the great work!
I have a 2012 GMC Sierra HD with a 12" suspension lift. I recently purchased a ball mount hitch with 8" inch drop for our 36' RV trailer and it worked great. It took 3 days for the hitch to get to me. Great service from e-trailer.
# 10
Curt Heavy Duty Forged Ball Mount for 2" Hitches - 3" Rise - 4" Drop - 17,000 lbs
I just opened up my new Class 5 Curt XD hitch and have not yet installed it so my comments are based on first impressions only. It is very heavy duty - and heavy at 40 lbs. - made of extremely thick metal and outfitted with quality Grade 8 bolts with square necks so they won’t turn when torquing on the nuts to attach the main tube to the side mounting plates. My bolts are plated yellow (which I like) rather than silver as you may have seen in some online photographs. It is substantially beefier than my existing Grade 4 hitch and superior in every way. It’s an impressive piece of hardware. I cannot imagine anyone being disappointed with it on specifications, quality, strength, and general appearance. It’s a beast. What I AM disappointed in is Curt’s packaging and the condition in which the hitch arrived. (This is NOT a reflection on etrailer.com as the hitch arrived in Curt’s original packaging.) The unassembled main tube and the two side mounting plates come bundled together with nothing separating them but shrink wrap. No cardboard, plastic, even paper coming between the metal surfaces - just shrinkwrap probably not even a couple of mils thick. With basically metal-to-metal contact in an oversized-box with the bundle jostling around, it would be a miracle if there were no scratches, gouges, or some type of damage to at least one piece, which is exactly what happened to my hitch. The main hitch tube, on the exterior facing plane, on the driver side where I’ll see it every day, has some gouges on it that go through the powder-coating to bare metal. I can - and will - paint them to prevent rust (and, therefore, have to paint the whole hitch to match). But the gouges will still be noticeable as they go through the thicker, pebbly, powder-coat finish and will undoubtedly still appear as depressions in the surface even once painted. I fully realize this kind of surface damage will almost certainly happen with regular usage of the hitch anyway and that it’s certifiable to demand absolute perfection in anything. But if you are someone who cares about the aesthetics of your equipment and keeping it looking new for as long as possible, it is very disappointing to receive such an expensive and prominent piece of hardware damaged right out of the box and requiring immediate repainting. The plastic parts bag had also ripped open in transit, with nuts, bolts, shims, etc. rattling around in the box. I am dumbfounded that Curt packages such a high-quality piece of equipment so shoddily where such damage is virtually unavoidable. I bought from Curt solely due to their being an American manufacturer and to support American workers so this is doubly discouraging. It’s a trivial complaint in the big scheme of things and not worth demanding a replacement over. Just be aware that unless Curt changes their packaging practices it is very possible you will have the wind taken out of your towing project sails just as I have. Again, this in no way reflects on etrailer. My experience to date with etrailer (website, educational resources, staff reviews, ordering, tracking, email contact, etc.) has been beyond exemplary in every way. They rank as a Top Five online retailer in my opinion, maybe even the best.
First of all, the products you find at etrailer are not your garden variety, home depot kind of fair. Much higher quality and grade/weight ratings. So to be able to get hard to find items and then by orderring at least 100$ worth of stuff also get it delivered free in 4 days, is awesome. The prices are incredible too.
# 11
Draw-Tite Ball Mount for 2" Hitch - 7" Rise, 8" Drop - 9-1/2" Long - 12,000 lbs
Heavy Duty Drop Down Hitch no problem pulling a 10,000# trailer
It fits perfect on my f350 diesel, super heavy duty. I'll be using it for towing my car tilt bed trailer.
# 12
Reese Ball Mount - 3-1/2" Rise, 5" Drop - 10" Long - 18,000 lbs
I have a 2015 Ford F-250 with the factory 2.5" receiver hitch. This drop ball mount fits into the factory receiver well, contrary to the product warning. It is also extremely beefy, you will not be disappointed! Photo fitment proof!
Very Strong ball mount. My wive (its her truck), towed 7000# of horse, tack and trailer last saturday. I know this ball mount is overkill but it is easier than using a 2" with the receiver adapter. Also this way if we have to tow something real heavy we already have the ball mount for it.
# 13
Curt Heavy Duty Forged Ball Mount for 2" Hitches - 1" Rise - 2" Drop - 17,000 lbs
I bought my first ball mount way back when I was broke (bought the cheapest one in the big box store). With my new trailer I needed 14k capacity instead of 10k so I double checked the mount before buying a heavier duty ball...it was rated for only 5k!! Folks, check those mounts to make sure they're rated for the job!! This one is a honker btw, love it. Side by side with old it's like brick vs bubble gum, embarrassing I haven't upgraded sooner. And thanks for the guidance.
# 14
Curt Forged Ball Mount for 2-1/2" Hitches - 1/2" Rise - 2" Drop - 20,000 lbs
Very good heavy duty rating which is what I wanted. etrailer was great to work with
I have been towing trailers many years With no issues until recently. Trailer weights have increased and loads also. My three way ball with 2 5/16 was torn off of tubing because of insufficient welding, I was very lucky. Yes I went to a solid receiver with bolt style ball. Very great setup. Thanks curt for designing heavy hitches and etrailer for easy ordering.
# 15
Curt Forged Ball Mount for 2-1/2" Hitches - 2-1/2" Rise - 4" Drop - 20,000 lbs
Hitch ball and mounts all ready to the test!!! Great Products!! Five Star e-trailer team, very informative, fast and accurate shipping, perfect packaging and "GREAT" customer service"
This review does not just serve my recent order, but all of the orders before it. I have purchased a number of items from etrailer and everything was sent in a timely manor as stated and promised. All of the items I received were exactly as described. I watched a number of videos, read a number of diagrams and all of the help information was exactly what I needed. In other words I did not need to go anywhere else to get a full tow package for a Dodge 5500 that did not have one. I cannot say enough about how this website helped me. Also the pricing was about the best I could find and I did a lot of searching to make sure. This is a top notch site and I will absolutely come back here for my future towing needs.
# 16
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
Makes for a great hard-core dirt road set up with a 3000 pound trailer, in conjunction with the Curt rocker ball, Towing with an F150 over many miles of washboards, down through washes where the road was washed out, etc. Really makes for a gentler set up on the equipment in the trailer and the truck. Thanks a lot E-trailer!
My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks
# 17
Convert-A-Ball Ball Mount for 2-1/2" Hitches - 4-3/4" Rise, 6" Drop - 18,000 lbs
These hitches are the best! And I scanned the world over to find only hitches that are made in USA like I do every product I buy. This is a very ingenious design that allows some shock absorption that greatly quiets any trailering. I bought two full hitches one for each ball size so that I would never have to change ball again! Great product!
Just received this mount and did the test fit with our trailer. We have not hit the road with it yet but I am confident it will perform perfectly. I am anxious to see how the cushioned feature works. We pull a box cargo trailer for business and just got a new Chevy HD pickup to tow with. It has a 2.5" receiver and hitch height is much greater than the Suburban we were using plus it had a 2" receiver. This mount is rated for far more weight than we will ever need but it was the only 2.5" size with 6" drop that I could find. We are very pleased with the product and the excellent customer service we got at etrailer. Thanks to everyone there for the very fast service and for keeping me informed as to the status of my order. well done!
What our customers are saying:
"I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future."