# 1
Swagman Truck Bed Bike Rack for 2 Bikes - Fork Mount - 9-mm Skewer
I used 2 inch square tubing cut the length of the tie down support bracket in my 2007 Honda Ridgeline and secured with a stainless bolt and wing nut, use a large enough washer to cover the diameter of the supply hole in the Honda Ridgeline bracket on the truck. A couple of notes: Be sure to use something as a cushioning gasket to insure a snug fit and to protect your truck lining. I used rubber or foam exercise mat cut to the same as the aluminum square tubing. Use a washer that a combination of hard plastic and metal to avoid the corrosive effects of dissimilar metals in contact with each other. last: My 26" full suspension bike fits, but I have swing it to one side slightly before i close the tailgate and lift the bike up and slide it down....It's a very snug fit but the suspension adds pressure to the tailgate and its works out very well. Or you could just use a tailgate extender.
Referring to special mounting instructions if you have a bed liner: (line #3). I do not have a bed liner, but I do have a molded plastic cap on my bed rails ('04 Ford F350). The first install over the plastic cap the locking pin or pin as called out in line #3 was nowhere near making contact with the metal lip of the metal bed under the plastic. What I did next on the second and final install was remove/cut away the plastic on the inside of the bed rail to allow the vertical portion of the "L" mounting bracket (Fig 4) to contact the metal bed. The locking pin is now at a position almost where it would protrude under the metal bed lip if I would remove the rest of the plastic under the horizontal portion of the "L" mounting bracket, I did not do that. After cutting a notch in the metal rail to accept the pin, the pin barely flushes out to secure the rack. A 1/4" longer pin would take care of this problem. One other thing that was not addressed in the install instructions was if you have a full size pick-up bed you are likely to attach the passenger side fork mount (Fig 2) to the right of the extension tube locking mechanism. The extension tube is a smaller diameter, so you will have resize the fork tube clamp (Fig 1) for the smaller tube. I can't explain how to do it other than it's a Chinese puzzle.
# 2
Swagman XC2 Bike Rack for 2 bikes - 1-1/4" and 2" Hitches - Frame Mount
I like the overall design of this rack, but unfortunately after hauling a couple bikes around for a while the point where the crossbar connects has apparently rounded off so the rack swings back and forth. I've used rope to tie the ends of the rack to the car to stop this from getting worse, but it's inconvenient. Note: the hitch connection itself is good and solid, but the point where the crossbar connects to the bar coming from the hitch has gotten loose and there's no way that I can see to tighten it.
I own a 2005 Jeep Wrangler X with 31x10.5x15 oversized tires and wheels. I installed B6196001 HighRock 4x4 Oversize Tire Carrier by Bestop to carry larger spare tire. I needed a bike carrier that would carry our two crusier bikes and clear my spare tire. After measuring, I ordered: -> S64650 - Swagman 2-bike carrier -> 80300 - 7" Hitch Adapter 2" to 1-1/4" Trailer Hitch Receiver -> RM-061 - Roadmaster Quiet Hitch for 2" Trailer Hitches Our order arrived very quickly, etrailer.com upgraded the shipping. All these products arrived well packaged and without damage. In 15 minutes I had every thing assembled, installed on my Jeep and bikes loaded. The bike carrier is very well constructed, finish is excellent and easy to adjust. When adjusting wheel loops and loading bikes, make sure you pay attention to bike pedal position. I chose this extension because I did not want to use the adapter that comes with the bike carrier, I wanted as few parts as possible to keep rattles to a minimum and gives me more options for towing. The anti-rattle bolt/pin firmly secures the bike carrier to the extension and the Roadmaster Quiet Hitch keeps the extension adapter from rattling in the receiver. Road tested approximately 25 miles over rough city roads ( including railroad tracks ), county roads and highway. Bikes traveled very well without any rattles. I can remove my complete setup quickly, fold and put in rear of Jeep if desired. I am very well pleased with my purchase. Note to etrailer: Please consider offering Roadmaster Quiet Hitch in black to match receiver and accessories. Paul In the Land of Oz . . . Just South of the Yellow Brick Road!
# 3
Softride Shuttle Pad Tailgate Pad for Mid-Size Trucks - Up to 6 Bikes - 54" Wide
Order process was easy & information was great. The order processed quickly & came on time. It looks & works greats. It was easy to put on & took only a few minutes to install. I have 2 expensive bikes & one is an extra large frame. It fits great. The only thing I had to add when transporting was a strap around the tires on my tailgate as a precaution & to prevent any movement. It would be fine without it & the product works exactly as I expected. I put in on a 2000 Toyota Tundra. Very Happy! Exactly what I have been looking for & the price was just right. Thank You!!!
Received this tailgate cover very promptly, two days ahead of scheduled delivery date, and just in time to use yesterday. Cover was dry easy to install ( no directions required) and fit my tailgate well. I particularly liked the included Velcro tie downs and access pocket, which allows you to utilize your tailgate release. As you can see from the attached photo, it easily accommodated 4 additional bikes w/ front wheels still attached, and allowed me to transport 7 total bikes of varying design. Our 4 hr drive showed no indication of movement and the cover stayed in place securely. Great product!
# 4
Inno Velo Gripper Bike Rack for Truck Beds - Clamp On
Using the Grippers for carrying 2 ebikes, weighing 55 & 75 lbs. I know this is above the rated bike weights but so far they have performed well. My short bed keeps the 75# bike pretty well locked in front to back so that may help.
I am disappointed that they don’t hold my bikes better than they do. I still have to strap them down so they don’t fall out. They are pretty expensive for what you get. I need to modify them so they will actually work. Not really what I was expecting to do, but I need to so my bikes are secured.
# 5
Swagman XTC4 Bike Rack for 4 Bikes - 2" Hitches - Frame Mount
If you've done any research or read any of the other comments on either this rack, or this seller...rest assured they really are as good as everyone says! I ordered my rack on around 4pm est on a Friday afternoon and within an hour I received an email that said they have shipped my product AND upgraded to priority shipping. Can't say enough positive things about the customer service! When the rack arrived, it took me a little over half an hour to get it set up. Probably would e been faster if I were even slightly mechanically inclined (or if didn't I didn't have to borrow a socket wrench from my neighbor). We finally had an opportunity to load up the bikes and head out for a ride today. As others have said, the first time you load up your bikes, it's kind of like a puzzle to get them situated. Took about 15 minutes. This rack is awesome! Very sturdy and the bikes were very secure. Only racks I have had in the past were rooftop fork mount racks. This is so much easier! On e we got to the trail (over an hour drive) getting the bikes off was a piece of cake. Afterwards, it was time to load them back up and it was less than 5 minutes to get them all on and ready to hit the road. There were other 4-bike racks on the website, but this one had enough great reviews that I felt comfortable making the purchase. After the fact, I'm very glad I did! I can't imagine the $800 rack can be that much better than this, and I highly recommend this for anyone looking for a 4-bike platform rack. I will definitely recommend this rack and etrailer.com to everyone I know.
Loads and unloads bikes super fast, and holds them firm. Wish I would have purchased this a long time ago instead of struggling with my old frame mount rack. I actually ride more because I don't dread having to load. Adjusts to different bikes easily. Time will tell if the fittings, springs, straps hold up to weather (I leave it on car). It is fairly large and heavier than the more expensive 4 bike racks (it's mostly steel vs. composite plastic), so if you are going to take it off hitch and store it - be prepared. Only recommendation I have is to add softer foam on the frame bar for traveling on rough roads.
# 6
Thule Hitching Post Pro Bike Rack for 4 Bikes - 1-1/4" and 2" Hitches
The good: I like the way the bikes are held in and the ability to add the upright adapters to the bike frame holders. The straps are quality too. For a jeep with a spare tire, this is the perfect length to clear it. This rack is 5 stars from the bike holders to the base of it. The bad: the 2"receiver adapter and bolt are insufficient. I wish they made this in a solid 2" hitch. The entire setup is held into the receiver by a very short bolt. It only goes about half way into the receiver tube. So your hitch is only "secured" on one side. A hitch pin or bolt should go through the receiver tube completely imo so it can be secured on the other end with a retaining clip or nut. Because this only goes in the one side, the entire weight of the rack plus bikes are held tight to one side of the receiver by the undersized bolt and washer. A few bumps down the road and that bolt loosens. Now instead of distibuting the weight of the rack and bikes on the receiver and post, it's completely up to the bolt to keep you from losing the rack. The bolt threads get damaged too. I took this down a dirt road and nearly lost everything. I had to buy my own bolt with hd fender washers and lock washers to correct this. Thule should've provided this from the start. The current short bolt design where only one side of the receiver secures the rack is unacceptable. This rack is 1 star at best for the connection to the receiver.
I bought this bike rack back in April but wanted to make sure I used it to give the best review. First I want to say I did a lot of research on bike racks and found this one to be the best one to fit my needs. The best price I found was on etrailer.com, at the time it was When I called the customer service to place my order, I spoke to Dan. He was very pleasant on the phone and took the time and listened to what I needed and understood my concerns. I ordered the bike rack and also ordered the Thule Snug Tite Hitch Lock and Anti-Rattle Device and the Thule Cable Lock w/ One Key System Lock. Dan suggested I also get the Thule Bike Adapter Bar, which I never even thought of getting. Delivery was in about two business days, which was really fast and at the time of order they were running a special free delivery over $99. When I went to put it together I noticed I was missing the flat cap screw M6 x 16mm, part number #853-5787-02. I emailed Dan and within 24 hours received an email that the part was sent out and also in the email their was a link to track the order. After I received the part I did notice that the flat cap screw was actually in the 2 inch adaptor sleeve. The instructions were very easy to read, and it took me about 20 minutes to put together. I did have an issue when I positioned the stinger into the cradle, with the 8mm locking nut, it was not staying tight and when I took it off I noticed the threads inside were gone, so I ended up going out to Lowes and buying a new one and its holds perfectly fine. I also had a question about that part because it is not a locking part and was worried someone would try to steal the rack. I contacted etrailer.com to find if they make a locking device for this and they said no but I can contact Thule to double check, I'm still waiting for an answer back from Thule. The weather finally broke and we installed the rack onto my hitch, tightened it and it doesn't rattle. When I finally used the rack and put my bike on, it did sway a little but at 50 mph I was very happy with it. The trailer comes out just enough away from my car that I do not have to fold completely out and I can open my trunk with no issues. I am very happy with my purchase and had a great customer experience with Dan. Would highly recommend ordering from them to anyone.
# 7
Hollywood Racks Truck Bed Bike Carrier - Fork Mount - Bolt On
The Hollywood Racks Truck Bed Bike Carrier - Fork Mount - Bolt On, is just what I was looking for to be able to build a bike rack for carrying one of my bikes on my motorcycle. It was easy to mount and it holds my bike in place while riding on bumpy dirt roads, city streets, highways and even when I hit some twisty country roads. It's really easy to load and unload my bike when I get to where I want to ride. I use a velcro strap around the quick-release and the fork arm as an added safety as well as a couple tie-downs from my bike handlebars to my motorcycle passenger pegs to help distribute the weight on my rack. If you want to build your own DIY bike rack I totally recommend the Hollywood Racks Truck Bed Bike Carrier - Fork Mount - Bolt On.
Love this product! I built a great bike carrying system for my F-150 using two of these fork clamps. They are easy to install and extremely well made. No more tangled bikes and lots more room in the bed for other stuff! Best way to go for a nice bike rack system. Thanks, Phil T.
# 8
Swagman XTC2 Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
First-time rack buyer / owner / installer. The rack arrived in a timely fashion, maybe a day or 2 ahead of schedule. It was well packaged. I’m LOVING this bike rack. It was easy to put together and to mount on my new Honda Passport. Thus far, no squeaks in my 2” receiver. Hardest part of initial set-up is figuring out the best way to position two bikes. Trial & error and some patience. The directions weren’t clear as to where the 2 left-over screws went. I found the answer in another review and have posted a pic in case others have the same problem (photo with pen pointing at screw). These screws go in the underneath side of both of the folding arms. They appear to keep the wheel wells from sliding off in case in you drive with an empty, un-folded rack, and forgot to tighten down the wheel wells. The folding arm push / pull pins can be difficult at times. I coated the tips with some lube. That and a little jiggling seems to solve that issue. I guess it’s better for the pins to be snug vs popping right out. I added a small Master lock to the hitch pin (in lieu of the provided cotter pin) as a theft deterrent. I read that a 3/16 shackle lock will fit into the bike clamp down arms to also act as a deterrent. I had an old 3/16 lock that did snugly fit and appeared to be locked. HOWEVER, I yanked on the lock and it came open as there isn’t quite enough clearance for the shackle to lock. I discovered that longer 3/16 shackle locks are hard to find. Have attached a photo of the lock that actually fits and works (Ace Hardware). One lock on the upper clamp down arm will secure both arms as the lower arm can’t be removed without removing the upper arm. The clamp down arms appear to be coated to prevent damage to your bike. I’ve tried a simple rag and ultimately settled on pool noodle pieces as a precautionary measure. I CAN NOT open my tailgate (regardless of whether or not the rack is fold up and in the bike carry position). If that’s a concern for you, then spring for the more costly titling version. My back-up camera still functions.
The Swagman XTC-2 platform bike carrier arrived very quickly from etrailer and in good shape, the actual carrier box is inside another shipper box, which I'm sure helped with its condition. Assembly was relatively quick and painless, even though the instructions could be a little more thorough. Installing the carrier on the back of our Jeep Patriot also was quick, it helps to have an extra ratchet & 3/4" socket laying around for just this purpose. Installing the bikes takes a little patience and trial and error the first time you try and put them on the carrier. It's easy enough to adjust the wheel holders to fit the wheelbase of your bikes, but for us at least, the challenge was trying to swing the vertical support bar up into position after putting on the first bike (closest to the Jeep). We couldn't angle the bike enough toward the Jeep to have the bar clear the bike. We learned that the easiest way to secure the first bike was to remove the ratcheting frame hooks altogether, put the bike in the carrier, swing up the vertical support bar, put in the pin, and then slide one of the frame hooks down on the bar. The outside bike is much easier because you can set the bike in the carrier at whatever angle you need, not being limited by the back of the vehicle. One thing we did to protect the bike frames was to use some foam pipe insulation as cushion between the frame hook and the frame (see pictures). Once you get a system for installing the bikes, it is very quick to load/unload them. The rack seems to be well made and doesn't wiggle excessively when traveling. All in all a good product for a good price, would definitely recommend it for anyone looking for a platform bike carrier.
# 9
Curt Clamp-On Bike Rack for 3 Bikes - 2" Ball Mounts
This is the best product online. I had to do a few adjustments to make room for the clamp on the trailer hitch. The particular ball hitch I had had a reinforcement welded to the ball which I had to have a piece taken off. Once it was filed down the clamp worked like a champ. Now I have a $200 bike rack that I purchased a year ago that is obsolete. The product arrived early and in good shape. I would definitely buy this bike rack and use this company again!
Needed a bike rack for our cross country RV trip last year for three bikes. I did not want to put anything on the car we were towing and the Curt clamp on bike rack fit our situation perfectly. The rack was easy to install and the bikes were safely carried 5956 miles over 25 days with no problems.
# 10
Swagman Trailhead Bike Rack for 3 Bikes - 1-1/4" and 2" Hitches - Tilting
Draw-tite Sportframe Trailer Hitch Receiver Class I - 1-1/4 Swagman Trailhead 3 Bike Rack - Tilting The Draw-tite Sportframe class 1 trailer hitch and Swagman Trailhead 3 bike rack were ordered for a 2017 Honda Fit. The online order and shipping went just as expected. The trailer hitch and bike rack are very heavy duty. I recommend watching the trailer hitch install video before installing, whereas the video is very helpful. The bike rack has triangles that you can rotate to find the best fit for your bicycle's frame. The rubber straps are thick and secure the bicycles when you pull them tight. This bike rack will stay on the vehicle for 6 months each year. The tilt feature and folding arm feature are must haves for a smaller hatchback. I am pleased with this purchase, it appears to be good quality and good value.
Just as advertised. Sturdy and solid. Folds at both the top and bottom sections for easy storage. The tie downs are well positioned and minimize bike movement. Can't wait to get on the road with it.
# 11
Swagman Trailhead Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Tilting
etrailer has the best pre- and post-sales customer service I've ever seen! I started out not knowing anything about hitch-mounted racks. So I wrote to etrailer telling them about my car and type of hitch I was about to have installed. Samuel wrote back with lots of great information tailored specifically to my car. He even included a photo that looked just like my 2017 white VW GTI with a hitch and rack installed. Okay something of a coincidence. But the rest of the assistance I got from the crew at etrailer was just as prophetic. I went into this a novice and came out knowing lots more about hitches and racks and finding the rack best suited to my situation. I have a small car, a class 1 hitch and a heavy mountain bike. I got exactly what I needed. As to the Swagman rack itself, it works fine. If I had a different situation I would probably buy a platform rack as they are easier to load. There's no reason to buy a bike rack anywhere else.
First off, thanks to Jason T. or "Troop". The exemplary customer service he provided is rare these days. Troop made several calls to the various manufacturers to ascertain which bike rack would afford me the most ground clearance as my new VW Golf sits low to the ground and my old bike rack frequently scraped the ground when I went up even a slight up hill grade. His efforts paid off as he found me the best bike rack for my car, the Swagman Trailhead 2 Bike Carrier. It sits up off the ground just high enough that it doesn't scrape on my driveway. It is also sturdy and holds my bikes securely. And, the delivery was amazingly fast. I had my rack in about 2 days! Note to Troop, see my Pittsburgh Pirates Logo on my bumper in the attached pictures? Pirate Fans persevere! The Bucco's will be coming after your Cardinals this year! Thanks again Troop!
# 12
Swagman Tailwhip Tailgate Pad for Mid-Size Trucks - Up to 4 Bikes - 54" Wide
Once again, etrailer delivers. Great product, and they always makes sure they fit!
Very satisfied with this product! It is plug & play out of the box, it takes 1-2 minutes to install, and it fit my Honda tailgate like a glove. The cover is lightweight yet fully protects my trucks finish. The Swagman is an excellent value.
# 13
Thule EasyFold XT Bike Rack for 2 Electric Bikes - 1-1/4" and 2" Hitches - Frame Mount
I purchased the rack and receiver hitch a year ago. Installation of the rack was made simple with the installation video that was specific to my vehicle (2020 Honda Accord). Literally took less than an hour start to finish. Only tool that I needed to buy was a torque wrench, which was about 20 bucks. It did require a very small cut in the plastic bumper that was accomplished easily with a keyhole saw. There was no drilling or other significant issues. The rack itself is awesome! My wife and I have two Lectric XP3 bikes. They weigh about 65 pounds each with battery. When we travel I revome the batteries to save a bit of weight. I have made two cross country trips (over 6000 miles) with this rack and have never had an issue. Literally every gas stop or hotel stop someone asks me about the rack and bikes. It really is that nice. My wife usually scolds me because we lose a 1/2 hour of travel time each stop to visit with complete strangers:) The rack is easy to install and remove on the receiver hitch. The lockout feature works great and gives a great deal of peace of mind. The bikes are easy to load. I don't use it, but there is a ramp that could make loading the bikes easier if a person couldn't lift the bike onto the rack. There are two arms the lock onto the frame of the bikes similar to the receiver hitch. Once locked down the bikes will not move. I would recommend ordering the longer ratchet staps if you have fat tires. I think they cost around 20 bucks but the longer straps allow for a little more flexibility in arranging bikes on the rack. I would strongly recommend this product and this company.
This product arrived in perfect condition in a sturdy box and arrived as expected. The description and photo were perfect. I am only 4'11" and I can lift and put this carrier on the hitch on our vehicle. It folds up which makes it easy to install. My husband did the minor assembly. We are impressed with how securely the rack is and comes with a ramp to help ease the bike onto the rack without lifting. Also, the rack can be tilted so the back hatch of the vehicle can be accessed without taking off the rack from the car.
# 14
Thule GateMate Pro Tailgate Pad for Full-Size Trucks - Up to 7 Bikes - 53" Wide
Very sturdy and well made. Great for a barrier between bikes and tailgate so it is not scratched. The camera flap is a plus so the rear view camera is accessible. No issues a year after purchase. Fits a 2014 Chevy Silverado 1500 and 2022 RAM 2500 equally well.
It has 7 different areas to strap bicycles down but there is definitely not room to strap 7 bikes down from what I can tell. The straps were a little tricky to feed under the tailgate and pull up at the same time with only one person. Overall it works pretty well but it appears to only have enough room for 4 MTN bikes.
# 15
Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
This bike rack works great for our 2 Lectric 2.0 e-bikes. We mount it on our 2019 Honda Ridgeline. It folds up nicely when it’s on the truck and we are using our bikes. The locking mechanisms work well also. I contacted support for a smaller hook arm to clamp B over the bike frame. They knew exactly what I needed and shipped it - no problem.
We love this for our E- Bikes . My husband said once he figured out the parts assembly was straightforward . We used the rack for our RV and it was perfect . Very sturdy and adjusts easily to our bikes . We are very pleased with this rack and would recommend !
# 16
Yakima EXO Swing Away 2 Bike Rack w/ Enclosed Cargo Carrier - 2" Hitches
Installed on 2017 Transit 350HD. First order on etrailer and the experience was great; really fast shipping and great communication. I was surprised to see it picked and shipped so quick so late in the day, especially for how big this is. It comes in 4 boxes; one giant one and 3 moderately huge ones. The Yakima EXO system is top notch, great construction. Excellent fit and finish, and pretty easy to assemble. Read the instructions and follow each step and you'll have no issues. I have a bad back and was able to assemble myself, the heaviest part is the swing away hitch - if you can lift about 40-50 pounds it is going to be easy to assemble without any help. I went slow and it only took me about 30-45 minutes. Tips - the bike rack portion it's not super clear that the rails should not be tight when you put the upper bike rack on. Just set everything in place and it will make getting the bolts through easier. Pros - it's as advertised. Super sturdy, no shaking/rocking, easy to use. The people who designed this system should be high fiving themselves, it's great. Cons - none really other than one minor customer experience gripe - you're given enough lock centers to re-key multiple Yakima EXO accessories, I think 4 are included...but it does not come with a master key for removing the lock center. You'll need to buy this separately or do like I did and make your own. Considering they put the effort into including replacement lock centers and give you every tool you'd need, it's a weird oversight. That being said once you replace the lock center on the cargo carrier you only need 1 key for all of the locks on the system which is awesome. Ford Transit specific issue I ran into: When the swing away is open there is a safety latch that holds it open so it will not fall closed on you. This gets in the way of the passenger door opening. But if you remove this (at your risk) you can open the passenger door fully and if you rotate the upper shelf you can even open the door entirely against the side of the van. Also it will 100% block your camera and license plate if it's door mounted. Absolutely stoked on this system. The cargo box is awesome with internal tie downs and taking it apart to store it in the garage only takes a minute or two. I love how easy the cargo box indexes in place. Every aspect of it has been super satisfying to play with.
I'm always impressed with the speed of getting shipments from etrailer. Of course the Yakima product quality is great, I think the service at etailer is what keeps me coming back.
# 17
Hollywood Racks Destination Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
The Destination bike rack works perfectly on my 2020 Pacifica and I have clearance going over speed bumps! I recently upgraded my bike to a Trek step through which hung too low on my old Thule rack no matter how the cross bar adapter was adjusted. Problem solved!
I realy like how it holds my bikes securly in place. I also like that (without the bikes) I can open and close the hatch on my 2014 Hyundia Santa Fe. I have a 2" receiver on my car. We went away for a long weekend from CT to VT and had no issues with it holding my bikes. Would definetly recomend.
# 18
RockyMounts MonoRail Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
At age 75, I have purchased many bike racks over the years…..this one has no equal in loading and unloading…
This rack is really, good. The only thing i add to make it better is small strap that holds the front wheel to the front wheel bracket. I never had a problem with it, but i like to make sure it is secure. It is a solid bike rack and worth every penny. I would buy this over the Kuat version any day.
# 19
Hollywood Racks Trail Rider Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
I looked at a LOT of bike racks, but when I saw the product video for this Hollywood rack and it was holding the bikes rock solid, no loose bouncing anywhere, I decided to try it and I haven't been disappointed yet. It is solid in the mount, it holds the bikes securely and the locking bars are a good deterrent to anyone wanting a quick steal. I don't leave mine on the car all the time, but so far in the weather here in Florida, it's holding up nicely. Add all this to the great price and customer service from etrailer.com and it's a big win for the average consumer. Thanks, etrailer!
I was impressed with this bike rack from the minute I unpacked it. The assembly was simple & straight forward. I looked at quite a few bike racks & for the price point this product was hard to beat. It is well designed & the keyhole pins make it easy to remove & fold up when not carrying the bikes. The locking hitch pin & locking frame bars are convenient and fairly secure. I will add my cable lock to make the bikes even a little more tamper proof. So far I’m very happy with this his purchase. Now the test of time!
# 20
Inno Tire Hold Bike Rack for 1 Bike - 1-1/4" and 2" Hitches - Tilting
Before I purchased I confirmed with both Etrailer and Inno that this rack will fit a class 1 hitch. Inno even prints class 1 in their directions. The INH120 (2-bike) does not. It was a yes from both sources. The pin they use DOES NOT fit the hold for a class 1. In fact they use the same proprietary pin system for the 2 bike version. NOT GOOD!!!!
This is my third bike carrier in over 16 years. There was nothing wrong with the others. I got a new SUV and a new E-bike and wanted a new hitch for one bike. The Inno INH110 was perfect. It was a little strange at first in the way the rack was secured to the receiver but after trying it, It was a good feature. I recommend this hitch. m It very robust and I can see many years without issue.
Thule Hitch Bike Racks Review - 2000 Dodge Dakota
Today on our 2000 Dodge Dakota, we're going to be doing a test fit to the Thule Vertex. This is going to be your hanging style 4 bike rack. This rack comes with an 1 1/4 shank for your class 1 and 2 hitches as well as the 2 inch adapter for your class 3 hitches. It does have the tilting feature as well and it will be part number TH9029XT. Let's go ahead and get it fitted onto our 2 inch receiver. The nice thing is that it does come with a handle on the backside to, it is easy to lift up and handle with one hand.
What our customers are saying:
"I ordered a trailer hitch and a bike rack carrier the order was shipped with in three days. To put the hitch on only took about 30 mins. only had to drill two 1/2 holes. fit like a glove."