# 1
Flash Secure Adjustable 2-Ball Mount w Chrome Balls - 2" Hitch - 6" Drop, 7" Rise
Very strong, easy to install and very secure. Yes a bit pricey, but well worth the money. I did notice there was what I thought was an unusual amount of play in the receiver. I called etrailer and Marcia was so very helpful and very concerned that I may have received the wrong product. She even called the manufacturer and found out what the changes that were made by the manufacturer which made the pictures incorrect. My hat is off to Marcia and all the folks at etrailer
ball mount fits loosely in the receiver so that the pins that extend out from the ball mount shaft through the holes in the receiver don't extend out far enough, for my liking. This is because since the ball mount shaft has so much play, it will shift to one side. Then, the pin on the other side does not extend all the way out of the hole so that it is not flush. True, i am being paranoid. However, i imagine a case like a crash where enough force could pull the shaft out from the not fully extended pin side to release the trailer to wreak more damage. I would just feel more secure if the pins went out further through the receiver or the shaft was not so loose. Otherwise, i really like the product a lot... enough to give it four stars... :o)
# 2
B&W Tow & Stow 2-Ball Mount - 2" Hitch - 7" Drop, 7-1/2" Rise - 10K - Black
Using this hitch on my Expedition and LandCruiser. A standard hitch caused my 12 ft utility trailer to not ride level when towed behind either truck. Since my trucks have different ride heights, the B&W hitch allows me to get the perfect drop for each truck. Trailer responds much better to road issues level as opposed to angled behind the truck. Additionally, its rating exceeds both of the trucks’ towing capabilities, so I have the hitch I need for the future as I have plans for a heavier trailer down the road. Quality and fitment of the hitch is excellent.
hitch worked well for my small utility trailer behind my new full size truck. Only possible down side is the ball I'm not using does sit somewhat low and could in certain circumstances hit a kerb or other bump. Haven't had that issue and think it's unlikely, but it is possible. Note I need the ball mounted on the lowest seting, 7" drop to work with this trailer on this truck
# 3
Curt Multi-Ball Adjustable Ball Mount for 2" Trailer Hitches
Picked up my teardrop in ABQ on 2/17/23, and the Curt ball mount lined up perfectly with no drop/rise, and the extra length gave clearance for my rear door mounted spare tire. This mount is a beast, and the "overbuilt" nature of it gave me confidence that my Bronco would tow the teardrop easily. I also got the Curt Echo wireless brake controller, which synced easily to my phone and was easy to install, set up, and use. Overall a great towing experience, thanks to etrailer and Curt!
Very versatile - can use it on both my vehicles that have very different hitch height. Clean welds, super solid. Weighs a LOT!
# 4
B&W Tow & Stow 2-Ball Mount - 2" Hitch - 5" Drop, 5-1/2" Rise - 10K - Black
I wish I would have bought one of these years ago. It would have saved me from buying 4 different height hitch receivers. I have a boat trailer that requires me to mount this hitch upside down to get about 2.5in of rise. On the flip side is my utility trailer that requires a 2 inch drop. The kicker is that when I load the truck down with gear and people or load the utility trailer up really heavy, this hitch allows me to kick the ball up or down a notch to keep the trailer level. Also if you ever rent heavy equipment most of the trailers they use will have 2 5/16 ball, so I just flip the ball and I'm in business. Build quality and finish is excellent. I don't keep the mount on all year long but with some judicious use of grease this thing hasn't shown any rust over the past year of use. I am currently using this on a stock GMC Sierra 1500 and I really could have gone with one size down on the hitch drop/rise, but I figured if I ever bought a 3/4 ton truck or a friend with one ever needed to borrow the hitch it would have enough drop to work with that application as well. As it stands the 5in drop isn't too long to cause clearance issues with a half ton GM truck. For those of you who are wondering about thieves making off with the ball mount - the design of the tow and stow is such that with all the pins removed and the hitch installed on the vehicle, it is not possible to rotate the ball mount off the receiver. Especially if you mount the receiver using the inner most mounting hole. All that is needed is a locking hitch pin and the whole setup is secure. I've attached a picture of the hitch installed on a 2015 GMC Sierra 1500 4x4 for reference.
I am so absolutely thrilled with my trailer hitch! etrailer made my purchase extremely easy. I have never bought a trailer hitch before, but I was able to pick the right size and the capability that I needed, based upon awesome product videos and reviews. Your company has exceeded my expectations of customer service and prompt product delivery. I applaud you and your team!
# 5
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
Makes for a great hard-core dirt road set up with a 3000 pound trailer, in conjunction with the Curt rocker ball, Towing with an F150 over many miles of washboards, down through washes where the road was washed out, etc. Really makes for a gentler set up on the equipment in the trailer and the truck. Thanks a lot E-trailer!
My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks
# 6
Convert-A-Ball Ball Mount for 2" Hitches - 6-3/4" Rise, 8" Drop - 10,000 lbs
I use this hitch when I pull my horse trailer to make the stop/start transitions as smooth as possible for the horses in the back. It works great. I also love that its a category IV hitch. Really heavy duty. My truck sits pretty high, and the amount of drop - 8" is perfect. I never worry about hitch failure travelling with my horses - they're a heavy load, and any failure would be a disaster. E Trailer provided excellent service, and their shipping to Canada was prompt and hassle free. Way to go guys, keep up the great work!
I have a 2012 GMC Sierra HD with a 12" suspension lift. I recently purchased a ball mount hitch with 8" inch drop for our 36' RV trailer and it worked great. It took 3 days for the hitch to get to me. Great service from e-trailer.
# 7
Rapid Hitch Adjustable, Aluminum Ball Mount Kit w/ 2 Zinc Balls - 10" Drop, 11" Rise
Hello The hitch works great as viewed in the enclosed pictures. If inverted it hits the bumper, of my Dodge 2500. The section that goes into the receiver is about 1/2" too short and hits the bumper. I have not tried it on my other vehicle to see if this is a problem. Kind Regards Leon D
A VERY nice piece that will set your mind at ease. Easy to adjust height. The ONLY thing I wish is there was an option to have different sized ball combinations. I mainly use 2" and NEVER use a 2 5/16"(or whatever the larger size is) and would prefer to have a 1 7/8" on the other side.
# 8
Rapid Hitch Adjustable, Aluminum Ball Mount Kit w/ 2 Greaseless Balls - 5-1/2" Drop
I ordered my AM3405 and was amazed how quickly the etrailer team responded with not only my order confirmation but the fantastic follow up when it was shipped and delivered. I highly recommend etrailer and will order from them again. The product showed up in great shape and I am very happy with the quality. One recommendation would be to order two of the locking pins. One for the receiver and one to lock the ball mount to the unit. You will see by my picture I resolved that issue with a pad lock but the locking pin would have been better.
# 9
Convert-A-Ball Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 10,000 lbs
Good, very solid ball mount with just the extra rise I needed, 2 3/4", to get level trailer and good clearance for the trailer jack. But excessive shipping charges from etrailer, $[XX] for an $[XX] purchase. Found out to my cost later that [online vendor] would have shipped for free.
As a full-time RVer, e-shopping is very important for us. etrailer was the right place to shop. Right product, delivered on-time for a great price. You beat the local discount RV store by $25 including shipping. At the same time, I had another outfit send me a clearly inferior product to the one they displayed. Said they would e-mail a pre-paid shipping label for the return (didn't) and tried to put the blame on Amazon. Thanks etrailer for a great experience !
# 10
Cushioned Ball Mount for 2" Hitches - 4-3/4" Rise - 6" Drop - 10,000 lbs
All of the items arrived on time and not damaged in any way. Excellent quality products.
Parts came fast and they worked great took the band out of the trailer. Thanks for fast service.
# 11
Rapid Hitch Adjustable, Aluminum Ball Mount Kit w/ 2 Zinc Balls - 5-1/2" Drop
I pay to receive the product in good condition, my hitch ended up being damaged, I don't know what type of packaging this was, they are supposedly a waoooo site, I ask for my return label and my refund, I
Works flawlessly. I was very excited the day I got home and my Rapid hitch was on the front porch. It came in nice box and was packaged very well. I opened it up and unpacked my rapid hitch and I was very impressed with the quality and precision of this hitch. All of the machining was PERFECT and everything fit together right. I put it in my truck right away. Going down the road with the trailer on and off there is absolutely no rattles, clunks, or jolts. I also love how everything is aluminum or stainless steel, NO RUST. I wish I could've gotten the greaseless model but my boat is too heavy. My only complaint is that it doesn't come with locking pins. With a hitch this expensive I really wish it came with them. Do yourself a favor and order them with your rapid hitch so you don't have to pay for shipping in the future. Other than that great product and I believe it will outlast me.
# 12
Flash Secure 2-Ball Mount w/ Chrome Balls - 2" Hitch - 10" Drop, 11" Rise
I have not had a chance to use the ball mount yet but it is easy to use and fits receiver with no issues. I recently purchased a Curt class V receiver that is installed below my OEM receiver. With the drop installed in the Curt receiver in the upright position, the back of the ball mount comes very close to the bumper on my 2011 Ram 2500 crew cab. I will see if there are any contact issues when actually towing and revise my review, if necessary.
So far so good. Only had the hitch for 2 wks. Upgraded my tractor hauler truck and trailer so why not the hitch as well. Looks to be very solid construction. As to the locking mechanism I am pleased I chose the barrel keys. Easier to keep clean (dirt roads) and spending this $$ on hitch I lock the design. Other hitches have been stolen when they beat the lock bar off the receiver.
What our customers are saying:
"very easy to shop"