Best 2022 Ford Expedition Trailer Hitch Ball Mounts

Coming in at about 45 pounds, the D900 Curt Multi-Ball Adjustable Ball Mount is a BEAST! I purchased for use with my '08 Expedition towing either a small utility trailer w/ 1 7/8" ball or my DooLittle Bullitt cargo trailer w/ 2" ball. I needed 5 inches of drop (at least) for both. This is just about the only economical mount in which to accomplish this. Most if not all two ball mounts are 2" and 2 5/16" balls. Many reviews comment on the length that this mount sticks out and initially that was a concern of mine. Please see the Q&A of the D900 product page to address those issues. Short story: A hollow/tubular extension shank of (about or greater)15" reduces vehicle hitch capacity by 50%. The D900 shank and other components are SOLID steel. No reduced capacity. Specifically in my case; this extra length will allow me some personal maneuvering room when hooked up to the DooLittle and raising the lift gate of my Expedition. Clearance between raised lift gate and cargo trailer was about two inches using my old shank, and I should about double that. The anti-rattle tightening bolt is a nice touch. This is my first Etrailer purchase, but not my last.

VERY sturdy piece of hardware here. I was worried it might be a little flimsy piece of metal. Not so, this is a substantial hunk of engineering and I feel safe putting anything on the back of my Expedition! Fully adjustable and easy to install, just like it says!

The product is good but a bit tideous and after installing it my bracket fell and it was a pain to get replace it support made me buy the replacement pieces and the bracket didnt come with just the bolts, and at the end they told i have i had to buy the whole unit because based on their system my truck didnt have issues with installement and the manufacturer didnt supply that bracket cause it special order so in general i dont recommend in my choice better to get it welded.

Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.

The hitch was received quite quickly and is even nicer than the picture shows it to be. I pull different trailers and it was always a hassle to have the correct hitch. I also like that they did a follow up call when I requested the item be shipped to an address other than my billing address. We are all concerned about credit card fraud. I will definitely order from them again!

I've used the hitch over the last year on several trailers and loads. The adjustability made towing a much better feel and ride over a fixed hitch that at times not the greatest. I see no wear, very easy to adjust even once coupled to the trailer and finding the trailer needs to be leveled better.

This is a beast of a drawbar, solid forged steel & well finished. It's also very heavy and E-Trailer needed to ship 3 times because the first two broke out of the box they were packed in. (Someone in the USPS has a couple nice draw bars.) Fortunately the 3rd effort was much better packed in a reinforced box and was successfully delivered. E-Trailer customer service was exemplary in resolving the shipment issue & I will definitely shop with them again.

I had a great experience ordering from you. Your organization kept me completely up to date with the order & shipping process and delivered the exact products I ordered. Attached is a photo of the 16,000 lbs capacity hitch and 30,000 lbs 2 5/16 ball you sold me in use. The boat and trailer total about 12,000 pounds. Thanks again.

Great Product

Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.

I purchased Curt's 6" drop ball mount for my 2012 Jeep Wrangler Sport which is not lifted but has 32" tall tires. The utility trailer I plan to purchase recommends a 12" tongue/ball height for level towing. The Curt 6" drop ball mount places my tongue/ball height at 13.5" which is acceptable. The bottom of my tow ball mounting nut is now 12" above the road surface. Plenty of clearance for safe towing. I'm very pleased with the quality and functionality of my Curt ball mount. I'm looking forward to purchasing a utility trailer soon. I think it will tow very nicely using my Curt 6" drop ball hitch.

I bought this on my knowledgeable brother's advice - he gave me the exact order number and link to buy from etrailer! I had it installed locally, without complications. I use my truck mostly to haul my horse or my friend's two donkeys in my 14-foot stock trailer. I have no complaints, the hitch does what it's supposed to do.

This hitch is a very handy addition to my toolbox! I work for a county road department, and I’m always pulling different trailers to and from job sites. I can switch from a 2 5/16” ball hitch, to a pintle hitch with the flip of a lever! Thanks B and W!

As good as it gets. Made in U.S.A. Quality is perfect, functionality best in its class. Exactly what I was looking for in a Pintle- ball combo. Don't hesitate you wont be disappointed. Etrailer was great from first contact to fast delivery. Thank you

This worked very well for our needs, allowing us to attach a 4-bike carrier and a cargo trailer to our Expedition.

We sold our small motor home and purchased a small travel trailer. This hitch provided a perfect solution to how to use our bike rack while towing the trailer. It even allows room for the pickup tailgate to be lowered without removing the bikes from the rack. The hitch is very hefty with a high weight limit - plenty for the GVW of the trailer (7,000#) plus 125# of rack and bikes.

Very happy with this ball mount - provides just the amount of drop we required for a level tow of our GeoPro travel trailer by our RAM2500. Plus, the extra length not only allows a tighter turning radius, but also allows us to lower the truck tailgate without having to detach the trailer. Huge improvement on all accounts for us compared to our prior setup. The product is well built and I'm confident will provide us years of good use.

Your packaging it's lousy, package arrived with a receiver size hole in the end of box . Guess what the box was empty . This is the second time I have had problems with your company !

Everything, when I need something for my truck I always turn to etrailer. They make it so easy to get the product you are looking for. The quality of their product and the Customer service are the BEST! Thank you.

Great solid forged Ball mount!

Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.

I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.

Sooooo....you sent me a product that was somehow put together backwards and I cannot take them apart somehow the ballhitch is stuck on the male portion backwards and defies gravity and doesn’t need a pin to stay on(becaue thier is no where to put the pin in cause it’s backwards

Have done about 5k with this hitch, just once with a 4500lb camper but mostly with a 3000lb cargo trailer. The former in a highly raised position and the latter in the absolute bottom position. The hitch has worn very well and shows no signs of excess wear, save for the surface of the 2" ball, but it's not concerning. On a Jeep Grand Cherokee with a stock suspension, this seems to give the right balance of range of adjustment without dropping so low in the lower configuration as to scrape through dips, though it can still be done on very sharp dips with the hitch on the lowest setting. Overall, very pleased with it and love that it's lighter than steel and won't rust.

I did my research before ordering. I know exactly what I need and want. My boat trailer tongue weight is 750lbs so I went with the Gen-Y Torsion Flex 2" Hitch - 7.5" Drop/Rise 10k. (Works Best with 400-1,000lbs tongue weight). Also got the BEST price due to their 110% Price Match Guarantee.

It was well packaged shipping was great received it within a week installation was easy weighing only 73 pounds. It does affect the center back up sensors on a 2022 , 3500 long bed ram pick up.

Ordering was extremely easy and etrailer representative very helpful. Chedi also sent me videos that explained perfectly how to install. I don't usually leave reviews, but these guys deserve a good one. Customer service and products delivered were impressive.

This is a great all-purpose hitch. I've used it to mount a heavy-duty bike rack and a steel T-rack to carry a canoe as well as lumber. Most recently I hauled 5 x 8 cargo trailers full of plants, then furniture for a 600-mile move. It was simple to use, problem free, very strong and sturdy. Now that I live on some acreage, I see a trailer in my future, so this will get a lot more use. I drive a 2013 Tacoma, so this is a good size hitch at a good price with sufficient capacity for my needs. I do use a key lock for the hitch as well.

My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks

Makes for a great hard-core dirt road set up with a 3000 pound trailer, in conjunction with the Curt rocker ball, Towing with an F150 over many miles of washboards, down through washes where the road was washed out, etc. Really makes for a gentler set up on the equipment in the trailer and the truck. Thanks a lot E-trailer!

This still looks good with no slop easy to switch between the different ball.

VERY HAPPY, BUT STARTED TO SEE SOME RUST ON THE HITCH BALL AND ONLY USED TWO TIMES. THE VERSABILITY OF THE PRODUCT IS GREAT. OTHER THAN THE SMALL AMOUNT OF RUST ON THE BALL ITSELF, IM VERY SATISFY AND WILL BUY FOR MY OTHER TRUCKS.

The hitch and ball mount are excellent quality. My concerns are twofold. The hitch is so heavy that I had to take it to my mechanic to have it installed. Minor cost and inconvenience, but the hitch for my previous F-150 was just as sturdy, but easy to install myself (albeit with higher ground clearance). My concern about the ball mount is that the factory told me erroneously that it could not be reversed for a drop, so I returned it. This order is for the replacement after I was finally correctly told it could be reversed and how to do that. Ball mount would have been a 3 for that reason, and overall hitch and ball mount quality a 5. So I averaged them.

I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.

Great fit and finish looking forward to the first tow with it.

This is a must have for full-time trailer hauling. No ball grease needed. Easy to adjust for a level trailer, smooth towing. I increased my trailer tires to light duty truck tires (a little taller tire), for heaver loads & ease of mind to haul at 75 mph speed. This hitch allow me to fine tune the trailer ball height for best setup on my heavy duty Toyota Tundra truck.

Love these. This is my third one. Wouldnt pull a trailer with anything else. Trannys are expensive.

As a full-time RVer, e-shopping is very important for us. etrailer was the right place to shop. Right product, delivered on-time for a great price. You beat the local discount RV store by $25 including shipping. At the same time, I had another outfit send me a clearly inferior product to the one they displayed. Said they would e-mail a pre-paid shipping label for the return (didn't) and tried to put the blame on Amazon. Thanks etrailer for a great experience !

Awesome hitch, I use it on a 2003 Ford F-350 and 2005 Ford Expedition, so much nicer just carrying one hitch for any trailer I tow compared to having all different hitches to deal with and lug around

Works as it should. I enjoy not having to hunt for different hitches when switching trailers. So far no rust..