Most Popular Bolt-On for 2017 Forest River R-Pod Travel Trailer

My Jack arrived DOA. After installing it on my trailer, the Jack didn’t work. The manual crank handle came in handy because I didn’t have time to troubleshoot and repair it at the time. It was just a wire that was no longer connected to the switch but I have to tell you it was extremely disappointing to receive a brand new item that didn’t work. If it had worked out of the box, I’d give it a five star review. You should consider soldering and heat shrinking the wires to the switches or making the wires longer so they aren’t banjo string tight and putting the lug at a strange angle.

Great product and Trailer has great customer service. It's to bad that the shipping companies do not take better care with the items during shipping! will receive replacement parts to fix what was broken, but it causes lots of extra work for the customer. will have to take complete jack off to replace the broken motor cover because of shipping carelessness!! regards, Dan Ewert

Great product. works just fine. The problem I had was matching the mounting plate under my trailer. Apparently not a standard so I had to take it to a trailer manufacturer to make it fit.

They went on a custom made trailer build that’s not yet in service. Seem to function as advertised.

Quick shipping. I will be ordering more parts as I need them for our RV.

We replaced four badly worn 2500 lb jacks with these heavier 5000 lb jacks and are very happy with the quality of these new jacks. They arrived quickly and were a perfect fit. The construction is superior to the jacks we replaced. Your instructional videos were very helpful. Thanks for your excellent service.

One small part was missing from my Ground Control TT. Carol Korren expedited delivery of the missing part and the UPS truck pulled up at the moment I needed the part. Fantastic customer service!

This works great and has been the very best upgrade on any RV/Trailer I have every owned. I will never own another trailer that does not have this.

I should have got one years ago. I only use it when it's connected to the truck with the engine running. This I believe gives me full power. It has enough power to raise the trailer when connected to the truck to get the anti sway bars attached. Sure beats all that hand cranking.

The alternate power setup makes its slow rate of rise necessary which would be good if my lithium batteries went low. To avoid battery problems be sure to add an inline battery disconnect from the trailer power when using tow vehicle power. I simple added an inline fuse that could be removed should I need to use the tow vehicle power.

It installed very easy. For a 2500lbs jack, it seems a little light weight. It does lift the trailer but seems kinda wobbly because the post size is so small. Other than that it works as advertised. Thank you for getting it to me so fast.

I just installed my new JET-2500 trailer tongue jack in less than 15 minutes. The light and extend/retract work great. I was not sure if an adjustable drop foot is available for more length but do not think it is needed. This is second purchase, first being Equalizer hitch system which is also even better with electric jack. Etrailer exceeds customer expectations by follow up email and definite concern to keep their customers satisfied. Great Company! Thank-You Ron Williams

The powerhead is very large and extends forward, which has caused it to impact upon two different vehicles when backing the trailer. The power function is now useless, and I am using the manual crank to raise and lower the jack.

Sturdy jack, easy to install. We installed it facing to the driver's side so we can still put our tailgate down. Very powerful jack, only drawback is it is very slow.

Overall the product does exactly what it's intended for and works well. I however assumed that this would be a simple R&R for my camper and did very little installation research other that the video provided on etrailer' s website Sadly it did not fit. Not at all. I didn't take into account that have a double framed hitch toyhauler. The baseplate on the factory leg was a TRIANGLE.....this unit was ROUND. Also the primary shaft was thicker than stock and would not drop down into place I know modifying is frowned upon, but I found that ALL powered hitch legs I found have round mounting plates and it's not mentioned the leg tube is thicker than OEM? Since NOT having a power lift wasn't an option for this camper application...too heavy in the front when ATVS loaded to lift for setting the equalizer hitch tension bars, I proceeded to modify by cutting the rear rounded mounting base ... square. Took off about 1/2 inch. Then I took my metal Dremel sanding bit and increased the hitch leg hole diameter slightly. Took about 1 hr. Dropped it in. Wired it. Tested it. All good. If you can't post this I understand, but take note that some of your website descriptions may need to be enhanced. Thanks!

I ordered the Reese Bulldog 4000lb power tongue jack on 6/2 and received it on 6/6, my second order from etrailer and it came just as fast as the hitch that I ordered from them previously. The jack was characteristically well packaged so everything was received in perfect condition. The installation took a half hour, including hitching the trailer up to my truck and unhitching after the swap out. I did read the instructions quickly before starting and I would recommend that anyone doing the installation do so as well, just to avoid any hick-ups. Overall it was a very easy installation. Because of limited space I did have to mount the jack sideways, so I appreciate that Reese gave me that option. The one item that I did not finish was a permanent power hook-up. The power wire provided was too short so I will be putting a connector inline so that I can route the wire to the battery terminal.

Hello, Please see pics below of broken weld on jack. The jack was just installed and in use for about 7 days and noted the broken weld. Jack functions as described, however, we question the durability of the jack.

Definitely has the power I need however I can't open my tailgate when my camper is hooked up. 5 stars for power.

These are great jacks. I have 3 of them. The only reason I replace one was because I bent it. Let's not go there.

This jack was the perfect solution for my application. I have a new enclosed trailer that came with a manual crank and only a tiny battery to run the lights. I did not want the expense of having to buy and cable up a larger battery to just support the tongue jack. Took me 5 minutes to install this new jack using the three bolts that were already on my OEM jack. Now I just back up my truck, plug in the 7-way, and I'm able to move the tongue up and down as needed. Great!

I purchased this jack to replace my tired 10 year old camper jack . I ordered it at 10:00 AM Monday and as promised by Ian it was at my doorstep on Friday just in time for my weekend getaway . Installation was a breeze . I gave the product a 4 out of 5 for a few reasons . First , I was not able to see the manufacturer of the jack before receiving it . Which made name brand comparison pricing difficult . However I feel pricing was on target . Second , I feel that the jack should come with a battery terminal end connector and new mounting bolts with the hardware that was included . This didn’t pose any difficulty to me as I had hardware at hand but for some it will mean a trip or two to the hardware store . Third , once installed , at least with my truck and trailer , unless the truck and trailer are perfectly aligned and level the jack motor gets in the way of opening the tail gate . On first use I noticed it was much slower than my original but the strength made up for it . This jack had no difficulty or hesitation lifting my truck and trailer for load distribution and anti sway bar installation . I would recommend etrailer and this product . Time will be the final test of its durability .

Item arrived a day earlier & in good condition! & was a very easy install ,& is a upgrade from manual one that broke at the handle ,& this is a upgrade for my 2008 22'Airstream Safari! Can't wait for my next outing, Also I like that it comes with a backup manual hand crank in case you need it,& that it was a exact fit for my travel trailer,It's a complete package that needs nothing else.

This was a great replacement for our 4 year old Keystone Springdale trailer jack that bit the dust. Installation was easy and is much faster and quieter than our RAM jack that came with the trailer. I did sand down the paint on the contact points to make sure of a good ground then painted over what was exposed. I liked it so much I'll be looking at getting one for my large utility trailer.

The machine is great. The auto up and down make life easy I had trouble with my first one I bought. One of the wires on the controller was loose. It was promptly replaced and the other one has given me no trouble at all.

if I had to rate this upgrade in difficulty one being the easiest five being the hardest, it would be a one. Super simple. Take the nuts and bolts off your old hardware and install the upgrade in its place. I read some of the reviews were people were annoyed with the counter clockwise rotation and the bolt sticking out too far. I really didn’t see a problem with either. I know you’re not supposed to use a drill to extend and retract these but I always have. I suppose as long as you’re not torquing the heck out of the adjustment screw you shouldn’t have any problems. I always put a small flat 2 x 6 piece of wood under the foot of each one of these. It seems to add quite a bit of stability.

The jacks themselves have worked great, they keep the trailer level and solid during our concession events. I just had them mounted to the trailer so I don't have to put them in and out at each event. The jack handles leave a bit to be desired so I use a 20v drill w/ a 3/4" socket to run them up and down.

This Bulldog replaced an Atwood jack on our Lance 1575. The Bulldog is quiet, but there is a fair amount of play between the inner and outer tubes. It feels unstable even when fully retracted. This wasn't the case with my old Atwood jack. If I had known this, I would have gone with another brand. I bought the Bulldog based on the reviews and the warranty, so I was surprised that there is so much wobble in it.

Installation was quick and easy per the instructions and eTrailer video. One of the few times I've had something "bolt right in/on" LOL. It has worked flawlessly in the time that I've been using it. The only drawback, and it is a small issue, is that it is easy in the heat of battle to bump the light switch ON and not see it in the daylight. One just needs to be careful or use a bit of tape to secure light switch OFF until needed. Another great product from etailer.

Ordered a power stabilizer jack for my 2012 Jayco fifth wheel in 2023 , easy to install the item myself , stabilizer working great , will buy future items at this site , thanks

The stabilizer works well. I would buy it again

Perfect! My weld for rear bumper was in the way of the bracket, so I just swapped 1 bracket each side from the old jacks, jacks were same size but rated lighter weight. Thanks for quick delivery! Always like the tutorials and pictures.

The box was a bit beat up when it arrived, but hopefully everything is intact.

This is what I needed. I Wanted a little more lbs. of lift so I could lift my truck for weight bars and such. I have a 2014 Rockwood A Fram and needed the mounting holes to line up. After some research, I found Stromberg jet-3755 worked perfectly. I have used it for a year now and no problems. Easy to set up and use. Thank you etrailer

Item arrived a day early. Installation was easy. Jack works smoothly. 3500# rating is 500# better than the factory installed jack.

Absolutely a breeze to replace the old jacks. They hold the trailer up with ease.

These stabilizers are much better built that the ones that came on the trailer. The lift components are sturdy and the screw shaft is bigger diameter.

I mounted this Stabilizers Jacks to the back of a 4x8 utility trailer. I use the trailer to haul my Honda ATV to MotoAmerica motorcycle races. Once the ATV is removed I lower the jacks and mount my tent inside the trailer. These stabilizers allow me to safely move around in the tent without fear of the trailer tipping.

Does not ratchet up, a pin must be manually inserted. It only came with one 6" long pin, which needs to be cut in half to make these stands functional. This is more like a folding jack stand, but the pin is not connected to the stand with a lanyard. I will be cutting the bar in half and welding a washer to hold it in place. I will also need to add a lanyard to it so I don't loose it. I would not recommend this product, but I have not found a better substitute for my application.

The product works as designed. Easy to install and I have used it approximately 20 times in the last year. The storage for the 7 pin connector and safety chains are a great option. Keeps things nice and tidy when unhooked. I highly recommend this Jack.

Perfect fit and operates very quietly and with abundant power for my 27 foot Lance travel trailer. The Jack-It Lippert bike rack mount fits perfectly over it, and the manual emergency jack crank fits within the tube of the Jack-it if the need arises. Also, the handy ring for stowing the trailer chains and receptacle for stowing the 7-way connector is a nice feature. Very happy with my purchase, and etrailer is fantastic, as usual!