Best 2017 Forest River R-Pod Travel Trailer Camper Jacks

My Jack arrived DOA. After installing it on my trailer, the Jack didn’t work. The manual crank handle came in handy because I didn’t have time to troubleshoot and repair it at the time. It was just a wire that was no longer connected to the switch but I have to tell you it was extremely disappointing to receive a brand new item that didn’t work. If it had worked out of the box, I’d give it a five star review. You should consider soldering and heat shrinking the wires to the switches or making the wires longer so they aren’t banjo string tight and putting the lug at a strange angle.

Great product and Trailer has great customer service. It's to bad that the shipping companies do not take better care with the items during shipping! will receive replacement parts to fix what was broken, but it causes lots of extra work for the customer. will have to take complete jack off to replace the broken motor cover because of shipping carelessness!! regards, Dan Ewert

Great product. works just fine. The problem I had was matching the mounting plate under my trailer. Apparently not a standard so I had to take it to a trailer manufacturer to make it fit.

They went on a custom made trailer build that’s not yet in service. Seem to function as advertised.

We replaced four badly worn 2500 lb jacks with these heavier 5000 lb jacks and are very happy with the quality of these new jacks. They arrived quickly and were a perfect fit. The construction is superior to the jacks we replaced. Your instructional videos were very helpful. Thanks for your excellent service.

This was my second order with etrailer and I have been pleased with the service. Items are shipped quickly and order was accurate each time. The products are high quality and work as described.

I should have got one years ago. I only use it when it's connected to the truck with the engine running. This I believe gives me full power. It has enough power to raise the trailer when connected to the truck to get the anti sway bars attached. Sure beats all that hand cranking.

The alternate power setup makes its slow rate of rise necessary which would be good if my lithium batteries went low. To avoid battery problems be sure to add an inline battery disconnect from the trailer power when using tow vehicle power. I simple added an inline fuse that could be removed should I need to use the tow vehicle power.

This sure beats hand cranking! We are in our 70s and ANY help like this electric jack makes going camping better!

I just installed my new JET-2500 trailer tongue jack in less than 15 minutes. The light and extend/retract work great. I was not sure if an adjustable drop foot is available for more length but do not think it is needed. This is second purchase, first being Equalizer hitch system which is also even better with electric jack. Etrailer exceeds customer expectations by follow up email and definite concern to keep their customers satisfied. Great Company! Thank-You Ron Williams

Sturdy jack, easy to install. We installed it facing to the driver's side so we can still put our tailgate down. Very powerful jack, only drawback is it is very slow.

Showed up a day early. Looks like a perfect replacement.

Overall the product does exactly what it's intended for and works well. I however assumed that this would be a simple R&R for my camper and did very little installation research other that the video provided on etrailer' s website Sadly it did not fit. Not at all. I didn't take into account that have a double framed hitch toyhauler. The baseplate on the factory leg was a TRIANGLE.....this unit was ROUND. Also the primary shaft was thicker than stock and would not drop down into place I know modifying is frowned upon, but I found that ALL powered hitch legs I found have round mounting plates and it's not mentioned the leg tube is thicker than OEM? Since NOT having a power lift wasn't an option for this camper application...too heavy in the front when ATVS loaded to lift for setting the equalizer hitch tension bars, I proceeded to modify by cutting the rear rounded mounting base ... square. Took off about 1/2 inch. Then I took my metal Dremel sanding bit and increased the hitch leg hole diameter slightly. Took about 1 hr. Dropped it in. Wired it. Tested it. All good. If you can't post this I understand, but take note that some of your website descriptions may need to be enhanced. Thanks!

Easy installation to replace the manual trailer crank. This model is powerful and works well. It has the ability to be rotated 90 degrees so its sideways. The advantage being is that my GMC 2500 AT4 truck tailgate can be lowered with the trailer connected using it in the sideways mounting position.

Hello, Please see pics below of broken weld on jack. The jack was just installed and in use for about 7 days and noted the broken weld. Jack functions as described, however, we question the durability of the jack.

Definitely has the power I need however I can't open my tailgate when my camper is hooked up. 5 stars for power.

These are great jacks. I have 3 of them. The only reason I replace one was because I bent it. Let's not go there.

The CargoBuckle G3 ratchet tie-down straps and 45 degree mounting brackets worked great. Makes loading and unloading a breeze.

Web site easy to use. Trailer jack came in quick. I like not having to wonder if my online order is going to ship or get delivered. Every time i order from this company i get an email they received my order. I get an email that it shipped. I get an email that it was Delivered. Now days its common to place an online order and you take a chance of not knowing if you going to get anything. I recommend this company.

Item arrived a day earlier & in good condition! & was a very easy install ,& is a upgrade from manual one that broke at the handle ,& this is a upgrade for my 2008 22'Airstream Safari! Can't wait for my next outing, Also I like that it comes with a backup manual hand crank in case you need it,& that it was a exact fit for my travel trailer,It's a complete package that needs nothing else.

This was a great replacement for our 4 year old Keystone Springdale trailer jack that bit the dust. Installation was easy and is much faster and quieter than our RAM jack that came with the trailer. I did sand down the paint on the contact points to make sure of a good ground then painted over what was exposed. I liked it so much I'll be looking at getting one for my large utility trailer.

The machine is great. The auto up and down make life easy I had trouble with my first one I bought. One of the wires on the controller was loose. It was promptly replaced and the other one has given me no trouble at all.

if I had to rate this upgrade in difficulty one being the easiest five being the hardest, it would be a one. Super simple. Take the nuts and bolts off your old hardware and install the upgrade in its place. I read some of the reviews were people were annoyed with the counter clockwise rotation and the bolt sticking out too far. I really didn’t see a problem with either. I know you’re not supposed to use a drill to extend and retract these but I always have. I suppose as long as you’re not torquing the heck out of the adjustment screw you shouldn’t have any problems. I always put a small flat 2 x 6 piece of wood under the foot of each one of these. It seems to add quite a bit of stability.

Definitely a heavier duty version of our campers stock stabilizers. They bolted right up to the brackets and glad we have new stabilizers. I hope the paint lasts on these as that seems to be an issue with the other, cheaper stabilizers. Time will tell.

Perfect! My weld for rear bumper was in the way of the bracket, so I just swapped 1 bracket each side from the old jacks, jacks were same size but rated lighter weight. Thanks for quick delivery! Always like the tutorials and pictures.

The box was a bit beat up when it arrived, but hopefully everything is intact.

This is what I needed. I Wanted a little more lbs. of lift so I could lift my truck for weight bars and such. I have a 2014 Rockwood A Fram and needed the mounting holes to line up. After some research, I found Stromberg jet-3755 worked perfectly. I have used it for a year now and no problems. Easy to set up and use. Thank you etrailer

Item arrived a day early. Installation was easy. Jack works smoothly. 3500# rating is 500# better than the factory installed jack.

etrailer did a great job. There was a problem with the shipping from UPS. etrailer sent me an email to see if I received my electric tongue jack. I hadn't got it. I responded and they looked into the missing jack and found out where it was and it was delivered. As for the jack it was an easy install and works great. Great customer service.

Easy installation, reasonable price, works great! Much to my surprise, our trailer had a 2.25" top hole and a 2" bottom hole. This jack fit fine. The lights are helpful.

Been a year and they work as they are designed. Much better quality than the ones that came on my camper. Easy to install. Going to replace the others over time.

These stabilizers are much better built that the ones that came on the trailer. The lift components are sturdy and the screw shaft is bigger diameter.

I mounted this Stabilizers Jacks to the back of a 4x8 utility trailer. I use the trailer to haul my Honda ATV to MotoAmerica motorcycle races. Once the ATV is removed I lower the jacks and mount my tent inside the trailer. These stabilizers allow me to safely move around in the tent without fear of the trailer tipping.

Does not ratchet up, a pin must be manually inserted. It only came with one 6" long pin, which needs to be cut in half to make these stands functional. This is more like a folding jack stand, but the pin is not connected to the stand with a lanyard. I will be cutting the bar in half and welding a washer to hold it in place. I will also need to add a lanyard to it so I don't loose it. I would not recommend this product, but I have not found a better substitute for my application.

Got my product when promises. exactly what I ordered ( and on sale too) Alex was great. I WILL BUY HERE AGAIN

Finally got around to installing my PT II Stabilizers 30" front and rear of our 26' Surveyor. Pre - assembled them to make sure they went together ok. Luckily I had two sources for power front & rear which made wiring easy, I used a Buss block to make all positive connections, grounds straight to frame, soldered all connections and heat srinked to seal. Using the 3/8" self tappers was fun.Well got it all together and all works well makes trailer very stable, don't have to worry about scissor jacks collapsing anymore.

The product works as designed. Easy to install and I have used it approximately 20 times in the last year. The storage for the 7 pin connector and safety chains are a great option. Keeps things nice and tidy when unhooked. I highly recommend this Jack.

Perfect fit and operates very quietly and with abundant power for my 27 foot Lance travel trailer. The Jack-It Lippert bike rack mount fits perfectly over it, and the manual emergency jack crank fits within the tube of the Jack-it if the need arises. Also, the handy ring for stowing the trailer chains and receptacle for stowing the 7-way connector is a nice feature. Very happy with my purchase, and etrailer is fantastic, as usual!

The bull dog electric tongue jack is awesome. I got it in white to match my trailer. I unbolted the old jack and bolted on the new one in about 5 minutes. (I had my coreless impact gun.) Total install time was about an hour mainly because I wired the jack to my battery inside the trailer that runs the electronic winch and I had to run a separate ground from the battery to one of the mounting bolts for the jack with a cut off switch. So far it works great but time will tell. I'll be using it a lot more next year.

Easy installation, works well for my 7000# trailer. The LED light is a nice touch. Rasies it easily. Super helpful customer service and fast shipping as always. What more could I want? Thanks Kathryn & etrailer!