# 1
Saris Bones 3 Bike Rack - Trunk Mount - Adjustable Arms
WOW... Outstanding product, well-engineered, quality materials, easy to install, works as advertised, and a perfect fit to my 2016 KIA Forte5. Not cheap... but, you get what you pay for... can't imagine a better bike rack out there. Great bike rack!
Faster and cheaper than other online retailers
# 2
Kuat NV 2.0 Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Gunmetal Gray
This thing is built like a tank! It is of the best fit and funtion I have seen in a bike rack! Solid as can be, fits my bikes perfectly and looks awesome! Plus it folds completely out of the way to access the rear liftgate on my 2022 Rav4!
Great service from etrailer and the rack arrived as expected. Fairly easy assembly. OK video on Kuat’s site, but didn’t cover the foot pedal. Really glad we got the 2” hitch. It tightened up and we’re impressed with the quality and the stability of the rack. We haven’t done a road test yet, but look forward to putting it to the test. We have a Ford F-150 and it works great. The bikes were fairly easy to load with the batteries out and two people. We do need the strap extenders for our RadMini Step Thru’s. The tires are too big for the ones that come with. Only one set of extenders came with the bike and one adapter for a smaller tire. It’s okay, but since it’s a two bike unit, would have been nice to have both extenders. Otherwise, we are really liking the look and stability.
# 3
Thule Hitching Post Pro Bike Rack for 4 Bikes - 1-1/4" and 2" Hitches
This is a solid, easy to use rack with one exception: rather than using a smooth bolt and cotter pin to secure the base of the rack to the trailer hitch sleeve, this rack uses a threaded bolt that has to be screwed through the sleeve and the rack. This might not be a problem with many vehicles but I have a 2003 Audi Allroad with so little clearance around the hitch sleeve that it's a real hassle both to screw in the bolt and unscrew it.
The good: I like the way the bikes are held in and the ability to add the upright adapters to the bike frame holders. The straps are quality too. For a jeep with a spare tire, this is the perfect length to clear it. This rack is 5 stars from the bike holders to the base of it. The bad: the 2"receiver adapter and bolt are insufficient. I wish they made this in a solid 2" hitch. The entire setup is held into the receiver by a very short bolt. It only goes about half way into the receiver tube. So your hitch is only "secured" on one side. A hitch pin or bolt should go through the receiver tube completely imo so it can be secured on the other end with a retaining clip or nut. Because this only goes in the one side, the entire weight of the rack plus bikes are held tight to one side of the receiver by the undersized bolt and washer. A few bumps down the road and that bolt loosens. Now instead of distibuting the weight of the rack and bikes on the receiver and post, it's completely up to the bolt to keep you from losing the rack. The bolt threads get damaged too. I took this down a dirt road and nearly lost everything. I had to buy my own bolt with hd fender washers and lock washers to correct this. Thule should've provided this from the start. The current short bolt design where only one side of the receiver secures the rack is unacceptable. This rack is 1 star at best for the connection to the receiver.
# 4
Yakima FrontLoader Wheel Mount Bike Carrier - Roof Mount
Overall I am happy with these bike carriers. They mount to the racks over the bed of my Tundra TRD Pro. Installation is simple. I think they could be just a bit sturdier because there is just a bit of wobbling when driving on bumpy roads but I'm not too worried about them coming dislodged. Take note that although they come with a cable lock to attach the bike to the carrier, the key is sold separately.
Very good product. It holds the bike securely on the roof without contacting the frame. It is easy to adjust from my road bike to my 29er mountain bike. Our drives are all relatively short, so I like that I do not need to remove the front wheel to lock in the bike. It's also nice that the SKS locking system allows me to use the same key for this rack that I use for my Yakima roof box and hitch rack. This is my first roof rack and I chose this route for a couple reasons. Some of the roads we travel to get to our trail heads are a bit rough and with a roof rack I don't have to worry about bottoming out a hitch rack hanging off the back of the vehicle. Also, it takes up less room in the garage. Our vehicle is a 2000 Jeep Grand Cherokee with an additional 4 inches of ground clearance. That makes it a bit of a reach for my 5'4" wife, so we take our two-step along to help her. This is my third time purchasing from etrailer, and each experience has been very good. They are a very customer service oriented company. I really appreciate all the additional information they provide on their products, especially all the videos they produce to aid in reviews, assembly, and use.
# 5
Swagman Chinook Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
Truly grooving on my wife's new Swagman Chinook bike rack. She wanted to be able to transport her nice road bike easily without throwing it in the back of her car, and since a roof rack is out of the question, this Swagman model fit the bill perfectly. It arrived quickly on the anticipated date. Kudos to etrailer.com for the email updates to keep me informed of my purchase. Within one hour, it was installed on my wife's 2014 Mazda3 hatchback. The Swagman is heavy and solid, which is reassuring as it makes me feel confident that it will keep the bikes secure. It also makes me feel like I got my money's worth. A ratchet wrench and Phillip's head screwdriver were the only tools required for the easy install. I did my research before purchasing the Chinook model as I was also eyeballing a very similar Thule rack that was slightly more expensive. I spoke with an etrailer.com expert who gave me the lowdown on both models. Ultimately, the Swagman won out because it has a smaller 'footprint' while extended or folded up ... and also can tilt away from the car for easy access to the hatchback area. Very convenient! FYI: Mazda doesn't make a trailer hitch for the Mazda3 as it's a small car with a small engine and has no business towing anything. Thankfully, the Curt company makes an aftermarket frame and trailer hitch that fits the Mazda3 hatchback perfectly with no drilling. Stupidly, I purchased it from another online company thinking I was getting a good deal. Turns out etrailer.com had it for less with FREE shipping. Oh well ... live and learn. Now I know that etrailer.com is one-stop shopping for bike racks AND trailer hitches. (Full disclosure: I had the garage down the street install the frame as it's easier with a lift) Only snafu: the shipment contained an extra set of keys that I assumed was for the hitch bolt lock (there was also a set of keys on the bolt itself). I spent 15 minutes using those keys trying to figure out how to remove the lock from the bolt to install it on the hitch. The keys just wouldn't turn in the lock. I called etrailer.com and Kevin told me to try the other set of keys ... and they worked. So an extra set of keys came with it that did absolutely nothing ... weird! Obviously, I can't speak to the longevity and durability of the Swagman Chinook 2 Bike Platform Rack as I just installed it. What I can speak to is the sturdiness of it, the ease of the installation and my complete satisfaction with the good folks at etrailer.com.
I ordered the Swagman Chinook 2 Bike Platform Rack on line from etrailer and so far have been very satisfied. The bike rack was delivered in less than a week. Unpacking the rack and assembly was fairly straightforward. I have read some reviews that complained the assembly instructions were a bit vague. I didn't have a problem but can see where others without a mechanical background get confused. The rack is very sturdy, but there is some side to side play in the tilt mechanism. I'm not sure this can be avoided with a rack that folds down. Installing the Curt trunk stabilizing strap takes most of the sway out of the rack. Installation is fairly easy and quick. It takes me 6 - 7 minutes to install the back on my hitch, and to install the bike and be ready to drive away. That seems reasonable to me. So far I've only loaded 1 bike. I've included pictures of my installation on a 2014 Mercedes Benz E350 sedan. Clearance between the bikes, the rack and the car are good. With the bike loaded in the inside, most forward position, I have 6" clearance between the pedal and the bumper. With the bike removed, the center support folded flat and the rack folded up in the storage position, I have 4" clearance between the closest part of the bike rack (the fold down hinge assembly) and the back bumper of the car. I am able to open the trunk of the car without removing the bikes or using the tilt feature, but I do have to remove the stabilizing strap first. Overall, I'm very pleased with the bike rack and think it will serve me much better than my old strap on rack. Since the weather has been cool since getting the bike carrier, I haven't taken any long trips to give it a real workout.
# 6
Kuat NV 2.0 Base Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Matte Black
I've taken this rack all over New England on the front of my Dodge Ram 3500 pick up truck with a truck camper. I had no idea it was possible to love a bike rack so much. After one drive I didn't ever worry about it again. So nice that it locks up when I am camping or taking a quick stop for food on the road. So glad I bought it from etrailer. They totally help me pick the perfect rack for my challenging set up.
Still very new, but what an awesome bike rack! Assembly was a snap and the rack is rock-solid when you secure it to the hitch receiver. etrailer was amazing too - excellent communication, price and fast, free delivery. Overall I am extremely happy with the rack and service!
# 7
Thule DoubleTrack Pro XT Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
I purchased the Thule DoubleTrack Pro XT Bike Rack from etrailer because of their customer service and fast shipping. The Rack was actually on sale on etrailer, Thule, REI and other retailers, but my choice was etrailer and like always etrailer does it correctly. Rack was on time and no parts were damaged. Only thing missing was the plastic straps, as soon as I realized they were missing I called etrailer and spoke with Roger ( great customer service based on the USA, no calls to foreign call centers) on a Sunday, 3 days later I got my straps and my whole bike rack was completed. I have been using it for the past 2 weeks and everything seems right and fully functional. Thanks etrailer !
Disappointed in the quality control from Thule. One of the nuts provided had no threads so had to hunt down a replacement at the hardware store. Also one of the wheel tray ratchet mechanisms doesn't spring back like it's supposed to. For the money Thule wants for its products you'd think the quality would be better.
# 8
Kuat Sherpa 2.0 Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Gray
So after much research into bike racks, I decided on pulling the plug on the Kuat Sherpa 2.0. I've looked into the Kuat NV and other brands, but they were just too much for my needs. If you've got "regular" bikes and not the heavier eBikes, then this rack is perfect. I wanted a hitch rack that was user friendly and not overly complicated. I have a mixed bag of bikes and this rack can handle them all, from mountain bikes, street bikes, and BMX bikes. I like that this rack comes with an adapter piece for 20"-24" wheels. Assembly of the Kuat Sherpa 2.0 is really a no-brainer. I think it's only 4-5 bolts really. Everything else is ready to go. The anti-rattle hitch ball mechanism is simple to use with just a twist of the dial, easy. The tilt pedal/lever is also easy to access should you need to open your hatch, a solid "click" assures it's in place. So far, loving this rack. Fit and finish is superb. Thanks to Jerred and etrailer for answering my questions, always helpful.
OMG!! I have been researching and pricing bike racks for a month. Every time I thought I was ready to pull the trigger, I have a question or review that through me off the trail. I was ready to purchase the rack from outdoor retail store and drive 2 hours to pick it up from store to save the $75 shipping, when I thought about etrailer that I had used when I had a travel trailer. Checked them out, they had the exact rack I decided to buy, with $[XX] discount and free shipping. Life doesn’t get any better. It was delivered right on time and in great shape. BTW etrailers website description and videos were better than the racks manufacturer site. You are Rock Stars in my book. Overall, start to finish was above and beyond expectations.
# 9
Yakima OnRamp Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
This is a great product and works beautifully! The only issue was some sloppily made plastic turn knobs that were cross threaded on arrival. However, Yakima immediately shipped out replacements. It carries two large E bikes easily. They fasten solidly and are easy to load and unload!
etrailer: prompt delivery, fair price! Rack: It does fit my (2) Gazelle T10 eBikes. 1) I found I had to adjust every setting to get bikes to fit. Until you learn there are many adjustments, it does not seem like the center/vertical clamps will reach both seat posts. 2) The ramp is barely usable; my wheels are max it will fit and you must have at least 12ft of clearance on each side of car to get bike lined up with ramp. 3) My bikes have a "walk" feature, this is not usable as its too awkward to hold the walk button down and move around the rack. I found its easier to abandon the ramp and load front then rear wheel. I will rig up a wheel stop, on ends of each wheel holder so bike will not roll off while I strap it in. 4) Rack did NOT come with a lock for hitch pin; this is very disappointing as they say in manual this is an optional item. Every rack I have seen at least has a clip that would otherwise hold the hitch pin in if somehow the bolt loosened up. 5) The rack weight is the lightest I have found. 6) You must load the first bike (closest to car) from car passenger side. This will avoid you bike pedals hitting the vertical bar. That means you must load the 2nd bike manually as there is no way to get the pedals past the vertical bar. I will get used to this, I hope. 7) The rack is a few inches above the receiver (part that goes into hitch) so if you have a low hitch this might be an issue with ground clearance. With both bikes mounted up, it seems very stable and hopefully will be secure in travel.
# 10
Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
This bike rack works great for our 2 Lectric 2.0 e-bikes. We mount it on our 2019 Honda Ridgeline. It folds up nicely when it’s on the truck and we are using our bikes. The locking mechanisms work well also. I contacted support for a smaller hook arm to clamp B over the bike frame. They knew exactly what I needed and shipped it - no problem.
I've been using this bike rack alongside a trailer hitch I got here for my small car (chevy bolt ev) and it was exactly what I was looking to get to haul around my fat tire mountain bike bike. Sometimes I throw two bikes on there (either an e-bike, slightly heavier at 60 lbs, or a 2nd mountain bike) and it's perfect.
# 11
Inno Tire Hold Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Tilting
Loved it so much we ordered it twice! We had our first rack 3 years and re-ordered after we were rear ended and the rack was damaged. Our e-bikes go on and off easily- assembly was easy. We have a 2020 Toyota Highlander and this rack works beautifully - in the photo I have blacked out our license plate state and number. I put reflective stickers on the rack tire holder bar, as our back license plate is maybe difficult to see with the bikes in place. We wouldn’t need to, but we also remove our bike batteries to lighten the load and reduce road and weather spray during our 1,900 mile trips. We LOVE that the bikes tip away so we can access the tailgate without removing the bikes!! Best bike rack ever.
Overall excellent quality, easy to use and install. We’ve used this regularly for the past year with ease! 4 stars because we’d prefer that it had a standard 2 inch hitch instead of the 1 1/4 inch with adapter. This would remove the little wobble factor which bugs my husband. I had to remove my cute rear bike fender because of the way the tire clamp arm attaches to the tire. If that could attach at a lower point on the tire I would be stoked!
# 12
RockyMounts MonoRail Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
At age 75, I have purchased many bike racks over the years…..this one has no equal in loading and unloading…
This rack is really, good. The only thing i add to make it better is small strap that holds the front wheel to the front wheel bracket. I never had a problem with it, but i like to make sure it is secure. It is a solid bike rack and worth every penny. I would buy this over the Kuat version any day.
# 13
Hollywood Racks Destination Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
The Destination bike rack works perfectly on my 2020 Pacifica and I have clearance going over speed bumps! I recently upgraded my bike to a Trek step through which hung too low on my old Thule rack no matter how the cross bar adapter was adjusted. Problem solved!
I realy like how it holds my bikes securly in place. I also like that (without the bikes) I can open and close the hatch on my 2014 Hyundia Santa Fe. I have a 2" receiver on my car. We went away for a long weekend from CT to VT and had no issues with it holding my bikes. Would definetly recomend.
# 14
Yakima HighRoad Roof Bike Rack - Wheel Mount - Clamp On
1. One star ding for price. Fairly expensive for a single bike, especially after adding a lock core. 2. The rack works exceptionally well and I'm not disappointed with the purchase. Installation is fairly simple. It does take a bit of fiddling to get the tension down on the rack clamps (connecting it to car) but it is a simple affair, and I'm able to move it between an aero rack and a round rack with out adjusting the tension. The sliding tray in the rear is a bit sticky, so if you carry bikes of different wheelbases, you may need to add some lubrication to the tract. Front wheel locks into place (I've used 700x25 and 29x2.3) simply, and the clutch in the tension wheel is a nice addition. It would be nice if there was a quick release button (like in times past) but it spins fairly quickly to unload. The locking whip is a nice addition. I have been able to rout it over the chainstay on both bikes. However, it is too short to route around chainstay and wheel. I'd prefer to include my rear wheel inside the lock. Overall, I'm very happy with the product.
I bought two of these, they work great, good the bikes very solid and I'm confident using them over hundreds of miles. etrailer.com is my go-to for tracks and accessories
# 15
Thule UpRide Roof Bike Rack - Wheel Mount - Clamp On or Channel Mount - Aluminum
Very easy to use (once you do it a couple of times). I have ebikes and they handled the weight (48lbs each). The biggest issue I have with this racking system is wishing there was a left and right models of it...unless I didn't see one when ordering.
Basically, bolt it to your rack and you're ready to go. Easy to use once you do it a few times. My only complaint is for $200 they could throw in a lock core. Also, this etrailer response is incorrect, it is actually pretty simple to swap the operation of the rack to work on the driver's side (without having your bike face the wrong direction). Two plastic locks hold the main assembly together, unlock, take the hook out and put in the other way. The loop thing at the front is held in by one allen bolt on the bottom; take it out, swap the direction. Finally, the rear tire strap slides out the back; reverse it and slide it on. It takes longer to put the carrier on /off your rack than to swap the direction (not more than 10 minutes).
# 16
Rhino-Rack Bike Rack for 2 Bikes - 2" Hitches - Tilting
I purchased this bike rack a year ago and I use it A LOT. I had to buy and install a stabilizer because without it, the unit would sway back and forth even without a bike on it (very noisy). This makes removal more cumbersome but since I keep the hitch on year round it doesn't matter to me. The tilting function is fabulous allowing easy use of my RAV4 hatchback. I can even tilt it down with a bike on it. I got the 2 bike hitch. Plenty of room for two bikes to fit without rubbing. Lastly, the hitch has a sizable through-hole on the bottom to thread a good sized cable so I can lock my bike up. Sturdy. I highly recommend.
The unit ‘s simplicity is a real plus. It takes less than 3 minutes to put the rack on the vehicle. It is well built and very durable and has a nice feature that allows you to open the rear hatch for SUV owners without removing the rack.
# 17
Kuat NV 2.0 Bike Rack for 2 Bikes - 1-1/4" Hitches - Wheel Mount - Gunmetal Gray
Love the fit and solid quality build of this bike carrier. Can't wait to try it out. I am using this carrier for two e-bikes and I am confident that it will hold up very nicely and will have no problem holding the weight of the 2 bikes.
Great product! I needed something to transport my e-bikes which tend to be on the heavy side. this product does not disappoint! Great staff at this store. They were very helpful and guided me I'm making the right decision
# 18
Hollywood Racks Trail Rider Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
I was impressed with this bike rack from the minute I unpacked it. The assembly was simple & straight forward. I looked at quite a few bike racks & for the price point this product was hard to beat. It is well designed & the keyhole pins make it easy to remove & fold up when not carrying the bikes. The locking hitch pin & locking frame bars are convenient and fairly secure. I will add my cable lock to make the bikes even a little more tamper proof. So far I’m very happy with this his purchase. Now the test of time!
I looked at a LOT of bike racks, but when I saw the product video for this Hollywood rack and it was holding the bikes rock solid, no loose bouncing anywhere, I decided to try it and I haven't been disappointed yet. It is solid in the mount, it holds the bikes securely and the locking bars are a good deterrent to anyone wanting a quick steal. I don't leave mine on the car all the time, but so far in the weather here in Florida, it's holding up nicely. Add all this to the great price and customer service from etrailer.com and it's a big win for the average consumer. Thanks, etrailer!
# 19
Curt 2 Bike Platform Rack - 1-1/4" and 2" Hitches - Frame Mount - Tilting
I installed this rack onto a Curt trailer hitch which is mounted onto a 2017 Honda Fit. I have been using it intermittently for several months, probably about 5 times with one bike and twice with two bikes. I give some pros and cons below and then elaborate. Pros: easy to assemble, easy to mount and dismount bikes, easy to lock and unlock, how to put the rack into different positions is intuitive Cons: inconvenient to put the rack into different positions, inconvenient to mount the rack onto the hitch, rack protrudes about 15 inches from bumper when in flipped up position (seems very vulnerable to someone backing into it in a parking lot, very inelegant looking I say the repositioning is intuitive because there is really only one way you could possibly place the pins for each position. But removing and replacing two pins is much less convenient than turning a knob or a lever, like some racks do. Also many racks fold and flip in such a way as to look very unobtrusive when in non-use mode. This one looks like kind of a monstrosity. That does not really bother me but it might bother some owners. The part that does bother me is how far it protrudes from the car. I back into parking spaces whenever possible to avoid someone bumping into the rack and damaging it (which happened to a friend). My number one suggestion for Curt is related to mounting the rack onto the hitch. Make it easier to tell when the holes are lined up so that the bolt/pin will fit and thread. As it is now, if you insert the rack as far as it can go it is way too far in. Ideally, it would be exactly lined up. Failing that, maybe some kind of click or other feedback to know at least that you are in the neighborhood. It would also be great to have an attaching device that is easier to fasten and unfasten than is the bolt/pin. Tip for mounting the rack onto the hitch: I assumed that it would be awkward to hold, what is it 46 pounds?, while trying to line up the rack probe with the receiver. If you have a garage with exposed collar ties, my solution could work well for you. I looped a cargo strap over a collar tie. Then I hooked both hooks of a bungie onto that loop. The idea is that you hook one of the bike frame holders of the rack onto the bungie, suspending the rack a few inches off the garage floor. This takes most of the weight of the rack so that you can just pull up or down and forward until you line up with the receiver. Tip for mounting bikes. Don't put the little screw into the post that prevents you from completely removing the bike frame holders. Remove both holders. Position the first bike, slide the holder into place, position the second bike, slide the holder into place. I found this makes it much easier, because you avoid parts of the bike hitting the holder as you are trying to get the wheels into place. The trick is that if you are mounting only one bike, don't forget to put the second holder back on - or maybe just stick it inside the car right away.
I had a 1 1/4" hitch installed on my 2016 toyota camry (the only size offered on the camry). I was very pleased with the ride. I expected to hear alot of noise like experienced when towing a trailer, but I heard almost nothing accept when going over speed bumps. I had to extend the tire supports to their widest position because having mountain bikes with a step through angled bar, they were more secure the closer i could get the upper and lower support arms to the seat post. The bikes were mounted in opposite directions and only stuck out maybe 6 inches or so. One locking barrel on the lower support arm was malfunctioning and gave me trouble but i called etrailer and they sent a replacement as soon as they were in stock. It comes with a anti rattle hitch pin but I highly recommend purchasing an anti rattle hitch pin with a lock on the end instead of just a clip for more security when unattended. After a few times mounting the bikes and figuring out the best way they should be positioned (pedals positions, direction of bike, and that my wife's smaller bike fit better going on first with my larger bike on the outside) I can mount the rack and bikes and be ready to go in just 5 minutes. (70 pounds on a torque wrench recommended for the hitch pin) I am overall pleased with my purchase i would recommend this product.
# 20
RockyMounts BackStage Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
We love our RockyMounts BackStage Bike Rack. The fact that it can hold our two e-bikes and swings out for rear door access makes it perfect for vanlife. Service and communication from etrailer is outstanading!
etrailer.com asked me for a review about 1 week after it arrived. A better review would be in about 6-12 months after delivery to allow me time to use and experience the rack. Disclosure: my review is just for the assembly and install. Assembly is not easy. I needed to go to the internet and look at photos. The instructions lack detail. So only 4 stars for assembly instructions. It seems like a good design. The included locks seem cheap - like why bother including. The hitch pin design seems to tighten down the rack so there should be minimal rattle and movement. The rack sits up relatively high, so it would be safer to lift heavier e-bikes with two people or use some type of field engineered ramp. Wish it was made in the US and I wish the country of original was fully disclosed in the etrailer.com description. Perhaps it is disclosed but I learned it was from china after it was delivered.
What our customers are saying:
"Just to let you know I was very satisfied with my orders for a hitch, wiring harness, bike rack and extension. I have a 1995 Dodge Ram van and some of the parts are hard to get elsewhere. I received all my orders proptly and will recommend you to others. The pricing can't be beat. Thank you. Sincerely, Frank"