Best 2012 Hyundai Santa Fe Trailer Hitch Ball Mounts

2nd order from etrailer, great customer service & fast delivery! My 2" ball fit the ball mount perfectly and I installed it in a few minutes. Make sure that you use a ball with a 1" shank. It stores easily underneath my Hyundai Santa Fe cargo mat until I need it.

My order arrived in two days. I am impressed both by the layout and functionality of etrailer website and by the quick, free shipment. The hitch for my 20007 Hyundai Santa Fe is well made, well finished and fit perfectly. The estimated installation time of 30 minutes would probably have been accurate had I not had to clean 3 years worth of rust from the mounting nuts installed by the factory. Once clean (no simple task since reaching them with a 10m/1.25 tap was difficult) mounting the tow bar was simple and made easier with a pair of jackstands. Owing to the design and location of the mounts, reaching them required the use of different ratchet extensions and flexible joints and I'm not certain of the accuracy of any torque reading. In summary, I am pleased with the product and impressed by the follow-up from etrailer. I will recommend them without hesitation.

Sturdy ball hitch and easy to install.

This is a great, cost effective set. I love it so much!

Arrived right on time in excellent condition. All instructions were straight fwd. Could not have been any more detailed. Excellent product and outstanding service, my compliments. Fit our 2017 vehicle without a "hitch"! Ordered hitch and ball with this, but was not aware that the pin for the hitch was not included, my fault for not checking. Thanks for the excellent product and service. Jack R.

Quality product.

To be honest, I use it upside down. I needed a hitch with rise, but none were available at time of purchase, and yours, inverted, works perfectly! The welds are regularly checked and remain all secure. It's a good hitch.

Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.

Great starter kit..the only thing missing from the package was the receiver cover..thus the 4 star rating.

Directions was good, easy to install. Very happy.

Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .

Perfect fit for 2 inch Draw Tite receiver. good price, fast shipping.

etrailer has what you need

I would give five stars but due to what looks like packaging problems the hitch came very marred and the coating chipping off.

I purchased this Curt Ball mount 10-1/4" because I also bought ball hitch mounted mud flaps and my existing hitch was too short.This hitch was maybe a little too long, but it should work.I hope this combination will protect my horse trailer from my nasty gravel roads!

With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.

We sold our small motor home and purchased a small travel trailer. This hitch provided a perfect solution to how to use our bike rack while towing the trailer. It even allows room for the pickup tailgate to be lowered without removing the bikes from the rack. The hitch is very hefty with a high weight limit - plenty for the GVW of the trailer (7,000#) plus 125# of rack and bikes.

This has been an amazing multipurpose ball mount. We purchased this to use with our Hollywood Bike Rack and also to connect onto our boat. We weren't sure if this would work, but it was awesome. It is very well built and We had to make some minor adjustments to the position of our boat on the trailer so the turning radius of the bike rack that was attached would clear the truck. This is very well made and solid.

Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.

This item should solve the problem I have had with a stainless 3-way ball when I tried to reverse the position on the ball mount. The threads galled between the hex nut and hitch ball.

Fits our VW Touareg perfectly and allows us to tow a variety of things now. As can be seen in the pictures the hitch has a +5-inch gap between the bumper and the vertical adjustment pillar and the trailer itself is out further so there's enough room to get to the rear hatch and maneuver the vehicle/trailer.

I needed a hitch that I could haul my work trailer with and still drop the tailgate without dropping the trailer. I looked on etrailer and found one that would work barely but decided to call etrailer and see if anyone had any ideas. Steve answered and looked after I told him my requirements and came up with this. This has a longer distance from ball to pin by a few inches compared to the one I found so my tailgate will still drop even if I’m at an angle to my trailer or on a hill. Also with the adjustable height it’s great. Awesome hitch. Solid for a good price. ??

Haven't been able to break it yet.

I hooked up the draw bar today for the first time to the trailer that I built and the hitch I installed. The draw bar uses a cotter pin that slides on the bolt rather than going through a hole to mount the bar to the hitch. I have never used a sliding on pin in anything - I've only used those that go through a small hole matching the pin. This includes my farm tractor and other tools. I hope it is secure because it does slide on easily. The bar itself appears nice and strong.

Overly tight on the receiver end bit functions as intended.

I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.

The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.

Works great solid product.

Retail type stores only carry mainstream items so when I needed a special length ball mount for my 2011 Traverse I found the size and quality with Curt Products .

Recently bought a Kubota RTV x900. The receiver is located under the bed. With the extra long ball hitch drawbar I can easily get to the drawbar and use a clevis to hitch my 5ft. wide mower or attach a ball and use the trailer. The pictures will illustrate the length of the drawbar which makes access very easy. The product is heavy duty and well made. Ordered this product on Thursday morning and it was delivered the next day, Friday afternoon. Customer service was helpful, will use etrailer again. Thanks

Love these. This is my third one. Wouldnt pull a trailer with anything else. Trannys are expensive.

As a full-time RVer, e-shopping is very important for us. etrailer was the right place to shop. Right product, delivered on-time for a great price. You beat the local discount RV store by $25 including shipping. At the same time, I had another outfit send me a clearly inferior product to the one they displayed. Said they would e-mail a pre-paid shipping label for the return (didn't) and tried to put the blame on Amazon. Thanks etrailer for a great experience !

We bought this to tow our 3,000 lbs. boat with our Subaru Ascent with a 5,000 lbs. towing capacity. With the OEM ball mount, we could really feel every jolt and jiggle from hard stops, going over bumps in the road, and trailering down dirt roads. However, the dual cushion ball has really improved our trailing experience. Once we get up to speed, we hardly notice we are towing our boat. It's also great because some of the lakes we visit are down dirt roads, and the cushion makes this a much more pleasant experience. I would highly recommend this to anyone towing a boat or larger trailer with a SUV as it maintains that comfortable ride and the jostling of the trailer is much less noticeable.

A year has passed with my Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount and I have nothing but praise for this mount. Once you find the correct height to have a perfectly level trailer there's no need to adjust. The beauty lies in the cushioning! Towing a Yamaha AR190 (3200lb boat and trailer combo) is silent. Even over the bumpiest pavement the tow is smooth. There is no harsh slamming when braking or taking off from the boat ramp. I don't know why everyone isn't running one of these, I wouldn't run any other hitch mount PERIOD! If you're on the fence, get off and buy one, you will NOT regret it!

Very happy with this ball mount - provides just the amount of drop we required for a level tow of our GeoPro travel trailer by our RAM2500. Plus, the extra length not only allows a tighter turning radius, but also allows us to lower the truck tailgate without having to detach the trailer. Huge improvement on all accounts for us compared to our prior setup. The product is well built and I'm confident will provide us years of good use.

Great customer service. Live in SC - ordered a hitch and USPS delivered it to PUERTO RICO. Go figure. Stacey A refunded my money - but 2 weeks later hitch appeared on my doorstep. All’s well that ends well.

works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.

This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.

This is really nice. Beveled edges so it slips into receiver hitch so sweet. Beautiful welds heavy weight mount for my weigh safe ball. I bought a 10,000 lbs hitch and I wanted a draw bar with the same type rating. Now the only thing limiting my trailer capacity is my truck's ability to tow, not the hitch, bar or ball.

I purchased a Ranch Hand rear bumper for my 2500HD but wanted to retain the use of a receiver hitch. The ball mount would need to extend 8" from the pin hole to even reach the edge of the bumper. This BM29 ball mount works out perfect. The welds look great and the finish is just fine. The only complaint I have is they gained a little length by moving the pin hole a little closer to the end shortening the insertion amount slightly. Not a big deal, it is just noticable next to the other mounts I have at the house.