# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Fastest delivery I have ever had. Ordered Wednesday at 5PM, arrived Thursday at 3PM. I'm only a couple hundred miles from Wentzville, but still, excellent. The hitch receiver (2008 Pilot) installed quickly and easily. No need to remove spare or lower muffler. I supported the left end on a large cooler and quickly maneuvered the right side above the tail pipes. The mounting holes were right on target. I had to tap mine to remove rust, but that's easy as well. The wiring harness was also a snapto install. Simple to plug into existing fitting and the wiring box tucked away nicely beneath the trim as advertised. There are options about what to do with the wiring tail and trailer connector. I chose the method shown in the video...leave it rubber-banded in the storage well. Others have run it outside through available holes, but I did not want to leave it exposed to road grime. etrailer's videos were very detailed and shown on my specific vehicle for both the hitch and the wiring harness. Good values as well. If I were Draw-Tite (or Curt) I would include a complementary rubber plug with their logo...cheap advertising.
At 68 yrs old, just single-handedly installed the 50 pound Curt hitch receiver on my 2016 Honda Pilot, using two jack stands and the vehicle's car-jack to position it correctly and hand thread the 6 bolts. Made a bit more room for myself by first lifting the back of the vehicle onto a makeshift ramp consisting of two layered 2x6 board. Also first tried to hand tighten the bolts before placing the hitch under the car and found I had a fair bit of rust to work through with rust blaster and wire brush. Instructions were clear and accurate. One tip, do the center bold on the muffler side first (to be able to slide the unit between the muffler and the frame, then the center bolt on the driver's side second. From there, it is a breeze. Took me an hour to get rid of the rust inside the welded bolts, and then an hour to install the hitch.
# 2
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
Exactly what the part says it is. Worked fine.
package arrived on time. the box arrived damaged scratches on paint but I still installed it. installation was easy thanks to you tube. the bracket for the wiring was short for my 2017 Honda pilot. bracket needs to be at least 3 inches longer I have attached some pictures other than that I would have been much happier it will do for now. I Hope this review help for the piloteers.
# 3
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
The item arrived on time and was exactly what I needed. E Trailer is a great place to fill all my towing needs.
Fastest delivery I have ever had. Ordered Wednesday at 5PM, arrived Thursday at 3PM. I'm only a couple hundred miles from Wentzville, but still, excellent. The hitch receiver (2008 Pilot) installed quickly and easily. No need to remove spare or lower muffler. I supported the left end on a large cooler and quickly maneuvered the right side above the tail pipes. The mounting holes were right on target. I had to tap mine to remove rust, but that's easy as well. The wiring harness was also a snapto install. Simple to plug into existing fitting and the wiring box tucked away nicely beneath the trim as advertised. There are options about what to do with the wiring tail and trailer connector. I chose the method shown in the video...leave it rubber-banded in the storage well. Others have run it outside through available holes, but I did not want to leave it exposed to road grime. etrailer's videos were very detailed and shown on my specific vehicle for both the hitch and the wiring harness. Good values as well. If I were Draw-Tite (or Curt) I would include a complementary rubber plug with their logo...cheap advertising.
# 4
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
Everything worked exactly as stated. Very easy to install. The videos are great. Shipping was fast. Very happy!!
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
# 5
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Great instructions, very timely delivery!
very high quality and fits perfectly.
# 6
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
Worked great. Was helping a friend move. Worked perfectly, easy to install and having both ball hitches, didn't have to worry about not having the right size for my friends trailer. Really made the move easier.
Thank you for the informative video instructions as well as helpful / honest reviews to research prior to making the purchase. I do not have anything to add that has not been covered in the reviews. Here is a recap of my experience that has been consistent with others. 1. Box was received with the driver side of the hitch pushed out. Only minor scratches which you can not see when installed and it did not impact the installation. Wrapping each end would probably be a good idea as stated in other reviews. 2. Removing 14 years of rust was the hardest part of the install (from the passenger side holes). Total time was approximately 1 hour as others have experienced. I used the bolts from the factory tie hook to work out the rust using 1/2" round wire brush attached to a cordless drill along with a full can of WD-40. 3. Installation of the hitch took about 30 minutes with assistance of a foot stool. 4. Plug-n-play electrical connector took about 10 minutes after watching the video. 5. Perfect fitment, fast delivery, easy website ordering experience and follow-up status notifications, and I can not be more pleased with the cost being under $200 for a DIY project. I required this setup to tow a ~1,000 lb motorcycle trailer with a ~1,000 lb motorcycle next week and my Honda has a 3,500 lb towing capacity. Thank you etrailer.com!
# 7
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I ordered and received the ball mount and sway bar together. They were received very promptly and in excellent shape. They are very heavy, i.e., heavy duty. The bracket that was fitted to the trailer was about half a screw wider than optimal size for my smallish trailer but did fit. Installation was easy. The self-tapping screws functioned well. All-in-all, a 10 out of 10 experience.
# 8
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
Exactly what the part says it is. Worked fine.
package arrived on time. the box arrived damaged scratches on paint but I still installed it. installation was easy thanks to you tube. the bracket for the wiring was short for my 2017 Honda pilot. bracket needs to be at least 3 inches longer I have attached some pictures other than that I would have been much happier it will do for now. I Hope this review help for the piloteers.
# 9
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
Exactly what the part says it is. Worked fine.
package arrived on time. the box arrived damaged scratches on paint but I still installed it. installation was easy thanks to you tube. the bracket for the wiring was short for my 2017 Honda pilot. bracket needs to be at least 3 inches longer I have attached some pictures other than that I would have been much happier it will do for now. I Hope this review help for the piloteers.
# 10
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
Exactly what the part says it is. Worked fine.
trailer hitch works great with no flaws in manufacturing welds. Purchased to drop cycle trailer down 4 " off my honda Pilot. Now trailer is level and goes down the road great.
# 11
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
Exactly what the part says it is. Worked fine.
package arrived on time. the box arrived damaged scratches on paint but I still installed it. installation was easy thanks to you tube. the bracket for the wiring was short for my 2017 Honda pilot. bracket needs to be at least 3 inches longer I have attached some pictures other than that I would have been much happier it will do for now. I Hope this review help for the piloteers.
# 12
MaxxTow Adjustable-Height Ball Mount - 2" Hitch - 7-1/2" Drop, 6-1/4" Rise - 5,000 lb
As advertised and quick delivery, I am an Etrailer fan!
Strong and works perfectly!
# 13
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 2" Rise, 4" Drop - 7.5K
Great products. Exactly what we need for our travel this weekend. Arrived quickly and just in time for our road trip! Thank you! A+++
Easy installation, low profile and excellent quality. Exactly what I was looking for in a hitch receiver for our 2021 Pilot.
# 14
Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount - 7" Rise to 9-1/2" Drop - 5,000 lbs
We bought this to tow our 3,000 lbs. boat with our Subaru Ascent with a 5,000 lbs. towing capacity. With the OEM ball mount, we could really feel every jolt and jiggle from hard stops, going over bumps in the road, and trailering down dirt roads. However, the dual cushion ball has really improved our trailing experience. Once we get up to speed, we hardly notice we are towing our boat. It's also great because some of the lakes we visit are down dirt roads, and the cushion makes this a much more pleasant experience. I would highly recommend this to anyone towing a boat or larger trailer with a SUV as it maintains that comfortable ride and the jostling of the trailer is much less noticeable.
Rusted within 30 days. The manufacturer refused to warranty the product. I have continued to use it, but it has required some serious rust mitigation and is a flawed product.
# 15
MaxxTow Ball Mount w/ 2" Accessory Receiver - 2" Hitches - 2-1/4" Drop - 5,000 lbs
Heavy duty , very good quality.
# 16
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This was the longest hitch ball mount I could find anywhere. I used it with a short extension for my 2021 T G so that I could open the back doors without hitting the trailer wheel crank. With my new trailer, Intact Flyer Discover, I don't need the extension and can still open the doors. Works well.
# 17
Curt Fusion Ball Mount for 2" Hitches - 2" Ball - 2-1/4" Drop - 7,500 lbs
Exactly as described. Well made.
Great deal on this, it was almost $20 more locally. Received it fast, it was packaged very well. This looks really clean on my vehicle and I never have to worry about "did I tighten the ball enough".
# 18
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
Exactly what the part says it is. Worked fine.
package arrived on time. the box arrived damaged scratches on paint but I still installed it. installation was easy thanks to you tube. the bracket for the wiring was short for my 2017 Honda pilot. bracket needs to be at least 3 inches longer I have attached some pictures other than that I would have been much happier it will do for now. I Hope this review help for the piloteers.
What our customers are saying:
"Easy place to shop. Fast delivery and great products. Very happy with my purchase."