# 1
Thule Hitching Post Pro Bike Rack for 4 Bikes - 1-1/4" and 2" Hitches
The good: I like the way the bikes are held in and the ability to add the upright adapters to the bike frame holders. The straps are quality too. For a jeep with a spare tire, this is the perfect length to clear it. This rack is 5 stars from the bike holders to the base of it. The bad: the 2"receiver adapter and bolt are insufficient. I wish they made this in a solid 2" hitch. The entire setup is held into the receiver by a very short bolt. It only goes about half way into the receiver tube. So your hitch is only "secured" on one side. A hitch pin or bolt should go through the receiver tube completely imo so it can be secured on the other end with a retaining clip or nut. Because this only goes in the one side, the entire weight of the rack plus bikes are held tight to one side of the receiver by the undersized bolt and washer. A few bumps down the road and that bolt loosens. Now instead of distibuting the weight of the rack and bikes on the receiver and post, it's completely up to the bolt to keep you from losing the rack. The bolt threads get damaged too. I took this down a dirt road and nearly lost everything. I had to buy my own bolt with hd fender washers and lock washers to correct this. Thule should've provided this from the start. The current short bolt design where only one side of the receiver secures the rack is unacceptable. This rack is 1 star at best for the connection to the receiver.
I bought this bike rack back in April but wanted to make sure I used it to give the best review. First I want to say I did a lot of research on bike racks and found this one to be the best one to fit my needs. The best price I found was on etrailer.com, at the time it was When I called the customer service to place my order, I spoke to Dan. He was very pleasant on the phone and took the time and listened to what I needed and understood my concerns. I ordered the bike rack and also ordered the Thule Snug Tite Hitch Lock and Anti-Rattle Device and the Thule Cable Lock w/ One Key System Lock. Dan suggested I also get the Thule Bike Adapter Bar, which I never even thought of getting. Delivery was in about two business days, which was really fast and at the time of order they were running a special free delivery over $99. When I went to put it together I noticed I was missing the flat cap screw M6 x 16mm, part number #853-5787-02. I emailed Dan and within 24 hours received an email that the part was sent out and also in the email their was a link to track the order. After I received the part I did notice that the flat cap screw was actually in the 2 inch adaptor sleeve. The instructions were very easy to read, and it took me about 20 minutes to put together. I did have an issue when I positioned the stinger into the cradle, with the 8mm locking nut, it was not staying tight and when I took it off I noticed the threads inside were gone, so I ended up going out to Lowes and buying a new one and its holds perfectly fine. I also had a question about that part because it is not a locking part and was worried someone would try to steal the rack. I contacted etrailer.com to find if they make a locking device for this and they said no but I can contact Thule to double check, I'm still waiting for an answer back from Thule. The weather finally broke and we installed the rack onto my hitch, tightened it and it doesn't rattle. When I finally used the rack and put my bike on, it did sway a little but at 50 mph I was very happy with it. The trailer comes out just enough away from my car that I do not have to fold completely out and I can open my trunk with no issues. I am very happy with my purchase and had a great customer experience with Dan. Would highly recommend ordering from them to anyone.
# 2
Thule Passage 3 Bike Carrier - Trunk Mount
I had a great experience! I ordered the bike rack Monday afternoon, it arrived the next day! I put it on the car that night. A 24-hr cycle of happiness! Pun intended! Thanks guys!
Fits perfectly on our Lexus CT200h. Only on the old LS400, the side straps have to be fastened to the wheel arch edge, since the upper trunklid gap is to narrow for inserting the strap hooks. Mounting of two bikes is (with some routine) quickly done, and they stay safe even for longer and faster routes. For transporting three (mountain) bikes, though, the design doesn't seem big and robust enough. Nevertheless, the price-benefit-fun ratios are way better than reasonable.
# 3
Swagman XTC2 Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
First-time rack buyer / owner / installer. The rack arrived in a timely fashion, maybe a day or 2 ahead of schedule. It was well packaged. I’m LOVING this bike rack. It was easy to put together and to mount on my new Honda Passport. Thus far, no squeaks in my 2” receiver. Hardest part of initial set-up is figuring out the best way to position two bikes. Trial & error and some patience. The directions weren’t clear as to where the 2 left-over screws went. I found the answer in another review and have posted a pic in case others have the same problem (photo with pen pointing at screw). These screws go in the underneath side of both of the folding arms. They appear to keep the wheel wells from sliding off in case in you drive with an empty, un-folded rack, and forgot to tighten down the wheel wells. The folding arm push / pull pins can be difficult at times. I coated the tips with some lube. That and a little jiggling seems to solve that issue. I guess it’s better for the pins to be snug vs popping right out. I added a small Master lock to the hitch pin (in lieu of the provided cotter pin) as a theft deterrent. I read that a 3/16 shackle lock will fit into the bike clamp down arms to also act as a deterrent. I had an old 3/16 lock that did snugly fit and appeared to be locked. HOWEVER, I yanked on the lock and it came open as there isn’t quite enough clearance for the shackle to lock. I discovered that longer 3/16 shackle locks are hard to find. Have attached a photo of the lock that actually fits and works (Ace Hardware). One lock on the upper clamp down arm will secure both arms as the lower arm can’t be removed without removing the upper arm. The clamp down arms appear to be coated to prevent damage to your bike. I’ve tried a simple rag and ultimately settled on pool noodle pieces as a precautionary measure. I CAN NOT open my tailgate (regardless of whether or not the rack is fold up and in the bike carry position). If that’s a concern for you, then spring for the more costly titling version. My back-up camera still functions.
The Swagman XTC-2 platform bike carrier arrived very quickly from etrailer and in good shape, the actual carrier box is inside another shipper box, which I'm sure helped with its condition. Assembly was relatively quick and painless, even though the instructions could be a little more thorough. Installing the carrier on the back of our Jeep Patriot also was quick, it helps to have an extra ratchet & 3/4" socket laying around for just this purpose. Installing the bikes takes a little patience and trial and error the first time you try and put them on the carrier. It's easy enough to adjust the wheel holders to fit the wheelbase of your bikes, but for us at least, the challenge was trying to swing the vertical support bar up into position after putting on the first bike (closest to the Jeep). We couldn't angle the bike enough toward the Jeep to have the bar clear the bike. We learned that the easiest way to secure the first bike was to remove the ratcheting frame hooks altogether, put the bike in the carrier, swing up the vertical support bar, put in the pin, and then slide one of the frame hooks down on the bar. The outside bike is much easier because you can set the bike in the carrier at whatever angle you need, not being limited by the back of the vehicle. One thing we did to protect the bike frames was to use some foam pipe insulation as cushion between the frame hook and the frame (see pictures). Once you get a system for installing the bikes, it is very quick to load/unload them. The rack seems to be well made and doesn't wiggle excessively when traveling. All in all a good product for a good price, would definitely recommend it for anyone looking for a platform bike carrier.
# 4
Swagman XTC4 Bike Rack for 4 Bikes - 2" Hitches - Frame Mount
If you've done any research or read any of the other comments on either this rack, or this seller...rest assured they really are as good as everyone says! I ordered my rack on around 4pm est on a Friday afternoon and within an hour I received an email that said they have shipped my product AND upgraded to priority shipping. Can't say enough positive things about the customer service! When the rack arrived, it took me a little over half an hour to get it set up. Probably would e been faster if I were even slightly mechanically inclined (or if didn't I didn't have to borrow a socket wrench from my neighbor). We finally had an opportunity to load up the bikes and head out for a ride today. As others have said, the first time you load up your bikes, it's kind of like a puzzle to get them situated. Took about 15 minutes. This rack is awesome! Very sturdy and the bikes were very secure. Only racks I have had in the past were rooftop fork mount racks. This is so much easier! On e we got to the trail (over an hour drive) getting the bikes off was a piece of cake. Afterwards, it was time to load them back up and it was less than 5 minutes to get them all on and ready to hit the road. There were other 4-bike racks on the website, but this one had enough great reviews that I felt comfortable making the purchase. After the fact, I'm very glad I did! I can't imagine the $800 rack can be that much better than this, and I highly recommend this for anyone looking for a 4-bike platform rack. I will definitely recommend this rack and etrailer.com to everyone I know.
Loads and unloads bikes super fast, and holds them firm. Wish I would have purchased this a long time ago instead of struggling with my old frame mount rack. I actually ride more because I don't dread having to load. Adjusts to different bikes easily. Time will tell if the fittings, springs, straps hold up to weather (I leave it on car). It is fairly large and heavier than the more expensive 4 bike racks (it's mostly steel vs. composite plastic), so if you are going to take it off hitch and store it - be prepared. Only recommendation I have is to add softer foam on the frame bar for traveling on rough roads.
# 5
Swagman Upright Bike Rack for 1 Bike - Roof Rack Crossbars - Frame Mount
Planning on bringing bikes while camping. I mounted 2 of the Swagman bike racks to my new Sportrack on my pop-up camper. The bikes fit perfectly. The racks seem sturdy enough. Not heavy duty, but for my needs they should be fine. Assembly was relatively fast and easy.
We have used the Swagman Roof Rack a number of times when we have needed the additional bike carrying capacity. It took a couple attempts to get the initial spacing of the bike rack properly balanced on the van’s roof rack as recommended by the instructions. But it was easy to do and once set was very easy and quick to put on and take off. The rack works great, the bike is easy to put into place and secure. The bike and rack are very stable and quiet and haven’t required any mid-trip adjustments. We always put the cheapest bike on the roof (lol) but do use a bit of duct tape to protect the finish just Incase. We are very satisfied with the rack and consider it quite a deal for the money.
# 6
Rhino-Rack MountainTrail Rooftop Bike Carrier - Fork Mount
Love this bike rack! It fits perfectly with my Rhino Rack Cross Bars. I'm very impressed by the lack of wind noise. With the bike mounted on the rack, you can barely hear the wind noise at 60mph. With the sunroof open you can hear wind noise, but as long as the window is closed, you can only slightly hear anything if the radio is off and you are trying to hear it. Amazing! Can't wait to get more use out of it in the future!
I have used a lot of bike racks and this is the one I keep on my 4Runner. It just works. It is the easiest to take on and off, which is important for me because between me, my wife and kids I have 4 bikes that need to be rearranged often. We also use a roof box, kayak racks and a SUP rack so I am always taking things off and on. The front straps loop over the bar and tightens with an allen key, the back is a couple wing nuts. Since there are 2 straps up front the rack is very stable when a bike is on it. I like that it comes with locks and the skewer is super easy to adjust, clamp and unclamp. If it is cold, dark and damp at 6am and I am tired, late for a ride and still waking up this is the rack I go for because it is easy. There are a couple things to be aware of though... You will need to put a drop of oil in the skewer every 6 months or so to keep it opening and closing smoothly. Otherwise is can stick. Sometimes if the skewer is turned just right there will be a bit of whistle because of a hole in the clamping mechanism. If I turn it to a different angle the whistle stops. And after going through the car wash with the rack on my roof a dozen times or so the black paint began to have a bit of a rainbow sheen. Not sure if it is the bike rack or the soap my car wash uses.
# 7
RockyMounts MonoRail Solo Bike Rack for 1 Bike - 1-1/4" and 2" Hitches - Wheel Mount
I just finished installing this rack on my 2017 Subaru Outback. I've been researching platform racks for about 2 months now, and the most important things to me (other than a reasonable price) were no frame contact, ease of getting the bike on and off the rack, not too heavy for me to take it off the car, and enough clearance in the back for me to close my garage door. This rack is perfect for me. And I like that it's expandable to two bikes if I want to do that down the line. It came very well packaged. I am a single gal and not handy AT ALL, but I was able to do the installation with no problem. I did put my bike on the rack and took a short test ride, it was very stable. Very solid well made product!
Feels solid, minimal wobbling. Easy to get bike on and off, and to access the trunk with the bike on. Like that it can be expanded to hold 2 bikes, and the relatively low cost. Used with a Curt hitch from this site on a 2017 Miata.
# 8
Swagman Trailhead Bike Rack for 4 Bikes - 1-1/4" and 2" Hitches - Tilting
This is a very solid product! I have used it for over a year now and love it! I have had up to 3 bikes on this without a problem and have traveled over 8 hours in the car one way with absolutely no issues. Many other bike racks like this one that I see on other cars look unstable this is not unstable in anyway. I did have to file some of the paint off of the rack to get it to fit in my 1 and 1/4" hitch but once that was done it has been perfect. I also bought the locking hitch bolt which is awesome too.
The good: Solid, heavy construction. Easy to use method for attaching the bikes. Includes adapter for different type / size hitches. Fairly easy to swing out of the way for hatch access (although it is heavy). Plenty of room between carrier and rear of vehicle. The meh: Requires the use of anti-rattle bolt. This means that one must carry a socket wrench to install and remove the carrier. Should use a torque wrench. The bad: Instructions are awful. To assemble, "only one bolt needs to be installed", but the photos are so poor that they are useless. Does not say that a second bolt has to be tightened. Pin and pin locks cannot be used because the anti-rattle threads cannot be removed and are too small diameter for a pin. Recommended Swegman anti-rattle lock is too long to fit on some factory hitches such as Jeep Grand Cherokee. Bike strap and connectors make placing the bike on the inside holder a chore.
# 9
Swagman XC2 Bike Rack for 2 bikes - 1-1/4" and 2" Hitches - Frame Mount
I like the overall design of this rack, but unfortunately after hauling a couple bikes around for a while the point where the crossbar connects has apparently rounded off so the rack swings back and forth. I've used rope to tie the ends of the rack to the car to stop this from getting worse, but it's inconvenient. Note: the hitch connection itself is good and solid, but the point where the crossbar connects to the bar coming from the hitch has gotten loose and there's no way that I can see to tighten it.
I own a 2005 Jeep Wrangler X with 31x10.5x15 oversized tires and wheels. I installed B6196001 HighRock 4x4 Oversize Tire Carrier by Bestop to carry larger spare tire. I needed a bike carrier that would carry our two crusier bikes and clear my spare tire. After measuring, I ordered: -> S64650 - Swagman 2-bike carrier -> 80300 - 7" Hitch Adapter 2" to 1-1/4" Trailer Hitch Receiver -> RM-061 - Roadmaster Quiet Hitch for 2" Trailer Hitches Our order arrived very quickly, etrailer.com upgraded the shipping. All these products arrived well packaged and without damage. In 15 minutes I had every thing assembled, installed on my Jeep and bikes loaded. The bike carrier is very well constructed, finish is excellent and easy to adjust. When adjusting wheel loops and loading bikes, make sure you pay attention to bike pedal position. I chose this extension because I did not want to use the adapter that comes with the bike carrier, I wanted as few parts as possible to keep rattles to a minimum and gives me more options for towing. The anti-rattle bolt/pin firmly secures the bike carrier to the extension and the Roadmaster Quiet Hitch keeps the extension adapter from rattling in the receiver. Road tested approximately 25 miles over rough city roads ( including railroad tracks ), county roads and highway. Bikes traveled very well without any rattles. I can remove my complete setup quickly, fold and put in rear of Jeep if desired. I am very well pleased with my purchase. Note to etrailer: Please consider offering Roadmaster Quiet Hitch in black to match receiver and accessories. Paul In the Land of Oz . . . Just South of the Yellow Brick Road!
# 10
Swagman Trailhead Bike Rack for 3 Bikes - 1-1/4" and 2" Hitches - Tilting
Draw-tite Sportframe Trailer Hitch Receiver Class I - 1-1/4 Swagman Trailhead 3 Bike Rack - Tilting The Draw-tite Sportframe class 1 trailer hitch and Swagman Trailhead 3 bike rack were ordered for a 2017 Honda Fit. The online order and shipping went just as expected. The trailer hitch and bike rack are very heavy duty. I recommend watching the trailer hitch install video before installing, whereas the video is very helpful. The bike rack has triangles that you can rotate to find the best fit for your bicycle's frame. The rubber straps are thick and secure the bicycles when you pull them tight. This bike rack will stay on the vehicle for 6 months each year. The tilt feature and folding arm feature are must haves for a smaller hatchback. I am pleased with this purchase, it appears to be good quality and good value.
Just as advertised. Sturdy and solid. Folds at both the top and bottom sections for easy storage. The tie downs are well positioned and minimize bike movement. Can't wait to get on the road with it.
# 11
Inno Fork Lock III Roof Bike Rack - Fork Mount - Clamp On - Aluminum
The NA391 roof bike rack is sleek and stylish looking. It's light and seems to be pretty aerodynamic. At the same time, it appears to be pretty sturdy. Once clamped to my INNO roof rack system, I can grab the track of the roof bike rack and pull back and forth enough to rock the whole car without it moving on the roof rack system. I would give it 5 stars but for what I believe is a design flaw that INNO seems to have overlooked. Due to the curvature of the roof on the Tucson that the Inno rack system is mounted on, the front clamp of the bike rack does not sit flat on the INNO crossbars. The bike rack comes with a spacer to use under the rear clamp to level the rack. But the bolts on the clamp knobs are too short to use the spacer. I don't understand how INNO could miss this design flaw in their own product. Even with just the thin strips of rubber spacers on the bottom of the rack on top of the rear crossbar is almost too much for the bolts on the knobs. INNO needs to look into this flaw and correct it.
I like the bike racks…I ordered two for my INNO roof rack load bars…good quality and reasonably easy to install. I did not realize etrailer also carried the same type of bike carrier that will slide directly into the T-Slot track, otherwise I would’ve gotten those instead…Oh well, that’s the way it goes sometimes.
# 12
Thule Gateway Pro 3 Bike Rack - Trunk Mount - Adjustable Arms
Still working great on my Hyundai Elantra sedan! It's used mostly to carry one bike, but have used it with three bikes with no problems. Easy to put on the car, and easy to store it in the car when not in use.
I did my research to make sure this 3 bike rack would fit my car. Unfortunately when it’s properly attached to my Honda Accord, the 3rd bikes petals rub up against my license plate and trunk therefore scratching my paint. Contacted etrailer and sent them pics. Very unhappy that they would suggest that I only use 2 bikes so it doesn’t damage my car. Defeats spending more $ on a 3 bike rack
# 13
Hollywood Racks Destination Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
The Destination bike rack works perfectly on my 2020 Pacifica and I have clearance going over speed bumps! I recently upgraded my bike to a Trek step through which hung too low on my old Thule rack no matter how the cross bar adapter was adjusted. Problem solved!
I realy like how it holds my bikes securly in place. I also like that (without the bikes) I can open and close the hatch on my 2014 Hyundia Santa Fe. I have a 2" receiver on my car. We went away for a long weekend from CT to VT and had no issues with it holding my bikes. Would definetly recomend.
# 14
Thule OutWay Platform Trunk Bike Rack for 2 Bikes - Adjustable Trays
Originally I was looking to put a hitch on my 2021 jeep renegade sport for a hitch mount bike rack, after seeing that I would either have to remove seam sealer and drill holes in my rear subframe (this is not a good option living in the rust belt), or remove my entire back bumper off and cut holes in it for the factory style hitch, and still have a rack that is illegal and blocks my license plate/brake lights turn signals I decided to look at different options. A roof rack is a little too high to lift a bike on comfortably. This thule outway platform 2 takes about 10 minutes to install correctly, and is solid and holds the bike securely, and the rack locks to the vehicle, and also the bikes lock to the rack no extra purchases required (comes with 2 keys and plastic spoiler supports). I have driven 80mph over potholes and bumps, also on extreme hills and has held securely.
Great product. Packaging came damaged but product looked ok.
# 15
Thule Gateway Pro 2 Bike Rack - Trunk Mount - Adjustable Arms
Exactly as advertised, transported 2 Trek bikes on on the back of my 2016 Toyota Avalon without issue - travelling from Boston MA to Green Bay WI. Outstanding price buying this item as open-box. etrailer's website is the best I could find on the web with name brand racks, automated compatibility vehicle check, and they they shipped overnight.
The delivery was quicker than I expected, but apparently the item was not checked before shipping. There was a key strap missing. I called customer service and they said they would send me a replacement part. If that goes well, I would move my rating to four stars from two.
# 16
Thule EasyFold XT Bike Rack for 2 Electric Bikes - 1-1/4" and 2" Hitches - Frame Mount
I purchased the rack and receiver hitch a year ago. Installation of the rack was made simple with the installation video that was specific to my vehicle (2020 Honda Accord). Literally took less than an hour start to finish. Only tool that I needed to buy was a torque wrench, which was about 20 bucks. It did require a very small cut in the plastic bumper that was accomplished easily with a keyhole saw. There was no drilling or other significant issues. The rack itself is awesome! My wife and I have two Lectric XP3 bikes. They weigh about 65 pounds each with battery. When we travel I revome the batteries to save a bit of weight. I have made two cross country trips (over 6000 miles) with this rack and have never had an issue. Literally every gas stop or hotel stop someone asks me about the rack and bikes. It really is that nice. My wife usually scolds me because we lose a 1/2 hour of travel time each stop to visit with complete strangers:) The rack is easy to install and remove on the receiver hitch. The lockout feature works great and gives a great deal of peace of mind. The bikes are easy to load. I don't use it, but there is a ramp that could make loading the bikes easier if a person couldn't lift the bike onto the rack. There are two arms the lock onto the frame of the bikes similar to the receiver hitch. Once locked down the bikes will not move. I would recommend ordering the longer ratchet staps if you have fat tires. I think they cost around 20 bucks but the longer straps allow for a little more flexibility in arranging bikes on the rack. I would strongly recommend this product and this company.
This product arrived in perfect condition in a sturdy box and arrived as expected. The description and photo were perfect. I am only 4'11" and I can lift and put this carrier on the hitch on our vehicle. It folds up which makes it easy to install. My husband did the minor assembly. We are impressed with how securely the rack is and comes with a ramp to help ease the bike onto the rack without lifting. Also, the rack can be tilted so the back hatch of the vehicle can be accessed without taking off the rack from the car.
# 17
Curt 2 Bike Platform Rack - 1-1/4" and 2" Hitches - Frame Mount - Tilting
I installed this rack onto a Curt trailer hitch which is mounted onto a 2017 Honda Fit. I have been using it intermittently for several months, probably about 5 times with one bike and twice with two bikes. I give some pros and cons below and then elaborate. Pros: easy to assemble, easy to mount and dismount bikes, easy to lock and unlock, how to put the rack into different positions is intuitive Cons: inconvenient to put the rack into different positions, inconvenient to mount the rack onto the hitch, rack protrudes about 15 inches from bumper when in flipped up position (seems very vulnerable to someone backing into it in a parking lot, very inelegant looking I say the repositioning is intuitive because there is really only one way you could possibly place the pins for each position. But removing and replacing two pins is much less convenient than turning a knob or a lever, like some racks do. Also many racks fold and flip in such a way as to look very unobtrusive when in non-use mode. This one looks like kind of a monstrosity. That does not really bother me but it might bother some owners. The part that does bother me is how far it protrudes from the car. I back into parking spaces whenever possible to avoid someone bumping into the rack and damaging it (which happened to a friend). My number one suggestion for Curt is related to mounting the rack onto the hitch. Make it easier to tell when the holes are lined up so that the bolt/pin will fit and thread. As it is now, if you insert the rack as far as it can go it is way too far in. Ideally, it would be exactly lined up. Failing that, maybe some kind of click or other feedback to know at least that you are in the neighborhood. It would also be great to have an attaching device that is easier to fasten and unfasten than is the bolt/pin. Tip for mounting the rack onto the hitch: I assumed that it would be awkward to hold, what is it 46 pounds?, while trying to line up the rack probe with the receiver. If you have a garage with exposed collar ties, my solution could work well for you. I looped a cargo strap over a collar tie. Then I hooked both hooks of a bungie onto that loop. The idea is that you hook one of the bike frame holders of the rack onto the bungie, suspending the rack a few inches off the garage floor. This takes most of the weight of the rack so that you can just pull up or down and forward until you line up with the receiver. Tip for mounting bikes. Don't put the little screw into the post that prevents you from completely removing the bike frame holders. Remove both holders. Position the first bike, slide the holder into place, position the second bike, slide the holder into place. I found this makes it much easier, because you avoid parts of the bike hitting the holder as you are trying to get the wheels into place. The trick is that if you are mounting only one bike, don't forget to put the second holder back on - or maybe just stick it inside the car right away.
# 18
Thule T2 Pro XTR Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
Great product, great company to do business with. etrailer is the best. Friendly, helpful and they made sure the bike rack was shipped immediately and it was delivered on time.
The quality of the rack is very sturdy and well built. I needed a rack that has a 12” spacing between wheels do to the baskets on each bike, and this rack delivered that. The issues I have with this rack are: I have a GMC Yukon suv and with the rack mounted I have to lift my two Lecritc 2.0 e-bikes, at 60 pounds each up over 24” to get it mounted. It sure could use ramps, which I know it did not come with. The clamp hold down does not work with fenders on a bike. It does not clamp very well on the cross bar (male and female) type do to the width and the angle of the cross bars. When clamping in front of the front fender makes the bike very unstable, and will require additional strapping and tie downs to secure the bikes. It claims it is for e-bikes, but only if it has no fenders. Nice rack, just not for me.
# 19
Thule OutWay Trunk Bike Rack for 2 Bikes - Adjustable Arms
Great bike rack. The cable and hook system is extremely strong and tight and being bike to open the trunk with the rack attached (but without bike) is a godsend for packing. Assembly is somewhat difficult due to Thule’s IKEA-style picture instructions. Watching the video is essential. Once assembled, however, attaching and locking the rack in place is pretty simple. Be sure to wash and dry hooks, bumpers, and car surfaces to avoid scratches!
The rear hatch mounted rack fit my X3 just as your website indicated - the technician who described how this rack would fit. I'm impressed with how well it is designed to be stable and to not impact the plastic spoiler above the rear window.
# 20
Yakima HangOut 2 Bike Rack - Trunk Mount - Adjustable Arms
When I started the search for a bike rack, I was so disappointed and upset to hear that I would need to install a hitch and spend even more money to buy another bike rack for my 2016 jeep renegade. I ordered this bike rack with a little hope but got a huge surprise! Not only is it super convenient and easy to install but I can fully use my trunk and not spend a ton of money!
Very nice, works well. The only thing that was an issue was with the "Anchor" part of assembly. The straps it came with were 2-3 ft. too short. So I had to replace/substitute my cargo straps for the Yakima top straps. Other than that, I'm pretty satisfied with this item.
What our customers are saying:
"I purchased a hitch, wiring harness, bike carrier and bike adapter for a newly redesigned 2007 Hyundai Santa Fe. Everything arrived in a matter of days and either fit or worked perfectly. Great prices, quality and service support. Rest assured, I'll be recommending you to anyone who asks. Thanks again."