Best 2000 Ford Windstar Trailer Suspension Parts

Some of the pieces in this kit are of questionable quality. In particular, the threaded center of the nuts are not round, and will not thread on to the bolt. The kit comes with 14 of these nuts, and 7 of them are unusable. This is unforgivable, considering the issue has been reported at least since 2023, as there is a review and accompanying photo on 05/16/2023. So if you buy this kit assuming the problem has been corrected, you will be mistaken. Other than this issue, the kit seems to be acceptable.

great construction, but the screw to connect to the trailer was not long enough.

Excellent service and prices. Needed to replace curved equalizer, shackles and bolts, nylon spring bushings, u-bolts, and wheel bearing seals on my sailboat trailer. etrailer had everything and shipped it fast. Staff at etrailer was excellent!

These were just what we needed for repairs on our 1983 stock trailer. The old parts were quite worn. We gave the trailer a face lift as well, and it should last another 37 years.

Direct replacement. Goods quality

I Waited Too Long to Replace Trailer Bushings -The past few years I would hear “clunking” sound (different than “squeaking”) from my boat trailer, but I got concerned this year as it seemed louder. -With the boat off the trailer I could see wear around the shackle bolts -I called eTrailer to order the parts and was helped by Kayla to order the bushings/shackles/bolts/nuts for my tandem axle trailer -After trying to press the bushings in I realized I measured poorly and had two different bushings, the equalizer had 1 size and springs had a different size. -Amanda helped me get the second set of bushings (delaying the project for 5 days…but my fault) Right or wrong: -I applied anti-seize compound to the shackle bolt threads -I pre-loaded the “wet” bolts with marine grease to fill them up before inserting them into the suspension, adding grease when everything is installed -I tightened the bolts very securely and they backed off the nut ½ turn to allow for suspension movement Lessons learned: -Look for different size bushings in equalizer/springs and measure correctly ID & OD precisely -It takes some time to do this job (about 4 working hours per side) so try to do it when you are not under pressure -If you want the re-paint some parts, allow for primer and top coat drying time, i.e. overnight which adds time to the project, but it comes out better -Have a big breaker bar & extension/enforcer to help get the nuts on & off. My ½” impact gun could not tighten them all the way -A large “C” clamp will press the bushing in smooth & straight instead of using a hammer & block of wood “caveman style” -Annually inspect your trailer suspension for signs of wear and listen for increased noise Thanks again to Kayla, Amanda and eTrailer for help with this project.

We purchased these parts for a custom build trailer for hauling heavy tool boxes over steep grades. Since completion of the build about a year ago, we have been using it and put a lot of miles on it. The hydraulic surge brake system makes it worry free. We can tow it behind different vehicles of differing weights and wheel bases and not worry about setting trailer braking, it is very nice. We will continue to use etrailer for our trailer needs.

Could you please share some info as to what is the hanger spacing measurements for the APT8 kit with 25-1/4" eye to eye springs? I've tried researching it but no luck. Would really like to get this welded on this weekend Thanks

New suspension parts made a real difference in trailer handling. Original shackles holes were severely elongated, spring eye mounts were also needing attention. Thank you, etrailer for the needed parts and support.

These parts were a perfect replacement for my old rusted u bolts. I would recommend buying flat and lock washers to place on the u bolts under the nuts due to the holes in the plates being big enough that the nuts get a little torn up when you tighten them, also the nuts it came with aren't lock nuts.

I have received significant support from e-trailer over the past 10 days as I have made several purchases for a new axle, springs, and hangars for my utility trailer. William and others have went out of their way to assist. I have been very satisfied with all products received. I will post another review when the trailer is completed.

Good kit with the necessary parts to replace leaf spring suspension. I welded the hangers rather than bolting them. The parts are not coated for the price point so you will need to paint them or they will rust immediately.

Excellent, had everything I needed and more for my trailer. Everything fit well!

I bought a axle, springs wheels, hubs etc. to build a utility trailer, I inadvertently had ordered incompatible hubs for the selected axle the person filling the order noticed this and contacted customer service to alert them of the issue who then called me to correct the problem. This saved me the time and expense of returning the part and delaying the project. great service, attentive, knowledgeable employees and great products. Thanks E trailer.

All parts fit my rebuild of new springs for my 1999 Bear trailer that my G3 Bassboat sat on for 26 yrs(used a lot for fishing on weekends)

Direct replacement, good quality

Just what we needed to replace the old rusted shackles when installing the new leaf springs.

I replaced the equalizers, shackles, bushings, bolts, and nuts on an old trailer. Everything fit properly without modification. Product quality was excellent.