Most Popular Fixed Ball Mount for 1981 Ford F-100, F-150, F-250, F-350

I installed the trailer wiring and a friend helped install the hitch. Etrailer website is excellent. I got the right items on time and the fit is better than my wife’s dealer installed hitch. Videos on the etrailer site are clear and correct. One caveat, don’t try installing the hitch without at least one other person and having a way to lift the car(we used ramps) is a great help. The only possible way etrailer could be any more helpful is if they could recruit some local shops that would be willing to do the installation. I especially like having my wiring in the passenger compartment when not in use. It keeps it out of the Salt here in the northeast.

I got a hitch for my Honda accord it was extremely easy to install took less time than they estimate after I installed it I bought a trailer and have hauled various things already with no problem I would recommend e trailer to anyone

My newer Chevy K3500 has a 2 1/2 inch square receiver so I was able too get rid of my 2" ball mount that was almost too heavy to lift and replace it with a new Reese tri- ball mount with a 14,000 lb Gross towing capacity and weighs less than 12 pounds. Thanks to Cathy H. and Chris W. at etrailer.com for finding the right equipment for my needs.

Despite some of the conflicting reports on here about the Reese Tri-ball Titan Hitch fitting 2011 and up Super Dutys I took a gamble and it payed off. It fits my 2012 Super Duty with no issue. I didn't have to grind the corners or take the sticker off or remove any paint. Thanks for the great customer service and answering my questions.

Installation photo

Worked flawlessly on our 1800 mile trip. Thanks.

A small shipping glitch , but they took care of it quickly

I had a great experience ordering from you. Your organization kept me completely up to date with the order & shipping process and delivered the exact products I ordered. Attached is a photo of the 16,000 lbs capacity hitch and 30,000 lbs 2 5/16 ball you sold me in use. The boat and trailer total about 12,000 pounds. Thanks again.

The hitch and ball mount are excellent quality. My concerns are twofold. The hitch is so heavy that I had to take it to my mechanic to have it installed. Minor cost and inconvenience, but the hitch for my previous F-150 was just as sturdy, but easy to install myself (albeit with higher ground clearance). My concern about the ball mount is that the factory told me erroneously that it could not be reversed for a drop, so I returned it. This order is for the replacement after I was finally correctly told it could be reversed and how to do that. Ball mount would have been a 3 for that reason, and overall hitch and ball mount quality a 5. So I averaged them.

I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.

High quality ball mount and they arrived at my doorstep within 36 hours of placing my order, how did you do that?

Works as intended - great value.

Arrived today. Fast shipping, and thank you for that! Seems to be a quality ball mount. Just what I needed to get the ball lower to tow my trailer. With this, now the top of the ball is at 16" where it needs to be. Custom built receiver on my old moving box van. Just need to weld on safety chain slots and paint it. Can't drop the lift gate with the receiver in (its pinned on both sides), but hey....I can tow now.

Tow infrequently; got new(to us) 2015 RAM 2500 pick up to tow our 38’ touring travel trailer. Have a HD WD hitch & adjustable sway control hitch set up we use for this trailer, but needed a drop hitch for our smaller Travel trailer& misc use haul trailer,,,,both much lighter & do not require the sway control set up. This drop hitch & ball fit the bill perfectly as the needed drop did not provide suffice t ground clearances to utilize the WD hitch mount setup (which was not needed) for those smaller loads. E-trailer worked w us to get the product we needed & an option that was inexpenve but sufficiently rated to pull our smaller trailers! Very happy our results !

Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.

The product is good but a bit tideous and after installing it my bracket fell and it was a pain to get replace it support made me buy the replacement pieces and the bracket didnt come with just the bolts, and at the end they told i have i had to buy the whole unit because based on their system my truck didnt have issues with installement and the manufacturer didnt supply that bracket cause it special order so in general i dont recommend in my choice better to get it welded.

First of all, the products you find at etrailer are not your garden variety, home depot kind of fair. Much higher quality and grade/weight ratings. So to be able to get hard to find items and then by orderring at least 100$ worth of stuff also get it delivered free in 4 days, is awesome. The prices are incredible too.

My 2018 F350 chassis cab has a Knapheide service body with a Buyers hitch installed by Knapheide. It is bolted and welded in place. Unfortunately, it only has a 2" receiver. To have them change to the 2.5" receiver hitch would cost me approximately $1200. The 20,000 lb. Curt replacement hitch would not work on this truck with this bed. The Buyer's hitch has a weight rating of 16,000 lbs. and 1600 lb. tongue weight. Fortunately, Curt has come through again for me with this ball mount. I bought two: one for my 2" ball and one for my 2-5/16" ball. They are great and the drop is very close to what would be perfect. Your towing set-up is only as strong as your weakest link and I now know the the ball mount is definitely not my weakest link. One note to Curt: When you put the stickers on your ball mounts, make sure they're clean. Before I even towed, the thick Curt sticker on both ball mounts started coming off. It feels like there is some kind of coating possibly on the mount and then the decals were applied. I tried pressing them both back on but I doubt they'll last the rest of the week. But as always, Curt has built me a great product for my needs. I'm a one man landscaper business but have spent quite a bit on Curt hitch products because they WORK.

I purchased Curt's 6" drop ball mount for my 2012 Jeep Wrangler Sport which is not lifted but has 32" tall tires. The utility trailer I plan to purchase recommends a 12" tongue/ball height for level towing. The Curt 6" drop ball mount places my tongue/ball height at 13.5" which is acceptable. The bottom of my tow ball mounting nut is now 12" above the road surface. Plenty of clearance for safe towing. I'm very pleased with the quality and functionality of my Curt ball mount. I'm looking forward to purchasing a utility trailer soon. I think it will tow very nicely using my Curt 6" drop ball hitch.

I bought this on my knowledgeable brother's advice - he gave me the exact order number and link to buy from etrailer! I had it installed locally, without complications. I use my truck mostly to haul my horse or my friend's two donkeys in my 14-foot stock trailer. I have no complaints, the hitch does what it's supposed to do.

I needed the dropped ball for my motorhome to tow my Jeep. More importantly I needed the long shaft into the receiver for a device that bolted onto the shaft. This hitch worked perfectly in all regards. High quality and fits perfectly.

Product was shipped well packaged in a box to avoid damage. Perfect height and length for my F150 front receiver. This should make moving my trailer in tight spaces easier.

This is really nice. Beveled edges so it slips into receiver hitch so sweet. Beautiful welds heavy weight mount for my weigh safe ball. I bought a 10,000 lbs hitch and I wanted a draw bar with the same type rating. Now the only thing limiting my trailer capacity is my truck's ability to tow, not the hitch, bar or ball.

I purchased a Ranch Hand rear bumper for my 2500HD but wanted to retain the use of a receiver hitch. The ball mount would need to extend 8" from the pin hole to even reach the edge of the bumper. This BM29 ball mount works out perfect. The welds look great and the finish is just fine. The only complaint I have is they gained a little length by moving the pin hole a little closer to the end shortening the insertion amount slightly. Not a big deal, it is just noticable next to the other mounts I have at the house.

I have used B&W hitches for many years and I've been very happy with the quality of their products. etrailer makes it easy to shop for these hitches since the B&W site is terrible. I was able to find the correct size and all dimensions were listed clearly. Thanks again!

Product is extremely heavy duty. much more than I will need, but I appreciate quality made is USA products. Etrailer packaging not so great. Box was torn by weight of this item, which caused a chip in the finish of the item.

Retail type stores only carry mainstream items so when I needed a special length ball mount for my 2011 Traverse I found the size and quality with Curt Products .

Recently bought a Kubota RTV x900. The receiver is located under the bed. With the extra long ball hitch drawbar I can easily get to the drawbar and use a clevis to hitch my 5ft. wide mower or attach a ball and use the trailer. The pictures will illustrate the length of the drawbar which makes access very easy. The product is heavy duty and well made. Ordered this product on Thursday morning and it was delivered the next day, Friday afternoon. Customer service was helpful, will use etrailer again. Thanks

Perfectly as described, Box was a heavy hitch and the box must have been damaged in shipping so it was a little delayed. You can't mess up a forged hitch it still is in excellent condition.

I bought this to use it for the 3 inch rise it provided. I have a lowered truck and towing my car carrier would prove to be difficult at times. The 3 inch raised that this provided made the trailer stay in a more manageable position. The heavy solid metal construction is of extremely high-quality. I would not have any hesitation towing something at the rated 16,000 pound capacity.

My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks

We have a Pink Tractor (google Mom's Pink Tractor) that we pull to events, mainly in Ks, Ok, Mo, and Ne. We have around 35 events a year we take the tractor to to promote breast cancer awareness. The other day my wife and I were leaving for an event, i had let a friend borrow the hitch to see how he liked it. In less then a mile from the house my wife started complaining about the trailer jerking. That is coming from a lady that really was upset when I paid that much for a hitch. She told me to stop and buy one. (a long and expensive trip, we had to stop at a casino so she could rest her neck) I could write a review with a lot of trailer talk, but, this story tells the story.

This ball mount has served it purpose well. I purchased a new travel trailer that is heavy enough to require a weight distribution hitch when using the factory installed Class III hitch on our Dodge RAM 2500. I decided to upgrade to a Class V hitch combined with this ball mount to take delivery of the TT in order to defer decisions about a WD hitch until the actual load conditions were known. The hour trip home with this setup worked very well. Once the trailer was outfitted I was able to determine the actual tongue weight of the loaded trailer and I decided to purchase an appropriately sized Reese Straight Line WD hitch. However, this ball mount comes in handy for moving the trailer short distances without hassling with the WD system. The purchase experience through etrailer.com was first rate.

I was surprised at the heft and quality of the ball mount. Shipping was fast, communication good, easy and informative website to use. Thanks etrailer, you have earned a new customer!

Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.

I searched the internet to put a hitch on my 2016 Chevy Equinox and found an instructional video from eTrailer.com where they installed on my exact car. I decided to go with eTrailer.com because they answered all my questions and because of the video-I support businesses that go the extra mile with these videos. Shipping was quick and well tracked, however, the box was flimsy and the one end of the hitch had come out of the box side and the ball mount could have easily come out of that hole during shipping. If I were eTrailer.com I'd charge an extra couple of bucks for more sturdy boxes-people will still buy as eTrailer is a well-trusted brand and this would overcome a lot of the negative reviews you'll see on their site about this shipping issue in their own reviews :-) I installed the hitch by myself (definitely recommend help as two people holding it up to the frame makes attaching 100% easier) in about 45 minutes total (out of the box, read instructions, review video again and installation complete). All hardware went on with no issues. Great quality hitch! I also bought the lesser expensive wiring assembly because most recent equinox's come hitch ready with pre-wired assembly in the left side compartment-snap and done. Picked up a new trailer at Home Depot within days and drove 5 feet and the clacking was horrible. I had always had a welded hitch before buying a hitch that took a ball mount. I really thought something was wrong and when I searched the internet that night it turns out this is very common. However, all you need is some sort of hitch "silencing" device. The number of options will drive you mad but I went with the Roadmaster Quiet Hitch and it did the trick for much less than most of the other options. If I were eTrailer.com I'd have that as one of the RECOMMENDED add-ons and explanation why its super-worthy when customers are buying a hitch. Would have saved me the time and hassle of dealing with it later and the extra shipping charge for buying after the fact when I got free shipping for the other items the first time :-) All in all, I'm super, super happy with my hitch, wiring assembly, ball mount, ball mount locking pin and the hitch silencer. Buy with confidence from eTrailer.com Paul R., Syracuse, NY

I bought the 1 7/8 and 2 inch combo so that switching between the two is as easy as pulling a pin. However, I didn't realize that I had to install the ball. I had to find someone with a wrench and torque wrench big enough to do it. Otherwise, excellent quality as usual from E-Trailer.

Great Value for the Money