/
Draw-Tite/
Fixed Ball Mount/
Fits 2 Inch Hitch/
Class III/
7500 lbs GTWItem # 2923
Orders above $50 qualify for Free Shipping
Sturdy steel ball mount with hollow shank measures 8-1/2" from center of hitch pin hole to center of ball hole. Angle-cut shank slides easily into your hitch. Powder coat finish over a-coat base provides excellent rust protection.
Features:
Specs:
Video of Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today on our 2013 Honda Odyssey, we'll be test-fitting the Draw Tite ball mount with three quarter-inch rise or two-inch drop part number 2923. To begin our test-fit we'll go ahead and get our hitch height. This is measuring from the ground to the inside top edge of our receiver tube. We have a hitch height of two inches. Now we'll go and pick our ball mount and install it in the drop position. We'll just line up the pinhole and then insert our pin and clip.
Our drop position measurement is nine-and-a-half inches. This is measuring from the ground to the ball platform. Make sure when measuring your trailer height you do so when your trailer is level. You want to measure from the ground to the bottom of the coupler. If your measurement matches ours, then this would be a correct fit for you.
Now we'll take our ball mount and switch it to the rise position. We'll just line up the pin hole and then install our pin and clip. Our rise position measurement is 13 inches. If this measurement matches yours, then this would be a good fit for you. That completes our test-fit of the Draw Tite ball mount with three quarter-inch rise or two-inch drop part number 2923 on our 2013 Honda Odyssey..
Average Customer Rating: 4.9 out of 5 stars (753 Customer Reviews)
Sturdy steel ball mount with hollow shank measures 8-1/2" from center of hitch pin hole to center of ball hole. Angle-cut shank slides easily into your hitch. Powder coat finish over a-coat base provides excellent rust protection.Does what it is supposed to do. 696861
I was just rear ended in my suv. During the accident the Hitch ball mount was bent. As usual I visited the etrailer web site so I could purchase another one. That has to be one of the nicest quickest web site I have been on. Thank you it was extremely easy to find and order. Delivery was very quick. Thanks again. 676916
Solid, heavy ball mount. 441408
Sorry I did not write back sooner, it’s has been a busy October. I really like everything that I bought. So far I have only used the hitch for my bike rack. But I am planning on using a friends trailer for some yard work and home project jobs. I am a welder by trade and everything is well built and as expected, no issues with anything. I especially like how easy the electrical was to connect to the factory harness. My friend who owns the trailer recently bought another truck and with my recommendation he also purchased a trailer hitch and the other parts he needed from etrailer.com. I have recommended etrailer.com to literally everyone I know. I really like the products and will be a return customer.
Awesome product easy to install !!! Saved me over $800 by doing it myself as the dealer wanted $1058 for the same bolt on set up... awesome price guys thank you very much.... 518457
Just what you need for small drop 201735
excellent. would buy again
Purchased a can of BP Blaster penetrating spray the day after I ordered the parts. I sprayed the weld nuts several times while waiting for the parts to arrive and it seemed to help loosen them up. My order arrived on time and I installed the hitch the next morning. I installed the hitch by myself ( I'm 67 years old), and while I admit that an extra set of hands would have been very helpful, the install was easier than I anticipated. I had all the parts I needed, the instructions were easy to follow and the online video was very helpful. I purchased the hitch in order to tow a trailer with a ton of wood pellets, instead of getting 1/2 a ton at a time (the capacity of my truck). Hopefully these products will solve my problem, only time will tell. 392664
Fastest delivery I have ever had. Ordered Wednesday at 5PM, arrived Thursday at 3PM. I'm only a couple hundred miles from Wentzville, but still, excellent. The hitch receiver (2008 Pilot) installed quickly and easily. No need to remove spare or lower muffler. I supported the left end on a large cooler and quickly maneuvered the right side above the tail pipes. The mounting holes were right on target. I had to tap mine to remove rust, but that's easy as well. The wiring harness was also a snapto install. Simple to plug into existing fitting and the wiring box tucked away nicely beneath the trim as advertised. There are options about what to do with the wiring tail and trailer connector. I chose the method shown in the video...leave it rubber-banded in the storage well. Others have run it outside through available holes, but I did not want to leave it exposed to road grime. etrailer's videos were very detailed and shown on my specific vehicle for both the hitch and the wiring harness. Good values as well. If I were Draw-Tite (or Curt) I would include a complementary rubber plug with their logo...cheap advertising. 430539
All products holding up well. Easy install, good quality. Works as advertised.
Awesome great fast delivery! 571234
Product as advertised. Wished I'd paid more attention to what was included and not included. Seller web site did a good job indicating other suggestions on what would go with what you were viewing. So much so, I became dependent on it, and over looked the fact that the pin to hold the ball mount was not included in either the receiver or ball mount. I overlooked this and had to go out and buy this somewhere else. Other than that ordering was easy, and I received everything in a timely manner. It's worth noting that their tracking was dead on as well. It's nice tracking the progress of a package you are waiting for so you can plan your installation. And again, they do a nice job of following up letting you know they received, shipped the order and a link to follow it in transit. 147675
Works fine 129332
Works great
Great I didn't know a class 3 hitch needs a 1" ball thread. Most balls Iv'e seen have a 3/4" ball bolt or thread 59117
It works great, No problems
Very nice hitch. This is my third hitch purchase from etrailer.com and as usual, delivery was fast and the install went smoothly. The videos and user comments were very helpful. My vehicle is a few years old so the suggestion to chase the 8 mounting nut holes was spot on. There was a lot of mud and dirt which easily came out but would have been a pain to do while mounting the hitch. Also, the suggestion to spray down the rubber exhaust hangers and muffler heat shield bolts with penetrant (WD40) helped as well. The recommended draw bar and 4-wire harness also mounted beautifully. Got to love those factory installed rear wire harnesses which allow plug-in trailer harnesses on the Honda/Acura products. Total install took about 90 minutes which I think will be typical for a DIY'er who sprays down the bolts, chases the holes and without rushing or using air tools. Will buy again from etrailer.com 60422
A serious hunk of steel! 732092
Solid, heavy duty. 729875
Great product, great instructions. Got it done in 40 mins 728081
All good. A+ in every regard. Tough as nails. Still in use and will be for quit some time, I'm sure. 722753
Did the job. Easy install. 722175
Well made and easy to install,customer service wasegrrat 720528
Product was very good, installation was simple enough. This is the second hitch assembly I have purchased from you, both have been excellent. Just one problem, the retaining pin that holds the hitch in the receiver is to short. Making it very difficult to clip the pin into place. Thanks 719241
If a standard hitch pin like # e98880
etrailer.com Trailer Hitch Receiver Lock - Flush Design for 2" Trailer Hitches
$14.92 or # PC3
Pin and Clip For Class III, IV and V Trailer Hitch Receiver
$3.18 isnt easy to secure, an extra long hitch pin like # e98881
etrailer.com Trailer Hitch Receiver Lock - Extra Long - Flush Design for 2-1/2" Trailer Hitches
$14.90 could work well for you. This hitch pin is designed for 2-12 inch trailer hitches, but is 58 inch diameter and will work in a 2 inch hitch as long as you have clearance for the longer pin.
Everything I have ordered and received from etrailer has been 5 star great. 718051
I am always very happy with the quality and service at etrailer. I will purchase again! 717378
Had these for over a year which translates into one Maine winter and two extended off road hunting trips. The mud flaps are still on which is very good considering that they were put on in a hurry after dark. They do help prevent mud and snow buildup. Also dress up the vehicle a bit. 717223
Got this primarily for a hitch mount bike rack so have not used it for towing and did not need a wiring harness. The hitch was very easy to install. There was no cutting or dismantling necessary on my Jeep Laredo. The hitch has sufficient ground clearance for normal off road use. Definitely recommend it for this vehicle and application. 717222
Better quality at 7500 lb capacity than Harbor Freight's 5000 lb model. Did not expect pin and clip.. Thanks 714340
Customer Support was excellent. Products fit as good as factory and a whole lot less expensive. Installed in a couple of hours with a little help from a friend. The hitch is pretty beefy and I needed a little help holding in place. Other than that everything bolted right up. Nice heavy duty bolts and thick wafer washers to insure it won’t come lose. The hardest part was cutting the plastic factory shielding underneath around the hitch. Great product. 715369
Trailer ball mount was a good price and does the job! 705872
EZ installation, plan on towing my 1932 plymouth coupe to car shows around the state. 707090
I was very impressed with Carol. She made sure I ordered the correct product, because I ordered the whole package (ball, hitch and joint) thanks 703811
It's perfect for the application I'm using it for 698989
Just bought a Draw-Tite Receiver for my new Ford Ranger. The hitch was delivered in 2 days and fit perfectly. etrailer provided instructions and offerered additional help if needed. I recommend etrailer! Aside from the great service provided by etrailer, the Draw-Tite hitch fit perfectly with easy installation - 20 minutes by myself with jack stands and c-clamps. The receiver hides under the bumper just as I would have wanted. 696564
Great products, easy to follow videos, super helpful staff Thank you Ashley for your help with the order. 699104
Everything looks good in the shipping package. Package arrived the day I was told it would arrive. Very happy. Thank you. 696916
good price quality unit shipped fast. 694250
I just used it once but they didnt dissapoint. Theyre storaged away until further use 693471
I haven't installed the hitch yet but it appears to be very well made and heavy duty, which is what I wanted. The welds and paint all look great and I'm sure it'll be durable for years. Great product. I would recommend etrailer to others. Thank you. 691899
Works good, lasts a long time 691313
Great product and can not go wrong with Draw-Tite. 690044
I like it 688820
Great overall! 683987
Perfect fit on 2018 Nissan Frontier 688655
Quick delivery, excellent instructions, great service, installed and fit as advertised. What more can you ask for. 688611
Was easy to put in and the plug in wiring was a snap. Very happy with the purchase. Now I can bring my daughter to college with out having to bring 3 or 4 cars. 684006
Easy to install, directions were perfect, it's held up to the elements. I would buy again. 680253
I purchased a hitch, ball mount, ball and wiring for my Frontier. I thought your people were very pleasant. professional and helpful. I did have an issue with power to my lights but after watching one of your video instructions, I realized that I needed to purchase some additional in cab wiring that was shipped promptly. Just installed it and everything works perfectly. By buying your products and doing it myself, I saved about $150. Nice! Thanks 681341
Great price, great delivery time, and everything was delivered complete. UPS delivered the package is very poor condition, but no damage to product (hard to damage steel). 679446
I have purchased equipment from etrailer three times, and each time the service, product, and speed of delivery was fantastic. On my last order a customer service representative noticed that I had accidentally ordered two of the same part and called me to ask if that was done by accident or on purpose. Amazing service!!! I will be a life long customer. 680865
Not crazy about the clip in the 5/8" connecting pin, does not seem to secure enough for me. I ordered a locking pin to make a better connection. 679119
Exactly what we use and less that the big box stores and so easy to order online compared to going to the store. 678689
Receiver arrived as expected. Appears well made. 677359
Arrived on time...perfect fit.. 677168
Ask the Experts about this Draw-Tite Ball Mounts
Do you have a question about this Ball Mount?
Do you have a question about this Ball Mount?
At etrailer.com we guarantee:
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.