Junction Box and Installation Kit for Autowbrake Trailer-Mounted Electric Brake Controller

See what our Experts say about this etrailer Accessories and Parts

• Can the Autowbrake Electric Brake Controller Be Used on a 5th Wheel Trailer
  Yes, it is possible to use the Autowbrake Electric Brake Controller # 3430001 on your 5th wheel trailer being towed by your 2013 Ram 3500. The Autowbrake Electric Brake Controller # 3430001 wires to the junction box on your trailer and will work for your 5th wheel as long as it does not have more than 3 axles. If your 5th wheel does not have a junction box, you can use the Junction Box and Installation Kit for Autowbrake Trailer-Mounted Electric Brake Controller # 3430001-JBK.
  view full answer...
• Dimensions of 3430001-JBK Trailer Wiring Junction Box
  The junction box in the Installation Kit for Autowbrake Trailer-Mounted Electric Brake Controller part # 3430001-JBK measures 7" long x 3-1/4" wide x 2-3/4" tall. The overall length with the with mounting flanges included is 8". The distance between the mounting holes on center is 7-3/8". The mounting flange dimensions are 3/4" wide x 1/4" thick.
  view full answer...
• Recommended 7 way Connector for 2017 Dodge Grand Caravan Using Autowbrake
  The Autowbrake # 3430001 is a great choice! To add a 7 way to your 2017 Dodge Grand Caravan you'll want to use the # ETBC7L, since it doesn't require the wiring of a brake wire into the vehicle like the # ETBC7. You will still need to run a wire for the 12v power, but other than than it's going to be really easy to install since it plugs into your existing 4 way. To complete installation of the Autowbrake I recommend using the Junction Box and Installation Kit for Autowbrake Trailer-Mounted...
  view full answer...
• Junction Box and 10' Wiring Pigtail Availability
  The etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box # e99011 has a 6' long harness including the wiring inside the junction box. We do have a separate Junction Box # 3430001-JBK you can combine with the Hopkins 7-Way Molded Trailer Wire Connector # HM20048. This harness is 11' long which will give you approximately 10' of cord outside the junction box.
  view full answer...
• Parts Needed to Install Autowbrake and 7-Way for Towing with a 2016 Toyota RAV4
  To use the Autowbrake with your 2016 Toyota RAV4 you need the following parts: 7-Way RV Upgrade Kit - # ETBC7L Curt No-Drill Bracket - # C57202 Autowbrake Electric Brake Controller - # 3430001 Junction Box and Installation Kit - # 3430001-JBK The 7-Way kit plugs into your 4-Way and then has a power lead that connects to the battery on your RAV4 which is needed for the Autowbrake, and the Curt bracket is needed to hold the 7-Way plug near your hitch receiver. Then the junction box gives...
  view full answer...
• 7-Way Connector and Wiring Configuration When Connecting To Junction Box On Trailer
  It really comes down to the 7-way and wiring you are using. You saw the Hopkins 7-Way RV Style Connector # HM20087 which uses the following wiring configuration. White: ground wire Red: left turn/brake light Brown: right turn/brake light Green: tail lights Yellow: reverse lights Blue: electric brakes Black: auxiliary power We also have the Hopkins 7-Way Auto Blade Style Connector # HM20041 that uses the more common color configuration. White: ground wire Yellow: left turn/brake light Green:...
  view full answer...
• Junction Box and Parts Needed to Add 7-Way Round Connector to Tractor
  I believe what you're needing is the Junction Box and Installation Kit # 3430001-JBK along with the Pollak Heavy-Duty, 7-Pole, Round Pin Trailer Wiring Socket # PK11720 and then 8' - 10' of the Deka Wire - Jacketed 7-Wire # DW04914-1 (sold by the foot). Typically the junction box is located on the trailer side of things so there aren't any kits that come with the tow vehicle connector, but this combination should do the trick! The junction box comes with all of the connections you need...
  view full answer...
  
• How to Wire a Freightliner 7-Way to Match Utility Trailer 7-Way Functions
  The best way to make your Freightliner compatible with a trailer 7-Way is to test the functions with a circuit tester # PTW2993 and match sure they match. I'm attaching pin-out diagrams of both the trailer and vehicle 7-Ways that you can use as a guide to make your connections - just be sure to wire everything up by function and not by the wire color. You will be able to gain access to the wiring connections through the back of either 7-Way, either by moving the sleeve out of the way or...
  view full answer...
  
• How To Hook Up Lights On a Flat-Bed Without Splicing
  In order to achieve your goal of not splicing into the factory trailer wiring harness we are basically going to create a wiring harness for the flatbed which would plug into the factory trailer connector. In order to do this we are first going to want a junction box, part # 3430001-JBK. Once we have the junction box we can then run the wires from the headache rack and tail lights to this with part # 16-4B-1 (per foot). After this is completed the only other thing we need to do is attach...
  view full answer...
• Adding 4-Way to R-Pod for Light Kit on Bike Rack
  The Cargo Carrier Light Kit # 52014 is a good light kit but I you might consider looking at the Curt Auxiliary LED Indicator Lights # C53201 instead because they install by via adhesive instead of brackets and the lights have connectors that will be a little easier to disconnect. When it comes to adding a 4-Way wiring to the back of your R-Pod I recommend using the Junction Box Kit # 3430001-JBK on the tongue of your trailer. This gives you the ability to cut and splice the original wiring...
  view full answer...
• Recommended Replacement 7-Way Trailer Connector and Junction Box
  To wire in a new 7-way connector to your 5th wheel trailer you will want the Junction Box and Installation Kit item # 3430001-JBK and the 11' Hopkins 7-Way Molded Trailer Wire Connector item # HM20048. This kit comes with ring terminals, heat shrink wrap, and a junction box. The box will allow you to secure your 5th wheel's wiring in one water tight organized location. The 11' foot 7-way cable will give you flexibility when deciding where to mount your junction box. We do not have any...
  view full answer...
• Parts Needed To Rewire and Add New Lights to a 7 X 16 Utility Trailer With Electric Trailer Brakes
  Here is a list of the parts you will need to rewire your 7' X 16' utility trailer. I have added the breakaway kit as it will be required by law as your trailer does have brakes. Hopkins 7-Way RV Style Connector # HM20087 etrailer Trailer Wiring Junction Box # 3430001-JBK Optronics Trailer Light Kit # TL16RK Bright Way Push-to-Test Trailer Breakaway Kit # 3802346 Jacketed 2 Wire (Brake Wire) # 12-2-1 (sold [per foot)
  view full answer...
• Trailer Wiring Recommendation for 4-Way Wishbone Replacement on 1997 Car Hauler
  For a standard wishbone harness that carries the trailer light functions I recommend the 25 Ft 4-Way Trailer Wiring Harness # A25W2GWB. This has 2 different leads for both the running and ground functions so you can easily route those down each side of your trailer. If your trailer also has brakes then you need some additional wiring parts as the trailer brakes will be on their own circuit. For this you'll need harness I mentioned above along with the following: - 7-Way Molded Trailer...
  view full answer...
• Parts Needed to Install New Trailer Plug and Junction Box on Trailer
  I have a solution for you, and it sounds like you're maybe looking for some sort of plug and play option that you can use as an extender into the junction box, but that does not exist. Your best bet is just to cut the plug on your trailer off and wire the loose wires directly into the junction box; you'll then run a new plug out of the junction box to add the new trailer wiring plug. I recommend using the Junction Box and Installation Kit for Autowbrake Trailer-Mounted Electric Brake Controller...
  view full answer...
• Parts Needed To Add Electric Brakes Onto a 3,500LB Dexter Axle Without Brakes
  The Dexter Electric Trailer Brake Kit # 23-26-27 is the correct kit for your Dexter 3,500lb torsion axle studs. This includes both the left and right hand side brakes for one axle. It does not include a hub. I do recommend looking at the Dexter Nev-R-Adjust Electric Trailer Brake Kit # 23-468-469 instead as the brakes adjust while you drive saving you on having to adjust the breaks as they wear. This also maintains a more constant brake feel with less adjustment required on the vehicle...
  view full answer...
• Parts Needed For Wiring Electric Brakes On a Tow-it-All Car Dolly
  Since your Tow-it-All car dolly has electric brakes you will need to have a 6-pin or 7-way blade connector for your dolly. With electric brakes you are required to have a Bright Way Push-to-Test Trailer Breakaway Kit # 3802346 connected to a charge line. This will activate the trailer brakes in the event of a breakaway. Here is a list of all parts you will need. Bargman 7-Way, RV-Style Connector # WG54006-043 etrailer Trailer Wiring Junction Box # 3430001-JBK Bright Way Push-to-Test Trailer...
  view full answer...
• Bolt On 3,500LB Trailer Axles For a Home Made Specialty Trailer With Electric Brakes
  All of our spindles like the #84 E-Z Lube Spindle # TRU74FR are going to be a weld on application. We do have the Timbren Axle-Less Trailer Suspension System # A35RS545E that allows you to bolt on the assemblies. This will come with the drum brake hub and electric trailer brakes. It uses a 5 on 4-1/2" bolt pattern which is most commonly used with the Karrier ST205/75R14 Radial Trailer Tire with 14" Galvanized Wheel # AM32156. We do have the 7-Way # H20046, Junction Box # 3430001-JBK, and...
  view full answer...
• Parts Needed to Add Electric Brakes to a 6x10 Trailer
  There will be a few parts needed to add electric brakes to your trailer. First, you will need to have a flange on the axle that a brake would bolt to. If you do not currently have this flange, you will need to add something like the Brake Mounting Flange # 4-35. This is designed for a 2 3/8" axle and will have a standard bolt pattern for a 3,500 pound braking set-up. With that being said, the etrailer.com # AKEBRK-35-SA will bolt directly to the # 4-35 with the # BRKH10B mounting hardware....
  view full answer...
• Parts Needed To Wire a Tandem Axle Trailer With a 7-Way and Full Length Ground Wires
  What you are looking to do is acceptable. Here are the parts I would use working on this type of project. The 25 Ft 4-Way Trailer Wiring Harness # A25W2GWB has full length ground wires which will run down the side of each frame and carry the wiring for the tail lights and running lights. You will be able to cut off the 4-way and attach the wiring to a Junction Box # 3430001-JBK. The junction box includes ring terminals for connecting all the wires for the lights, brakes, and a 7-Way Cable...
  view full answer...
  
• Parts Needed For Installing Electric Trailer Brakes Onto a Trition UT16 Tandem Axle Utility Trailer
  It would appear your Trition UT16 utility trailer will have axles using the standard #84 spindle dimensions. You will want to verify this is what you have by disassembling one of the hubs and measuring the spindle, see image below. The spindle will be 1.063" in diameter for the outer bearing, 1.378" in diameter for the inner bearing and 1.719 in diameter for the grease seal. You will also need to measure the mounting holes for the brake flanges. The mounting holes should be spread 2-13/16"...
  view full answer...
  
• Wiring Needed For Adding Electric Trailer Brakes To a Utility Trailer
  It sounds like the Universal Installation Kit # ETBC7 might be what you are needing for your Jeep. This kit includes the wiring for the 7-way and Brake Controller # RED52VR along with a 20, 30 and 40 amp circuit breakers. Otherwise you would just have to get a 40Amp Circuit Breaker # PK54240PL to use with the Kit # 331-CBK30-EB. For the trailer you will need a Hopkins 7-Way RV Style Connector # H20046, Junction Box and Installation Kit # 3430001-JBK, Breakaway Kit # 3802346 and 12-Gauge...
  view full answer...
• Replacement Trailer Brakes For 2000 Damon Camplite Pop-Up Camper With AL-KO 8440 7" Drum Brakes
  Your AL-KO 8440 drum tells me you have a 7" brake drum with a 5 on 4-1/2" bolt pattern. This will need 4 of the Easy Grease Trailer Hub and Drum Assembly # AKHD-545-2-EZ-2K if you are needing to replace the drums themselves. For the brake assemblies you will need 2 of the Brake Kits # AKEBRK-2. We do have the Mounting Hardware # BRKH7 for the brake assemblies as your hardware may not be in the best condition with the age of the 2000 Damon Camplite pop up camper. We have 12 Gauge Wire...
  view full answer...
• Parts Needed To Install Electric Trailer Brakes On a 2023 Carry-On 7x14 Single Axle Utility Trailer
  First you will need to verify if your 3,500lb axle on your 2023 Carry-On 7x14 trailer has the Brake Mounting Flange # 4-35 behind each of your hubs. If you do not you will need to take your axle to a trailer shop to have the flanges mounted on each side. If you already have the flanges here is a list of the parts you will need to add electric trailer brakes. Electric Trailer Brake Kit # AKEBRK-35-SA qty 1 Trailer Hub and Drum Assembly # AKHD-545-35-EZ-K qty 2 Junction Box and Installation...
  view full answer...
• Converting a 1995 Jayco Eagle 12 UDK To Use Electric Trailer Brakes
  First you will need the Electric Trailer Brake Kit # 23-47-48 to replace your hydraulic assemblies. We have the Dexter Trailer Hub and Drum Assembly # 8-173-16UC3 to get you a 4 on 4 mounting pattern. You will need to disassemble one of your hubs to verify it will fit the new hub as your axle is produced before they maintained records for their axles. This hub uses inner and outer Bearing # L44649 which is 1.063" inner diameter. For the wiring you will go from the Hopkins 7-Way RV Style...
  view full answer...

Do you have a question about this Accessories and Part?