Replaces a lost or broken operator and knob on your Ventline Ventadome RV roof vent for motor homes and enclosed trailers. Properly sized mounting screw is included.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today on enclosed trailer we'll be installing the Ventline replacement operator with knob and screw for Ventline Ventadome trailer roof vent with metal dome. Part number BV0115-04. We'll also be installing the replacement dome assembly for the Ventline Ventadome trailer roof vent. Part number Bv0534-00. Now you'll need to first take apart the interior portion of the vent. There's four screws that hold the outer trim piece on.
You want to be extra careful here, as the plastic becomes very brittle as it gets older. Next there's two screws, one on the front and back, that hold the screen in place. These are small Phillips head screws. With that done, we'll go ahead and set the screen down out of the way. Next, you'll remove the two screws that hold the operator arm in place. You'll then slide the operator arm out through the slot.
We'll then take the new operator arm, slide it back up into place, and put the two screws back in, holding it to the frame of the vent. Next, we're going to need to go up on the roof of the trailer. Now we're ready to install the new cover. Just slide it in from one side and as you're doing that you want to make sure that the actuator arm slides through the round portion and then up into the channel. Now, it makes it a little easier if you have someone down in the trailer to help guide this through, or to raise and lower the actuator arm if need be. Now, we'll go ahead and lower the lid all the way down where we can bend the tab over. You want to make sure that both sides are bent far enough that there's no chance they can slide back out of the track.
Next, we'll need to go down into the trailer where we'll be attaching the friction clip to the operator arm. That way it can't come off of the new lid. You want to make sure that the concave side of the clip bears against the dome bar. If you've attached the handle temporarily, you will need to unscrew it so we can put the screen back up into place. Once the screen's back up into place you can go ahead and put the handle back on. Finally, we'll put the trim ring of the piece of plastic that goes around the outer edge with the four screws.
With that, that's all there is to it, to replacing the Ventline replacement operator with knob and screw for the Ventline Ventadome trailer roof vent with metal dome. Part number BV0115-04. .
Average Customer Rating: 4.8 out of 5 stars (130 Customer Reviews)
Replaces a lost or broken operator and knob on your Ventline Ventadome RV roof vent for motor homes and enclosed trailers. Properly sized mounting screw is included.I ordered this operator replacement for a Ventline roof vent as it was the closest one to what I needed. When it arrived, I soon found out it was not the one designed for my window, as the bracket was narrower than the original so the screw holes did not line up. If I used one or the other of the screw holes, the shaft did not line up with the hole in the screen. I lined up the operator so that the shaft was in line with the screen hole and drilled a hole where I needed it. The other hole then lined up with the large gap that the operator arm went through. I used a screw, nut and washer to go through this hole and was able to finish the job successfully. The screw to hold the knob on the mechanism was missing as it was supposed to be included. The packaging looked as if it had been re-wrapped and I suspect another customer had returned it to etrailer, sans the screw. I just used the screw from the defective operator I was returning. So now I have an operational unit, but not without having to "make do" with what I received. My original operator had a crank, but all that was available was the type with the knob, and I actually like that better. I believe that the distance between the screw holes should be included in the description to help future customers. Other than that, the folks at etrailer have been very helpful and the prices are reasonable. 86567
935660
Great product..mounting holes didn’t line up with the original crank though..just drilled 2 new holes and works like new again 920926
Perfect fit fast shipping 919547
Jane was very helpful and knew what I need even with my Garbled description. I received the product and it was just what I needed! I rate the service and the product Exceptional 912212
It was a exact replacement and works pe rfectly 912037
Bolts right in no problem and now works like new. 903792
Exact replacement for an old vent that saves time and money unnecessarily replacing whole thing. My trailer is already bedded down for a long winters nap. We just received 10", melted and now are getting 10 to 16 inches-unusual for Billings MT. 903405
Amazingly fast shipping! Ordered on the 21st and it arrived on the 23rd. The part is a perfect fit as a replacement for my older version Ventline Vent, old style, rounded dome. The part came with easy to understand installation instructions. 903075
A little different than what I had but it does the job just as well. 881359
Awesome service! My oven was up an running because of the fast delivery of the part needed. 871202
Just what we wanted. As always etrailer comes through with everything we need!! Thank you 857833
Problem: had to grind down the rivet on the slide ball so to fit in the slot in the rail. Not a big deal. Product is well made, works as expected. 852790
Yeah everything worked great, easy too look up also 849243
Part fit perfectly 844673
Works like a charm. Only issue is had was screw holes did not match the holes left from the factory removed crank from my 2004 fleet wood wilderness camper vent crank. Was able to modify like a man does and works. 844187
All the parts I bought fit my 2006 Pace motorcycle trailer with the Ventline roof vent. The vent assembly works fine now. The metal ventadome cover should work better here in Florida!! 790172
Needed to replace vents on older trailer. Fair price. 783006
Worked great, it fitted perfectly . . . and a great company to deal with , I will be ordering from you folks again 778029
Was not an exact match to what I was replacing but I made it work. 746917
good product,reasonable prices,fast shi pping 737532
Worked exactly as described. Exact fit. Great delivery time. 728128
Needed vent covers after hurricane. This was the only place these older style could be found. Easy order and quick shipment. Plus a primer on replacement included. Great help . 724544
works well, tight fit, had to file the rivet a little to install through slot on dome 714060
Quality replacement at a great price. Installed in a couple of minutes and works like new. 707828
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.