Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Customers prefer these similar products
Clamp these spring-loaded pins around your landing gear so that you can quickly and easily adjust the drop legs. Heavy-duty steel is zinc plated for corrosion resistance. Works with square jacks up to 2-1/4" wide.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello, everybody, this is Jeff at etrailer.com. Today, we're gonna take a look at the Ultra-Fab 7/16 inch diameter spring loaded quick pins for the landing gear drop legs, this is for a quantity of two pins. Now, these are spring-loaded quick pins, which will make adjusting the drop legs on your landing gear a snap, and just to show you what we're talking about, I'm gonna pop up an insert, and there's an example of a landing gear, and at the very bottom of the landing gear it has the adjustment leg that you can slide up or down to get the correct height. So basically, what these do, these are a simple installation, if you noticed, they'll clamp around the jack leg with the hardware right here. And then what you'll do is you just pull this spring loaded T-handle out, and that releases the pin, and then you can slide that adjustment leg up or down on your landing gear. Once you get it in the right position, line the hole up, let this release this spring-loaded pin, and it'll slide and lock it in place and holds it and secures it.
There's no more losing any pins like when it usually comes with just a snap pin that you have to pop out and then put it back in, sometimes that pin you might misplace it or gets lost. With these, they'll be bolted around the jack leg, so all you have to do is pull it to release it, adjust it, let it go, and it locks it into place. Now, these are a sturdy steel construction. As you can see, they are zinc plated for durability and corrosion resistance. The application, these are designed to fit landing gear with up to a 2 1/4 inch wide legs.
In other words, this measurement here, it'll fit around a 2 1/4 inch wide leg. The pin diameter right here that goes through the adjustment hole on the leg, 7/16 of an inch, and it is for a quantity of two pins. But that should do it for the review on these Ultra-Fab 7/16 inch diameter spring-loaded quick pins for the landing gear drop legs.
Average Customer Rating: 4.4 out of 5 stars (22 Customer Reviews)
Clamp these spring-loaded pins around your landing gear so that you can quickly and easily adjust the drop legs. Heavy-duty steel is zinc plated for corrosion resistance. Works with square jacks up to 2-1/4" wide.Does not fit the "Bulldog" fifth wheel landing jacks. This is not etrailers fault.
Work as advertised. Easy to install, and they make it easier to adjust the landing gear when setting up my fifth wheel.
This is a great product. We are using them on a utility trailer on which we added rear jacks. Great time saver. The internal springs could be a little stronger.
Other than that, very good product.
These look great. A lot heavier than my old ones. I put the Ultra Fab jacks on my trailer and was planning on using my old pins on the new jacks. They wouldn't fit too small. So I ordered the ones and I'm glad I did. I think I'm going to be very happy with these. Thanks guys.
VERY SATISFIED WITH THE ULTRA FAB QUICK PINS FOR MY LANDING GEAR LEGS
Installed these on my camper and they work super!!! Easy to install while the camper is supported by being attached to your vehicle.
fits ultra fab landing gear.works easily with one hand.get close and pin pop's in.
Yes the products are excellent, and are performing as expected, and would purchase again from etrailer if I need additiona items.
thanks you trailer for replacing my first order which I screwed up by ordering the wrong part very fast service
The kit was good quality with smooth operation an will worth the money its going to make setting up so much easier next season
Shipping as always fast will bug again from them
Works great. Go easy on the retainer nuts/bolts as they are not super strong when using impact tools.
Lot better than the pins that come with the landing gear. Well worth it
Easy install.Took about 15 mins to replace my old pins.
Jason
3/18/2019
Still working great!!
Second order fast delivery and I will buy from e-trailer again
Great product at a reasonable price . Add in fast shipping and eTrailer scores again. Very pleased with my purchase...Using our trailer has been greatly simplified because of these pins..
Great works just as advertised with my new landing gear.
A pleasure doing business with you folks.
Fast delivery
Great product
Easy to install / Works Great
SERVICE WAS EXCELLENT. MUCH TO MY REGRET THE PRODUCT ORDERED DID NOT WORK BUT I WILL CONTINUE TO USE THIS WEB SITE FOR ANY FUTURE NEEDS.
Just received the product and will install later. Seems to be well made. Shipping was quick and on time.
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jim S.
9/30/2016
Still working fine after a year, no problems with them.