Solenoid Shield for Titan Model 60 Trailer Brake Actuators - Zinc

Ask the Experts about this Titan Accessories and Parts

• Disc Brake Master Cylinder for a Titan Model 10 Actuator
  To convert your Titan model 10 actuator to work with disc brakes you will have to change out the master cylinder with # T4747100. The solenoid is something else entirely. The replacement master cylinder will fit directly in place of the existing master cylinder.
  view full answer...
• Orientation of Roller Assemblies when Reassembling Titan Model 60 Brake Actuator
  When assembling the roller assembly, the rollers should be installed so that the beveled edges face the outside of the tongue, away from the shock absorber. I have confirmed this with my contact in the Technical Services department at Titan.
  view full answer...
• Parts Needed to Repair Brake Line Connection on Titan Model 60 Hydraulic Trailer Coupler
  It looks like that is a piece of flexible brake line you are using. You would need standard flexible brake line with a 3/8 inch male fitting. We offer them in varying lengths. A 13 inch long brake line with fittings (male on one end, female on the other) is available as part # T0777300, 18-25/32 inch length as part # T0776500 or a 25 inch long line is available as part # T0980100. If you do not already have one installed, I would recommend a solenoid shield, part # T4835800183 to...
  view full answer...
• Replacement Master Cylinder and Backup Solenoid for Titan Model 60 Trailer Brake Actuators
  Since the fitting broke off, there could be other damage to the master cylinder, so I would recommend that if you keep your Model 60 Actuator, replace the master cylinder with # T4820000 for disc brakes or # T4395100 for drum brakes. The Replacement Solenoid Valve for Titan Brake Actuators, is # T4748800. It fits Titan Model 6, Model 60, Aero 7500, Model 10, and Model 20 actuators. I could not find any information on a Model 66.
  view full answer...
• Should Titan Model 60 Actuator be Replaced if Theres Left to Right Play on Inner Section
  If you are getting a lot of left and right play in your Titan Model 60 actuator that would indicate it's internally damaged or it has a very high amount of wear and either way needs to be replaced. For an exact replacement we have the part # T47154107K which is for disc brakes or the # T43329007K for a drum application.
  view full answer...
• Recommended Replacement Brake Actuating Surge Coupler for Atwood 85778
  Thanks for the photo. That is a great help for getting you the correct replacement. I recommend the Demco Hydraulic Trailer Brake Actuator - Drum Brakes - Zinc Plated - 2" Ball - 6,000 lbs # 8605001 for a nickel plated option. This coupler does not have the reverse lockout, so you will need to add it using the Replacement Solenoid Valve for Titan Brake Actuators with Reverse Lockouts # T4748800 and the shield # T4835800183. We don't have any Atwood replacement master cylinders...
  view full answer...
• Comparing Demco and Titan Disc Brake Actuators with Electric Lockouts
  That is a tough question to answer as both are excellent manufacturers with their respective pros/cons. In regards to brake actuators, they both make and manufacture them here in the U.S.A. and they both come with a one year warranty. In regards to differences, Demco makes a wide range of different trailer and towing products whereas Titan specializes more in trailer brakes. WIth that being said we have had more positive feedback from Titan products in regards to trailer brakes, actuator...
  view full answer...
• Adding Electric Lockout and 5-Way to Trailer with Titan Model 60 Actuator
  To add an electric lockout to your Titan Model 60 actuator only requires the part # T4748800 and then if you wanted to add a shroud to protect the lock out you'd also need the part # T4835800183. To activate the electric lock out you need a reverse light circuit carried to it. Typically a 5-way is needed for this to carry the extra circuit. For a 5-way you'd then want the part # W002290 which you can replace your 4-way with. For a 7-way to a 5-way adapter then you'd want the part #...
  view full answer...
• Using Front Hitch To Move Trailer With Hydraulic Surge Brakes
  If you have a manual lockout, you will be able to use that and navigate with your front hitch without any wiring. If you have an electric lockout, you will need to supply 12 volts to that solenoid to release the brakes. I'd suggest getting a matching connector for your trailer like # PK11893 or # HM47900 and hardwiring the reverse wire directly to your battery and run a ground wire to the negative battery terminal from the connector. This will allow you to have that single function to...
  view full answer...
• Can a Reverse Lockout Solenoid Be Added to an Actuator That Does Not Have a Lockout Solenoid
  Yes, you can add a solenoid valve to your brake actuator on your trailer to prevent the brakes from locking up when in reverse as long as you have the standard 3/16 inch brake lines on your trailer. You will need a Replacement Solenoid Valve # T4748800. This valve will attach between the master cylinder and your brake line and it will wire into the reverse light circuit on your trailer. Once your vehicle is put in reverse the solenoid valve closes and prevents pressure from reaching...
  view full answer...
• Backing Up Trailer When Using Titan Model 60 Hydraulic Surge Disc Brake Actuator # T4819900
  The Titan Model 60 Hydraulic Surge Disc Brake Actuator, part # T4819900, does not include a lockout function for backing up the trailer. Couplers are available with either electric or manual lockout, or no lockout. This particular Titan coupler does not offer this function. If you wish you can install additional components to provide this function in your coupler. You will need Titan Solenoid Valve, part # T4748800, and Titan Solenoid Shield, part # T4835800183. The fitting that...
  view full answer...
• Is a Reverse Electric Lockout Needed on a Boat Trailer with Titan Model 60 Actuator
  The issue is that with the way a surge coupler works when backing up, normally up hill, the trailer is pushing the other way which will cause the actuator to compress in sending fluid back to engage the brakes. This makes it very difficult or impossible sometimes to back the trailer up. There are 2 kinds of lock outs to prevent this, a manual which is built into an actuator and prevents the coupler from pushing in, and there is the electric type. It will energize when the vehicle is...
  view full answer...
• How to Wire Titan # T4748800 Reverse Lock-Out Solenoid Valve
  The Titan Replacement Reverse Lockout Solenoid you mentioned is extremely easy to wire. The solenoid has two wires exiting it. One wire grounds to the trailer tongue, the other would connect to the reverse light circuit on the tow vehicle. Once wired, the solenoid will close when the tow vehicle is shifted into reverse, preventing the trailer brakes from applying when the trailer is backed. Since it sounds like both your vehicle and trailer have a 4-pole connector, you'll need to install...
  view full answer...
• Titan Surge Brake Actuating Coupler to Replace Atwood Coupler
  The Titan Zinc-Plated Brake Actuator - Drum - Multi-Fit Ball - Bolt On - with Lockout - 7K # T4339720 is a great option for the Atwood coupler replacement. This includes the electric lockout solenoid. The brake line fittings will be the same. The Titan Zinc-Plated, Leverlock Brake Actuator # T43329007K is also a great replacement option, and you can add the Replacement Solenoid Valve for Titan Brake Actuators with Reverse Lockouts # T4748800. I recommend also getting the Solenoid...
  view full answer...
• Need Adapter to Connect Titan Model 10 Master Cylinder to Reverse Lockout Solenoid
  The reverse lockout solenoid you recently purchased, part # T4748800, is intended for use in a number of actuators from Titan and Dico, including newer production of the Titan Model 10 Drum Brake Actuator. In these applications the valve, with its 1/8-27 fine pipe threads, should be a direct fit. Please note that it is necessary to remove the orifice connector (part # T1209800) from the back of the Model 10 actuator before installing the reverse lockout solenoid. If your Model 10...
  view full answer...
• Titan Model 60 Drum Brake Actuator with Electric Lockout
  The Titan model 60 drum brake actuator # T4339720 does feature an electric lockout and the multi-fit type ball coupler rather than a lever lock style. You can simply add an electric lockout to the existing coupler. This will save you time and money. My contact at Titan confirmed this is a good way to go. You can use parts # T4748800 and # T4835800183.
  view full answer...
• Can a Reverse Lockout Solenoid Be Added to an Actuator That Does Not Have a Lockout Solenoid
  Yes, you can add a solenoid valve to your brake actuator on your trailer to prevent the brakes from locking up when in reverse as long as you have the standard 3/16 inch brake lines on your trailer. This valve will attach between the master cylinder and your brake line and it will wire into the reverse light circuit on your trailer. Once your vehicle is put in reverse the solenoid valve closes and prevents pressure from reaching the brakes. Make sure that when you are backing up...
  view full answer...
• Titan 60 Lever Type Latch With Electric Reverse Lockout for Drum Brakes Recommendation
  Yes, check out the Titan Actuator part # T43329007K . This is a drum brake, model 60 actuator with a 6k capacity, and has a leverlock latch system. All that is missing is an electric lockout solenoid which can be purchased separately, part # T4748800. We have learned that in order to attach this solenoid to the master cylinder, the fitting that is currently on the master cylinder will need to be removed and the solenoid threaded directly on in its place. You will also probably want to...
  view full answer...
• Does Drum Brake Master Cylinder Need to be Replaced with Atwood Master Cylinder for Disc Brakes
  I spoke with the Titan, who confirmed that the master cylinder # T4820000 is indeed the correct replacement when switching from drum to disc brakes. Because hydraulic disc brakes operate at a higher pressure (1,500 psi) than drum brakes (1,000 psi), the master cylinder used for your current drum brakes won't deliver the required pressure to effectively actuate disc brakes. If your current Titan Model 60 doesn't have the electric lock-out feature that defeats the brakes when the vehicle's...
  view full answer...
• Troubleshooting Surge Brakes Locking up When in Reverse
  With surge brakes, you have a brake actuator applying the needed pressure to the brakes but to be able to back up you will need to have a manual lockout or an electric lockout solenoid, like # T4748800, which will close when you shift the vehicle into reverse, allowing the trailer to be backed up. You may also need a solenoid cover like the Titan # T4835800183, depending on what brake actuator you currently have. Typically surge brakes are found on boat trailers, and commonly the...
  view full answer...
• Parts Needed to Backup Without Putting on the Surge Brakes When Parking or Launching a Boat Trailer
  Yes, there is a way to back up your boat trailer and keep the surge brake actuator, # T43329007K, from applying pressure to the trailer brakes. You will need an electric lockout solenoid, # T4748800, which will close when you shift the vehicle into reverse, allowing the trailer to be backed. Along with the solenoid, you will need a solenoid cover, # T4835800183, if your actuator is the model 60 actuator that you referenced. The cover will keep the solenoid from getting stepped on and...
  view full answer...
• Troubleshooting Trailer Ball Fit and Backing up with the Titan Model 60 for Disc Brakes # T43329007K
  The Titan Zinc-Plated Lever Lock Actuator # T43329007K that you referenced is adjustable and will fit trailer balls that are 1-7/8 inches, 2 inches, and 50 mm. In order to fit the coupler to the specific size of trailer ball that you have, some small adjustments can be made to optimize the fit. If you are using the Titan Level Lock Brake Actuator # T43329007K, with different size trailer balls to tow your trailer adjustments will have to be made each time a different size trailer ball...
  view full answer...
• How To Stop Brakes On Trailer From Locking When In Reverse Using Titan Model 10 Brake Actuator
  What you will need to do is install the Replacement Solenoid Valve, part # T4748800. The Titan Replacement Solenoid Valve # T4748800 will stop the brakes from activating when you are in reverse. You may also be interested in the Titan Solenoid Shield, part # T4835800183, which will protect the solenoid valve from being stepped on if you do not already have a cover.
  view full answer...
• 7,000 lb Hyudraulic Actuator for Drum Trailer Brakes with Trailer Brake Lock Out for Backing Up
  The Titan Leverlock Brake Actuator, # T43329007K, that you referenced does not include a lockout system for backing your trailer, but an electric lockout solenoid, # T4748800, can be added to allow you to back the trailer. At this time we do not have a 7,000 lb coupler with a reverse lockout factory installed. Along with the solenoid you will need a shield, # T4835800183, to protect the solenoid from damage, and you will need to upgrade the 4-Way connector on your truck and trailer to...
  view full answer...
• Why Does Boat Trailer Lock Up Brakes when Backing Up
  Sounds like you have a boat trailer that you tow your Triton 21RX with that has surge brakes that are locking up in reverse. This is a fairly common scenario that has an easy fix. With surge brakes, you have a brake actuator applying the needed pressure to the brakes but to be able to back up you will need to have a manual lockout or an electric lockout solenoid, like # T4748800, which will close when you shift the vehicle into reverse, allowing the trailer to be backed up. You may...
  view full answer...
• Replacement Titan Master Cylinder and Backup Solenoid Needed For My Titan Model 60 Actuator
  For a replacement master cylinder you will need the Titan Replacement Master Cylinder, part # T4395100, to use with your Titan Model 60 Actuator. Then, you will want to use the Titan Replacement Solenoid Valve, part # T4748800. This Titan Replacement Solenoid Valve # T4748800 will stop the brakes from activating when you are in reverse. You may also be interested in the Titan Solenoid Shield, part # T4835800183, which will protect the coupler from being stepped on if you do not already...
  view full answer...
• Do I Need To Install A Brake Controller To Activate Or Deactivate Surge Trailer Brakes In Reverse?
  Great question. Let me cover brake activation first. If you wish to have active braking on a hydraulic system when backing up, you would need to have Electric over Hydraulic brakes and not a surge brake coupler. Surge brake couplers do not allow active braking when in reverse. To add the electric over hydraulic system, it will require a brake controller like # 39523 and an electric over hydraulic brake actuator like the HydraStar Vented Marine Electric Over Hydraulic Actuator for Disc...
  view full answer...
• Can Replacement Solenoid Valve, # T4748800 be Used on a Titan Model 60 Trailer Brake Actuator
  Yes, the Replacement Solenoid Valve, # T4748800, will fit the Model 60 Titan Actuator. We have learned that in order to attach this solenoid to the master cylinder, the fitting that is currently on the master cylinder will need to be removed and the solenoid threaded directly on in its place. You will also probably want to keep the solenoid covered. Actuators that come with the electric lock out already have a cover in place. But, you can add it on with part # T4835800183.
  view full answer...
• Reverse Lock Out Solenoid Recommendation for Titan Leverlock Brake Actuator, # T43329007K
  The Titan Leverlock Brake Actuator, # T43329007K, that you referenced does not include a lockout system for backing your trailer, but an electric lockout solenoid, # T4748800, can be added to allow you to back the trailer. At this time we do not have a 7,000 lb coupler with a reverse lockout factory installed. Along with the solenoid you may also want a shield, # T4835800183 which will help keep the solenoid undamaged.
  view full answer...
• Can Titan Leverlock Brake Actuating Coupler # T47154007K Be Submerged
  The Titan Leverlock Brake Actuating Coupler can be submerged for brief periods and would be an outstanding choice for boat trailers with hydraulic disc brake systems. For drum brakes, you'd want to use part # T43329007K. Because neither of these couplers have a reverse lock-out feature, you'll want to use free backing brake assemblies which will allow you to back the trailer without having the brakes apply. Or, you could use the reverse lockout solenoid, part # T4748800 which would release...
  view full answer...

Do you have a question about this Accessories and Part?