Replacement 3-Wing, Low M6 Hand Knob for Thule Roof Mounted Carriers

Ask the Experts about this Thule Accessories and Parts

• How to Lock the Thule 593 Wheel-On Bike Wheel Carrier to a Roof Rack
  The easiest way to lock a wheel and the # TH593 to a cross bar would be to use a cable lock like the part # 8291DPS. This is a pretty short cable lock at 3 feet that also has a no-scratch sleeve on it to protect the paint on the roof of your vehicle.
  view full answer...
• What are the Dimensions of Replacement 3-Wing, Low M6 Hand Knob 753-0783
  I went out to the warehouse to measure Thule replacement 3-wing knob, # 753-0783. At its widest point it is 1.34 inches and from the end of one wing to the space in between the other 2 wings it is 1.10 inches. And it is 0.70 inches tall.
  view full answer...
• Replacement Knob for a Thule Hull-A-Port Kayak Carrier
  Yes, I checked with Thule and replacement 3-wing knob, # 753-0783, does fit the Thule Hull-A-Port, # TH834.
  view full answer...
• Is the Replacement 3-Wing, Low M6 Hand Knob # 753-0783 a Direct Replacement for Thule Carriers
  I went out to the warehouse and pulled the Replacement 3-Wing, Low M6 Hand Knob for Thule Roof Mounted Carriers # 753-0783 and compared it with the hand knobs on the Thule Hull-A-Port Kayak Carrier # TH834 and they were the same part. If the hardware that you received was just like the original hardware then this hand knob will work just like the original one would have. If you were pleased with the hand knobs that came with your equipment then you will be happy with part # 753-0783...
  view full answer...
• Availability of Thule 3-Wing, Low M6 Hand Knob
  Sounds like you are looking for the part # 753-0783. This knob is the Thule 3-Wing, Low M6 Hand Knob for Thule Roof Mounted Carriers that you said you are looking for.
  view full answer...
• Is the Threaded Portion of the Replacement 3-Wing Hand Knob part # 753-0783 Metal or Plastic
  The threaded portion of the Replacement 3-Wing Hand Knob part # 753-0783 that you referenced is metal.
  view full answer...
• Replacement Mounting Hardware for Thule Hull-a-Port Kayak Carrier
  I understand your concern about your Thule Hull-A-Port Kayak Carrier # TH834 coming loose from your vehicle roof rack crossbars but I cannot recommend using any alternate hardware (such as that from another Thule carrier). What I suggest you do is apply a thread lock compound like Loctite # LT37643 to the hardware's threads. This should prevent the knobs from coming loose on their own but still allow you to remove the carrier if you wish. If you still have an issue then I suggest...
  view full answer...
• Thule Sidearm Parts for Compatibility with Subaru Factory Roof Rack
  For your 2010 Subaru factory crossbar, you can upgrade your Sidearm Mounting hardware to fit that rear rail. The front rail should work with the current hardware, but the upgraded hardware should work with both bars if that is what you are mentioning. Unfortunately even the newer model of the Sidearm you are referring to is discontinued so the other parts are not available. If the rear hardware works for the front even though it is long, it may be the best option. You will need two...
  view full answer...
• Wing Knob for Use with Thule Replacement U-Bolt TH02943
  For use with Replacement U-Bolt # TH02943 you can use M6 Wing Hand Knob # 753-0783.
  view full answer...
• Hardware for Fairing Clamps on Thule Canyon Rooftop Basket
  I checked with Thule and the hardware is available to install the Replacement Fairing Clamp for Thule Canyon Roof Baskets # 1500052562. What you need is Carriage Bolt # 915-0622-54; if you also need the 3-Wing Hand Knob that is part # 753-0783.
  view full answer...
• Building a Replacement Foot for a Thule Sidearm
  The washer plate, part # 853-0333-02 is used to position the front mount along the track of the Thule Sidearm, and you're right, it is missing from the question you were looking at. To fully rebuild the assembly, the correct parts list is: 2 Washer Plates, part # 853-0333-02 2 Wing Nuts, part # 753-0783 2 Carriage Bolts, part # 915-068-054 1 Levelling Gasket, part # 853-7442 1 Metal Bracket, part # 853-5513 1 Clamp Bracket, part # 853-7441 You need to do this for both crossbars...
  view full answer...
• Replacement Hardware for Old Thule Hull-A-Port Kayak Carrier
  The Replacement Carriage Bolt M6 x 65 # 915-066-554 are 65 mm in length which is 2.559 inches so these are the length you need. You may also want the Replacement Metal Bracket for Thule Roof Mounted Carriers # 853-5513 and the Replacement 3-Wing, Low M6 Hand Knob for Thule Roof Mounted Carriers # 753-0783.
  view full answer...
• Which Bolt is Compatible with the Thule 3 Wing Knob # 753-0745
  The threads on the Replacement Square Head Bolt for Thule Fairings, # 853-208909, are an M6 bolt. I pulled the bolt and another M6 item, wing nut # 753-0783, and tested them together. The bolt threaded in the nut correctly so it is an M6 bolt and knob. Knob # 753-0745, also accepts an M6 bolt. I cannot guarantee that the bolt will work with anything other than a Thule product. The bolt head is about 3/4 inches square and the head is 1/8 inch thick. Overall, the length of the bolt is...
  view full answer...
• Will Kuat Trio Roof-Mount Bike Rack Fit Subaru Factory Roof Rack Crossbars
  Its easy to check the fit of the Kuat Trio roof-mount bike carrier on your Subaru's factory crossbars. Just measure their width and height. As long as the bars are not larger than 3-1/2-wide x 1-11/16-inches tall then the Trio # TR02 will fit fine. This rack can handle up to a 45-lb bike with tires up to 4-inches wide. Since the Trio bike rack is a fork-mount type that requires you to remove the front wheel you might consider a tire carrier to store that tire on the roof. We offer...
  view full answer...
• What Are the Dimensions of Thule Replacement U-Bolt, # TH02943
  I went out to the warehouse and measured a Replacement U-Bolt, # TH02943. The center to center distance between each end of the u-bolt is 4 inches. It is 2 inches deep in the center. The cross bars on your Volvo XC90 would have to be smaller than those dimensions in order for these u-bolts to fit. The Car-Go cargo box is not made anymore so I cannot test this u-bolt with the knobs it used. But I can tell you that this u-bolt uses an M6 (6mm) knob like # 753-0783.
  view full answer...
• Thule Replacement Parts for Securing Tram TH9033 Ski Rack To Bike Rack Upright
  The three parts you are looking for are the metal bracket # 853-5513, cap screw # 919611054, and replacement wing nut # 753-0783. These are the three parts that attach the portion of the Tram # TH9033 that you pointed out in your picture to the upright of the bike rack.
  view full answer...
• Will Yakima Aero Crossbar SmarT-Slot Kit Bolts # Y03098 Fit Thule M6 Wing Nut
  I actually went out to our warehouse to test a bolt from the Yakima Aero Crossbar SmarT-Slot Kit # Y03098 with an M6 wing nut from Thule (part # 753-0783). The Yakima bolt threaded into the nut perfectly which means it is indeed an M6 bolt. They will work just fine with a Thule M6 wing nut like what you have.
  view full answer...
• T-Bolt Recommendation for Use with M6 Thule Knob
  Since I can't recommend one way or the other whether or not your wooden cargo box would be safe on the top of your vehicle travelling at highway speeds all I can tell you is that the M6 knob part # 753-0783 that you referenced would require an M6 T-bolt like part # 853-6511-02 for a 64 mm bolt or part # 853-6511 for 92 mm. Please be very cautious with your roof box setup. I would imagine a wooden cargo box would be pretty heavy. If you wanted to go with a lighter option I would strongly...
  view full answer...
• Replacement 3-Wing M6 Knob for a Thule Hull-A-Port Pro Kayak Carrier
  We have the exact knob you are looking for. It is # 753-0783. This same knob is used on several Thule carriers including your Hull-A-Port Pro kayak carrier.
  view full answer...
• Replacement Wing Knob for SportRack SkyLine XL Roof Mount Cargo Box
  For an exact replacement knob for your SportRack SkyLine XL Cargo Box # SR7095, you will want to use part # TH04877. I confirmed with my contact at Thule/SportRack that this is the knob that originally came with the cargo box. The # 753-0783 knob that you referenced will fit the M6 bolt that came in the SkyLine, but the knob is shorter than the # TH04877. The # 753-0783 knob is designed to fit Thule roof-mounted watersport carriers.
  view full answer...
• What is the Thread Pattern and Size of Replacement Square Head Bolt for Thule Fairings
  Yes, the threads on the Replacement Square Head Bolt for Thule Fairings, # 853-208909, is an M6 bolt. I pulled the bolt and another M6 item, wing nut # 753-0783, and tested them together. The bolt threaded in the nut correctly so it is an M6 bolt. I cannot guarantee that the bolt will work with anything other than a Thule product. The bolt head is about 3/4 inches square and the head is 1/8 inch thick. Overall, the length of the bolt is about 1-1/8 inches.
  view full answer...
• What Thule Knob Will fit the T-Bolts of the Xadapt2
  The bolts of the # Xadapt2 that you mentioned are M6. For a low profile Thule M6 knob we have the part # 753-0783.
  view full answer...
• Replacement Hardware To Attach Wind Fairing on Thule Canyon XT Roof Cargo Basket
  In order to attach the wind faring to the Thule Canyon XT Roof Cargo Basket part # TH859XT you will need the Replacement Fairing Clamp part # 1500052562 (Qty. 5), the Replacement M6 x 22 Carriage Bolt part # 915-0622-54 (Qty. 5), and the Replacement 3-Wing Hand Knob part # 753-0783 (Qty. 5). Please note, you will also need 1/4" Flat Washer (Qty. 5) which can be obtained at any local hardware store.
  view full answer...
• Adapter Needed for Thule J-Style Kayak Carrier on Rola Roof Rack System for 2012 VW GTI
  If the bolts on your Thule J-Style kayak carriers aren't long enough then you most likely need the adapter kit # THXADAPT11 which is required when installing the Thule Hull-A-Port # TH834 on the Thule AeroBlade crossbars. Since the crossbars on your Rola Sport Series Roof Rack with GTX Mounting System # 59736 has a similar shape, you should be able to use the adapter just fine. If you have other J-Style racks that we carry just let me know what they are and I can see if we have similar...
  view full answer...
• How To Use Yakima HullyRollers On Thule Aero Crossbars
  I do have an option for you to use the Yakima HullyRollers 8004015 on a Thule WingBar Evo Crossbar like part # TH711420 but there isn't any option to mount them within the channels. The only mounting option available for the HullyRollers are wraparound clamps. The correct wraparound clamps for aero crossbars are the Universal MightyMounts for Yakima Roof Mounted Accessories part # Y03590. The Replacement 3-Wing, Low M6 Hand Knob part # 753-0783 is made of plastic and there is no metal...
  view full answer...
• Replacement 3-Wing Knobs for Thule Sidearm Roof Bike Carrier
  Thule Replacement Knob part # 753-0745 is the correct knob for the Sidearm rack's ratcheting arm. It fits both versions of this rack. For the knob that secures the carrier to the roof rack crossbar use M6 part # 753-0783.
  view full answer...
• Wing Nuts for Use With the XSporter Load Bar Adapter Kit for the Thule Hull-a-Port Kayak Carrier
  The bolts in part # THXADAPT3 are M6 sized, and work with the M6 Wing Nuts, part # 753-0783 However, If you have the Hull-A-Port Pro then part # THXADAPT3 will simply replace your existing bolts, no problem. If you have the Hull-A-Port Pro, part # TH835PRO, you'll need part # THXADAPT11.
  view full answer...
• Knob Recommendation that Fits Carriage Bolt 915-0640-11
  If you wanted a 3 wing knob that would fit the carriage bolt part # 915-0640-11 that you referenced you would actually want the part # 753-0783 which is an M6 sized knob to match the bolt. The other knob you referenced would be to big as it is a M8.
  view full answer...

Do you have a question about this Accessories and Part?