This 4-1/2" vacuum cup lets you mount or hang a variety of objects to non-porous surfaces with no tools required. A pump-action vacuum creates 120 pounds of pull strength without drilling holes or damaging the surface it's attached to.
Features:
Specs:
This 4-1/2" vacuum cup lets you mount a variety of objects to most horizontal or vertical, non-porous surfaces without drilling any holes. It uses a pump-action vacuum to create 120 pounds of pull strength without damaging the surface it's attached to. All metal parts are constructed with durable, high-grade stainless steel.
It has 2 slotted holes in the top that allow you to bolt nearly anything to the back of the cup. It also has a threaded 1/4 - 20 stainless steel insert in the center for attaching other SeaSucker products.
This vacuum cup holder is quick and easy to mount. To install the vacuum cup make sure the mounting surface is clean and place the cup on your vehicle or wall then press the pump several times until the orange band disappears. To break the seal and remove the holder simply pull the T-shaped tab up and towards the center of the cup. As suction decreases over time the plunger will extend from the cup. When the orange indicator band shows simply re-pump the plunger.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello everybody, this is Jeff at etrailer.com. Today we're gonna take a look at the SeaSucker four and a half inch diameter black vacuum mount. Now this four and a half inch diameter vacuum cup, this'll let you mount or hang a variety of objects to your non-porous, either horizontal or vertical surfaces, and there's no tools required. Basically, you can attach this or remove it in seconds, uses this pump action vacuum here, which creates a nice 120 pounds of pull strain without drilling any holes or damaging the surface that you're gonna attach it to. And just to demonstrate that, I wanted to show you. Now, I have a non-porous material right here.
The table itself is porous, so it wouldn't work on that. So I have this piece of porous or non-porous material just to demonstrate this on. So basically what you'll do is just put this onto the surface, and again, it can be horizontal like this, or vertical. Basically just put a little pressure down on this and then just start pumping the plunger. And as you're pumping that plunger, you'll notice that orange stripe that's on the plunger slowly disappears.
Once you pump it enough, that orange is gone and it's given you the strength you need 120 pounds, we mentioned, of pull strength and it's attached. And again, it'll even work vertically. And then to remove it, it's very simple, on both sides, you have one here and one here, a little tab, you just pull up on that tab and it releases it. So it makes it very easy to attach and you will move it very quickly. If you notice on the top, it has these slotted holes.
This will let you hang or bolt of variety of objects to it. And in the very middle, there's an actual half inch by 20 size stainless steel insert that'll let you attach other SeaSucker products to this unit. It is a nice hard plastic construction, very lightweight, yet durable. If you notice, they do include this nice protective cap that'll protect the vacuum cup from hardening or cracking. Just basically when you're not using it, just go ahead and put this all the way around on it.
Push it down in there. And once you get it all the way in there, you can see that you can store it and not have to worry about damaging that rubber portion of the vacuum cup. So we mentioned it is a black color, it is made in the USA. Again, the pull strength on this is 120 pounds. The diameter, we take our cap off, and we'll put a ruler on it just to show you, is gonna be right at four and a half inches. And the weight on this part is only about a half a pound. But that should do it for the review on this Sea Sucker four and a half inch diameter black vacuum mount.
Average Customer Rating: 5.0 out of 5 stars (3 Customer Reviews)
This 4-1/2" vacuum cup lets you mount or hang a variety of objects to non-porous surfaces with no tools required. A pump-action vacuum creates 120 pounds of pull strength without drilling holes or damaging the surface it's attached to.Works great. For a rest when hunting
These work great for about 1 month before they need a little pump up to stay strong
Item shipped next day and arrived the following day. Thanks!
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.