Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hey everybody, Ryan here at "etrailer". Today, we're gonna be taking a look at and showing you how to install the line of pollak type one circuit breakers. A circuit breaker is a really small but important component. Like the one that we have here today. And what that circuit breaker is gonna do is protect whatever you're powering up. Whether it be a fan, a winch, a pump, a motor.
In our case today, we have this for a trolling motor on a fishing boat. It's going to protect those accessories. That way if a short or something like that we're to happen, they're not going to destroy that accessory. So the way the circuit breaker is going to work is almost like a fuse. To kind of keep things simple.
There's actually a contact inside of the breaker that allows power from one side of the breaker to the other. Well, whenever electricity is running through that contact, it's going to generate heat. And depending on what size breaker you have, whenever it detects too much of that heat, it's going to lift that contact up or break the connection if you will. That way, power can no longer go from your battery or your power source to the auxiliary product that you're powering up. So you no longer gonna have that connection.
And that's going to protect that said accessory. Now these are auto resetting. So what that means is once that contact cools down enough, it's going to make the connection again. And power will once again flow through. These breakers are designed to work with 12 volt systems.
However, if your accessory runs on a different voltage, lets just say 24 volt to give an example, you will need to get a different type of breaker. And I would just suggest one like this. This is a type three breaker. You could see they're a little bit different but the concept is the same. They're gonna work the same and keep everything protected. And because this is a type three, it's going to allow you to use up to 42 volts. So something I thought that was worth mentioning and if that's your case, you can find these breakers right here in etrailer. So there's a few different reasons why you would need a circuit breaker. One of them being, let's say you're hooking up a new accessory and you wanna make sure to keep it protected. So that's pretty straightforward there. Another reason would be sooner or later, even though these breakers are auto resetting, if they do trip a lot, sooner or later they will wear out and just not work anymore. So you could always just use it as a replacement. Or like in our case today, this is a new boat and this was the existing breaker on that trolling motor. And when you tried to remove the wires, the studs are just completely rusted. The stud actually broke off in there. You can't get the nut off of it. And personally, when it comes to stuff like this, I just wanna make sure that the electrical system is right. And I don't want any trouble. Be stranded out in the water or anything like that. So that's why we replaced this one. It's just worn out. And by doing that, it gives you a little more peace of mind knowing that you have a brand new breaker and you have something that's reliable. Just something I wanted to point out, in our case, our breaker is mounted in this compartment here, where it's gonna remain dry and out of the elements. But if yours is mounted outside, that's just fine. The weather isn't going to damage it. Obviously after years of use and everything else will start to show somewhere. So one thing you can do, you can pick up separately a rubber cover that kind of goes over this breaker and over the contacts. So it's gonna help keep everything off of it and not to mention too, might eliminate you if it's somewhere in a high traffic area or something, for example. And you're worried about bumping into the two breakers while you have power to it or the two studs rather. It'll eliminate you from tripping the breaker that way as well. So just something I thought was worth mentioning. So now that we seen our breaker mounted up and kind of learned about how it works and what it does, let's go ahead and set a few different ones on our bench and take a closer look at them. So when it comes to the line of pollak circuit breakers, you're gonna have many different options. So here, I just laid out a few of the common ones. We have a 20 amp, a 30 amp, and a 50 amp. And as you can see they're nearly identical in size, shape, everything else. The only difference is going to be internally. So just to kind of give you a comparison there. Now there's a lot of different combinations that you could use. Here, we have our mounting bracket that runs this way. But these are also available with mounting brackets that run the opposite way. So it can have a couple of different mounting choices. Whichever best suits your needs. And there's also these breakers without any brackets at all. So if you have maybe some type of housing or something that your breakers we're originally in, there's an option available for you as well. Something I do like about these breakers is that the studs are going to be different colors. And they're also going to have a label, auxiliary and battery. So it really does take the guesswork out of it whenever you're hooking this up. You know that the copper-colored post labeled battery is gonna go to your source of power and the silver-colored one labeled auxiliary is going to go to what you have it hooked up. Whether it be a pump, a motor, winch, whatever the case may be. So it really just makes things a little bit easier. So sometimes these things have to be mounted in relatively tight spots. So I figured there's a couple of measurements that some of you may find useful. If we go from the center of the hole to the center of the hole here in the mounting bracket, that's going to measure out one and nine-sixteenth of an inch. And that measurement is gonna be the same regardless if you have the mounting bracket like this or the straight mount one. As far as the height. So from the bottom of the breaker to the top of the stud, that's going to be one and three-eighths of an inch. So relatively compact. And as long as you have a little bit of space, you should be able to get these mounted up properly. So when it comes to actually figuring out what size breaker you need as far as the amperage rating goes, there's a few different things that you can do. A lot of times, whatever product you're trying to power up will actually have a label on it telling you what size breaker that they recommend or how many amps it draws. If that information is not on there, you can always reach out to the manufacturer. And nine times out of 10, they're going to have a suggestion that they would give you. Or if all else fails, you can always use an amp meter and measure the amount of amps that product is drawing. And that can help you figure out what size breaker you need. If you ended up testing it, kind of a good rule of thumb is just to get a breaker rated a little bit higher than what it actually pulls. Not by much. And I say that because a lot of times these products, when you first turn them on, they can draw a little bit more amps right off the bat. And so you want to give that a little bit of room. You don't want to trip your breaker all the time for no reason really. So as far as choosing what size breaker you need, that's just a little bit of information you can use to help figure that out. I will say the breaker does feel pretty good. Like it's well-made. It is metal here on the housing and there's some plastic up top. But even if you try to squeeze it really hard and try to bend it or flex it, it's not moving at all. So it's nice and solid. Feel like if you bump into it or anything like that, shouldn't really have to worry you a whole lot. And I do like the fact too that they give you nuts that are actually really star washers, almost. It's like a lock nut. So that way, whenever you hook up your wiring to it and snug it down, you shouldn't have to worry too much about that backing off over time or becoming loose. But other than that, regardless of your application, these are all gonna get installed pretty much the exact same way. And it doesn't really take a whole lot of time. Not a whole lot to them. So really shouldn't give you a whole lot of issues. Speaking of which, let's go ahead and hook it up together now. So to get your breaker installed, the first thing that you're going to want to do is make sure that you have your battery or power source disconnected. So in our case, we have a battery disconnect switch here. So I'm just going to turn that into the off position. Now we won't have any power. And what I'm going to be powering up or using the circuit breaker for rather, is a trolling motor on a fishing boat. And like I said, these have tons of different applications. And this is just one of them. So here's my wires. And what I'm gonna do is take the breaker and I'm going to mount it to this wall right here. Now, whenever you mount this up, keep in mind that the copper-colored post labeled battery, goes to the power supply and the silver auxiliary post goes to whatever you're running. So mount it to what makes sense. In our case, this is my battery wire, the one that is getting power. So I'm gonna mount this with the battery post facing up. And I'm going to use some self-tapping screws to do that. And you can find these here at etrailer. If you need some. Get it lined up. What I like to do, get one going about half way. That kind of allows you to swing it where you want it to go. My grandma always self tapper. You got a whole lot of room to work with here. Get that in. Then we can just run them both down completely. So now that we have the breaker secured we can go ahead and remove these nuts. Now, when you're taking these off, be careful. A lot of times they kind of just pop right off at the end. And they're pretty easy to lose. So just be mindful of that. So once we have them off, we can take our corresponding wires. So again, this one here is coming from my power supply So I'ma put that ring terminal over the battery stud. And I do wanna mention, if you need any ring terminals or anything like that, you can pick those up right here at etrailer. We have quite a bit of wiring options and different types of ring terminals. So if you're running low on any of that stuff, you can always grab it here. And then I'm gonna take my other ring terminal. This goes up to the trolling motor itself. So I'll put that over the auxiliary post. Let's go ahead and get these started hand tight. We can come back with a three-eighths socket and just tighten tighten the nuts down. Whenever you're tightening these, you don't have to really crank on them by any means. You just want to get them snug. Then I usually go kind of more, maybe another eighth of a turn. Something like that. So once you get everything on tight. So once you have everything tight and you're done working on all your electrical components, we can go ahead turn our power supply back on. And it's not a bad idea just to test our component to make sure that everything's working properly. To test it, you're just gonna turn it on and make sure that it works properly. And you can see, we have power to the motor. Our propeller is spinning and I think we're good to go. And that'll finish up our look at and our installation of the line of pollak type one circuit breakers..
Average Customer Rating: 4.7 out of 5 stars (7 Customer Reviews)
It’s a circuit breaker and it works. I don’t know what else to say except it is not ignition protection rated so keep in mind if you are in a combustible gas environment.
Sometimes you have to call in to get help finding a product on the website. That's the only complaint about etrailer, you get too much irrelevant information in a search for a specific product. When I called in, I was able to order this relay, which fits the box I bought to hold two relays, one for power, the other for the electric brakes. Not having a circuit breaker for the power resulted in a short circuit in my tow vehicle's turn signal circuit causing them to not work.
My old harness had fallen out and I didn't notice for 700 miles; when I repaired it with a new socket, it was too short. When I jack knifed my trailer in a sharp turn, the harness was pulled out of the plug, causing the short in the turn signal harness of my tow vehicle. Having a circuit break would have prevented this issue from happening!
Use this for trolling motor on boat, works great (don't have to carry/find fuses). Have had no problems.
This was exactly what I was looking for and it arrived quickly.
Thank you,
David
Greatare standby parts
great inexpensive product
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
John
2/27/2022
I shorted out a wiring harness and lost my tailights when I jacknifed the trailer and pulled a too-short harness out of the plug. If I had a circuit breaker installed for the power current, this wouldnt have happened. I am going to protect my power and e-brake circuits with the pollak box installed with the two breakers. I also need to upgrade a short section of 16 gauge wire for my ground connection to the 7-way so the electric brakes will work reliably. I have installed a cut-off switch for the e-brake power so the controller isnt powered on unless Im towing.