This flexible, rubber line acts as part of a trailer's hydraulic braking system. Stainless steel flares, brass fittings, and a high thread engagement help prevent splits, corrosion, and leaks. Includes 3/16" FIF and 90-degree male fittings.
Features:
Specs:
Flexible Brake Hose with 90-Degree Swivel
This Kodiak brake hose is made of rubber, making it a practical choice for a variety of applications. Because you can easily bend it, a rubber hose is simpler to work with than a rigid stainless steel brake line. This flexibility makes a rubber hose great for use with foldaway trailer tongues because it is less likely to kink or break when bent. In addition, rubber hoses allow for a wide range of motion so articulating parts can effectively function. These qualities make rubber hoses better suited than steel lines for trailers with torsion axle suspension systems and trailers that have disc brakes.
And because this hose has a 90-degree fitting on one end, you can install it in tight spaces where there is limited clearance. So you won't have to make a kink in the hose to fit it up against your fender or in any other tight spot.
Stainless steel brake lines have braided exteriors, which can not only wear against exterior surfaces, but also against the interior lining of the hose if dirt gets underneath the steel braid. And if the braid on a stainless steel line tears, it can cut into the hose lining. The exterior surface of this hose is solid rubber, so there are no crevices for debris to enter.
Durable Fittings with Deep Threads
Kodiak brake hoses have corrosion-resistant brass fittings with stainless steel flares. These fittings have a gap built into them that allows room for a line wrench - also called a flare nut wrench - to slide over the line and down to the nut. This type of wrench grips the nut better than a standard open-ended wrench so there is less chance of stripping the threads as you tighten down the nut.
The stainless steel that is used to create the flares on this hose is stronger than brass. As a result, these fittings are more durable than ones made entirely of brass. The stainless flares are primarily designed to keep the fittings from splitting when you tighten them down, but they offer absolute rust protection as well.
Kodiak's fittings have deeper threads than many other fittings on the market to provide a higher thread engagement. Deeper threads offer an advantage when used with fittings that have the same thread depth. These Kodiak fittings will work with most fittings on the market, but when they're used with other Kodiak fittings, the result is a stronger connection with fewer leaks.
Average Customer Rating: 4.8 out of 5 stars (100 Customer Reviews)
This flexible, rubber line acts as part of a trailer's hydraulic braking system. Stainless steel flares, brass fittings, and a high thread engagement help prevent splits, corrosion, and leaks. Includes 3/16" FIF and 90-degree male fittings.etrailer was spot on with their brake parts and service. The quick turnaround caused very little down time!!
Perfect, fits great. Staff was very patient in helping find the right break line hose for me.
Thank you very much
Thanks again for all of the help. Here are some pics of the completed project. From new axels completely new brake system. A completer overhaul on the trailer! Thanks again for all of your help!!! Much appreciated!!!
1 year later, still works good with no leaks. My original line got damage from rubbing against the wheel. I made sure to put install a retainer to keep the lines from touching the wheel. So far so good. No issues with this hydraulic hose.
I recently purchased shoulder bolts for the Dexter brake caliber which came in 3 days down time on my trailer I use for work. Upon completing the Caliper application when bleeding discovered 1 leaking and 1 damaged r rubber line so I ordered 2 which was another 3 days down time then the lines I received needed adapters/reducers as the thread size was not the same to the Caliper which upon ordering took another 3 days of down time. My conclusion is please for business sake return to Will Call pick up, down time kills businesses...
Part was exactly as described online. Arrived quickly and on time.
Perfect fit and great price point compared to other option (different PN but same part).
Fit great. Installed on trailer with all the other brake parts I purchased from you guys. Made for a excellent resurrection of a very neglected trailer. On the road again and safely.
I love disc brakes on our 5th wheel. I didn't plan on a blowout wrecking a brake hose. My advice is to carry spares. These a great and can save a trip.
Great, rugged hose that fit my Kodiak hydraulic brakes on a Renegade stacker trailer. Keep in mind your suspension travel when measuring your hose length.
I can't see any reason this wont work just fine. It has the required DOT 'approval' stamp and is pretty flexible. With the 90 degree it should screw in the fitting of the brake actuator and make a cleaner bend through the floor of the 5ers basement then the usual hard steel line. I do wish that the rubber cover was a little heavier with some reinforcing ribbing such as what a motor vehicle uses for their hydraulic brakes. Fortunately, it will probably outlast our ownership of the RV
Installed on my 4winns boat trailer and it works.
My only problem is with the female end.
It is kind of deep and the nut/tubing flare from the master cylinder line almost wasn't long enough to engage the tubing flare at the bottom of the this part. I was ready to file off some of the hex nut surface so it would go in deeper but I tested it and it didn't leak so good enough.
This brake line was just as needed. There are numerous fitting styles for brake lines and the pictures and description on the site were excellent allowing me to choose the correct part.
I ordered 2 18" brake lines with fittings and received 2 22 in lines with fittings i must have not made myself clear
I redid the brake system on my bass boat trailer last year, and used the Kodiak brake lines. I couldn't be happier. Great product, great performance, and great customer service.
I replaced metal lines (along with master cylinder and brake assemblies on the axles) on my 30 year old boat trailer that had gotten gunked up over time. These lines were easy to install, easy to secure to the trailer rails, and have performed flawlessly.
I drove the boat to a lake 250 miles away from home last weekend, and it still stops like a dream.
Quick service, Etrailer found equivalent replacement and got product 3 weeks sooner.
What I needed and delivered fast
Arrived on time and looks like good quality product. Not yet installed. Good price and reasonable shipping rate. Thank you!
Used this hose to connect my Hydra Star Pump to my 3 axle toyhauler. Made brackets to secure the bottom end of hose to trailer. Just got it hooked up so not sure of vibration but I am comfortable knowing that the hard line will not be subject to vibration and movement. Very Satisfied.
Kodiak hose to finish installation of their disc brakes on 7000lbs axles on a Big Horn 3010 re Rv trailer. All parts where bought from e-trailer and were perfect for the install. Support group is also terrific with any information that I needed. Thanks for a excellent company to do business with!
Great Hose! I had to re plumb my boat trailer as the manufacturer left a 6" long brake line unsupported at all to connect to a female/female hose. I tried auto parts stores for a 3/16" IFT male to male connector and all they could offer was the same 6" brake line. This hose will connect directly to the caliper, eliminating the 6" line.
Absolutely fast shipping and great customer service. Mt order was actually processed on a Saturday after I ordered on Friday night!l
The brake hoses ordered were out of stock. One of the etrailer reps found this as a replacement and it worked out perfectly. I had to use less fittings than first expected.
Great brake hose, worked perfectly on my Renegade car hauler trailer with 8K axles and Kodiak 13" disc brakes.
Great, rugged brake hoses. Mine have held up great over the past year. Even with several tire blowouts these hoses are still holding up strong.
High quality product at 1/3 the cost!
etrailer really seem to care about order.
I will definitely order from them again.
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.