Custom Wiring Adapter for Hayes Brake Controllers - Dual Plug
(25 reviews)
Price: $22.49
In Stock
Custom Wiring Adapter for Hayes Brake Controllers - Dual Plug
Item # HA81795-HBC
Retail:$33.75
Our Price: $22.49
You Save: 33%
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (25)
- Q & A (0)
- Photos
Hayes Accessories and Parts - HA81795-HBC
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Hayes
- Vehicle Specific
Install your Hayes electric trailer brake controller quickly and easily with this custom wiring adapter. One end plugs into the controller, and the other plugs into the built-in port beneath your vehicle's dash.
Features:
- Plug-in wiring adapter allows for quick, simple installation of your electric trailer brake controller
- No cutting or splicing required
- Custom connector end plugs into the built-in port beneath the dash of your vehicle
- Opposite end plugs into the back of your electric brake controller
- Compatible with time-delayed and proportional brake controllers from Hayes
- Made in the USA
Installation of Hayes Brake Controller Adapter
To install your Hayes electric brake controller, you need to connect the wiring of the controller to your vehicle. Certain auto manufacturers offer pre-wired options, typically known as tow packages, in which the wiring is run for you from the dash to the trailer connector on the back of your vehicle. Usually when this is done, a port is installed at your dash so that you can easily plug in a brake controller.
This adapter plugs into the 4-pin connector on your vehicle's built-in brake control wiring harness. The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal.
No hardwiring is required to install this adapter. After you plug it into the factory port, you simply plug the other end of the adapter directly into your electric trailer brake controller. Because there are no wires to connect, installation is not permanent. You can unplug and remove your brake controller at any time to transfer it to another vehicle or securely stow it away.
81795HBC Hayes Dual-Mated Brake Control Wiring Harness - Dodge
Replaces 81795-HBC
This Product Fits The Following Vehicles
- 2015 - 2019 Ram 1500
- 2010 - 2012 Ram 1500 with factory 4-Flat
- 2010 - 2012 Ram 1500 with factory 7-Way
- 2019 - 2022 Ram 1500 Classic
- 2015 - 2024 Ram 2500
- 2010 - 2012 Ram 2500 with factory 4-Flat
- 2010 - 2012 Ram 2500 with factory 7-Way
- 2015 - 2024 Ram 3500
- 2010 - 2012 Ram 3500 with factory 4-Flat
- 2010 - 2012 Ram 3500 with factory 7-Way
- 2016 - 2019 Ram 4500
- 2016 - 2019 Ram 5500
- 2010 - 2012 Dodge Ram Pickup with factory 4-Flat
- 2010 - 2012 Dodge Ram Pickup with factory 7-Way
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
- Did not arrive in time
- Wrong item was ordered
Customer Reviews
Custom Wiring Adapter for Hayes Brake Controllers - Dual Plug - HA81795-HBC
Average Customer Rating: 4.8 out of 5 stars (25 Customer Reviews)
Install your Hayes electric trailer brake controller quickly and easily with this custom wiring adapter. One end plugs into the controller, and the other plugs into the built-in port beneath your vehicle's dash.by: Marc C11/06/2023
2019 Ram 1500
Appreciate the installation videos
by: Alan08/27/2019
Install was easy on my 2019 Ram 1500 using up to pull car Hauler Trailer. Just plugged right into the existing harness
by: Nicholas 05/26/2023
Dodge Ram Pickup
Simple easy way to connect brake controller to ram 1500
by: Patrick 03/27/2023
Great, havean’t install yet but it should be neater and easier with the pigtail harness!
by: Brian G09/02/2017
2017 Dodge Ram Pickup
Wiring harness could not be easier to install and use. Matched right up as advertised to existing wiring in my 2017 Ram 1500.
by: Merrill 12/10/2022
Accurate, detailed, discription and punctual shipping. etrailer has been great.
by: Jerry04/02/2018
2017 Dodge Ram Pickup
I ordered this for my 2017 Ram 1500. The package says it is for a 2010-2012 and 2015 Ram. I haven't tried to install it yet, but i am hoping there isn't a mistake. I can't rate this because of that. This review would not submit without a rating, so disregard the rating for now.
Rachael H.
4/3/2018
Thanks for the review Jerry, our 2015 Ram 1500 is in the 4th generation Rams that are from 2009-current 2018 and the wiring adapters for the brake controller are be the same for this generation. I hope this helps and please let us know if you have additional questions.
by: jim04/30/2017
wiring harness worked great. Got it on time and at a reasonable price.
by: Richard 10/23/2019
Worked as advertises. Plug and play in stall.
by: Phillip03/07/2017
Product came in on time. Staff was really helpful. And the plug in design took only about 15 min to install 5 stars for this company
by: jim t.12/29/2016
plug and play took only 10 mins.
by: Kyle05/11/2019
2017 Ram 1500
Plug and play very simple install
by: RWD08/17/2017
2017 Ram 1500
Makes installation fast and easy.
by: Jon07/16/2020
Plug And play super easy perfect
by: Carey02/08/2018
Made installation super easy
by: Kenn07/13/2018
made my install so easy....must have... thanks
by: darryl 01/13/2017
They told me it would be a week for delivery since it was coming by mail, I got it in three days. Very fast and easy to order.
by: David05/30/2019
Worked perfectly.
by: Dave 2018 ram 1500 eco04/07/2019
Plus in is seconds, could not be any easier.
by: Marshall 02/25/2023
by: Charles 09/24/2018
Very easy to install
by: Joseph 07/13/2023
by: Thaddeus 12/23/2022
by: Dennis 08/15/2020
perfect fit.
by: Jeff 09/10/2022
25
25
See what our Experts say about this Hayes Accessories and Parts
- Hayes Lemmerz Brake Controller Install Harness Recommendation for 2012 Ram 1500The Install harness needed to install a Hayes Lemmerz brake controller in a 2012 Ram 1500 is the part # HA81795-HBC. The adapter you sent in a picture of looks similar to what you need, but not quite the same.
view full answer...
- Brake Controller Harness for Hayes Brake Controller Install on 2016 Ram 1500We've got what you're looking for. You'll need the # HA81795-HBC harness. One end plugs into the pigtail exiting the rear of your Hayes 81770 Endeavor brake controller, the other plugs into the factory brake controller connector. The connector is located under the dash, just above where the driver's right knee would be as shown in the provided photo. I'll link to an install video that you might find helpful. The video shows a different brake controller being installed on a 2016 Ram 1500,...
view full answer...
- Brake Controller Wiring Harness for a 2017 Ram 1500 and Hayes Genesis Brake ControllerFor Hayes brake controllers the proper brake controller wiring harness for a 2017 Ram 1500 is # HA81795-HBC.
view full answer... - Recommended Custom Wiring Adapter for Hayes Brake Controllers on a 2016 Ram 1500 Yes, it will. The Custom Wiring Adapter for Hayes Brake Controllers item # HA81795-HBC will allow you to connect the Hayes Syncronizer Trailer Brake Controller item # HA81725 to your 2016 Ram 1500. The harness plugs in to the factory connector located above where you right leg would be as you're sitting in the driver's seat.
view full answer... - Will Hayes Syncronizer Brake Controller Work on a 2016 Ram 1500In the newer Rams the stoplight switch of yhe truck uses a lower voltage signal than most vehicles so only some controllers can be used. The confusion you have experienced with your local dealer and trailer shop is most likely stemming from that. We have confirmation from Hayes that their Syncronizer part # HA81725 will work on your 2016 Ram 1500 and all you would need to install it is the harness part # HA81795-HBC.
view full answer... - Correct Adapter for Hayes Brake Controller on 2018 Ram 1500The correct wiring adapter for a 2018 Ram 1500 using a Hayes brake controller such as the Syncronizer # HA81725 is the Custom Wiring Adapter # HA81795-HBC.
view full answer... - Recommended Brake Controller For 2016 Ram 1500The Hayes Brake Controller you asked about is a time-delayed controller. A time-delayed controller has a preset intensity and is activated when the brake pedal is pressed on the towing vehicle. The brake controller also has a manual override, and can be mounted at any angle or direction. For your Ram 1500 you will also need the plug-in adapter, part # HA81795-HBC. I recommend the Tekonsha P3, part # 90195. This is one of our most popular brake controllers because it is easy to install...
view full answer... - Brake Controller Harness For Installing Hayes Brake Controller on 2020 Ram 1500The correct brake controller wiring harness for both the 2020 Ram 1500 and the 1500 Classic would indeed be the # HA81795-HBC harness you mentioned. The harness plugs in to the factory connector located above where you right leg would be as you're sitting in the driver's seat. The connector you're looking for is shown in the provided photo.
view full answer...
- Hopkins Brake Controller Install Harness Recommendation for a 2016 Ram 1500The Hopkins brake controller adapter needed for installing in a 2016 Ram 1500 is the part # HA81795-HBC. One end of the harness will plug into the controller and the other will go to the port under the dash of your truck.
view full answer... - Troubleshooting Brake Controller Installation on a 2011 Ram 2500 with OEM ControllerWhen you're installing the Hayes controller, like the Energize III+ # HA81742B, on your 2011 Ram 2500 you should be able to install it by using the Wiring Adapter # HA81795-HBC. This plugs into the existing factory plug so you won't have to do any splicing with your wiring. If you're disconnecting wires and splicing the brake controller in then that may be why you're experiencing this. Under normal circumstances a brake controller should not be affecting the tail lights on the vehicle...
view full answer... - How Does Ram Factory Brake Controller Install in 2012 Ram 1500On your 2012 Ram 1500 that has a factory 4/7-way, there will be a port under the dash for connecting a trailer brake controller like the (presumably used) OEM unit you bought. There are lots of these units out there as many owner's end up replacing the OEM units with better-performing aftermarket controllers like the Prodigy P3 # 90195. The controller does not require any programming to operate. The vehicle computer may need to be flashed by the dealer if you find you get error messages...
view full answer... - Bypassing Factory Brake Controller (ITBC) on 2017 Ram 3500Even after they've been out for more than 10 years, we continually hear complaints from folks about the factory integrated brake controllers on their trucks. We never seem to hear "I love it, it works great!" From what I understand, the factory brake controllers have a power adjustment that allows you to increase or decrease the intensity of the braking force and a manual switch that applies the trailer brakes independently of the truck brakes. That's it, no further adjustments are possible. If...
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Jameson C
Edited by:
Lindsey S
Updated by:
Laura H
Updated by:
Wilson B
Installed by:
Cole B
Written by:
Tammy D
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Brian G.
9/21/2018
No problems however for my 10 ft pop up there is a bit too much gain. At the minimum setting the trailers brakes in my opinion are a bit heavy