Screw - Self-Tapping Phillips Head - 8-18" x 3/4"

See what our Experts say about this Flint Hill Goods Accessories and Parts

• How To Attach the Black Molded Fender Bracket A67BB
  In order to attach the Black Molded Fender Bracket part # A67BB I recommend using the Self-Tapping Phillips Head Screw part # 1131832 because the head will sit closer to the base and will allow for the Optronics Thinline LED Trailer Fender Light part # MCL65ARB to sit flush. The Black Molded Fender Bracket we offer grounds via the mounting hardware so a ground wire is not present but if you have a version of this bracket that does have a ground wire then you can just snip this and tape...
  view full answer...
• How To Install the Optronics Thinline LED Trailer Fender Light
  The Optronics Thinline LED Trailer Fender Light part # MCL67ARB comes with a mounting bracket so as long as the surface you will be installing it on is metal then yes, it will work for you. All you would need to do to install the light is use two self tapping screws like part # 1131832 to mount the base and then once this is done you can attach the light to the base. To complete the process you will then need to attach the black wire to the running light circuit on your trailer which is...
  view full answer...
• Why Are the Holes On the Back of the Automatic Changeover RV LP Gas Regulator Not Threaded
  Yes, you will need to use self-tapping screws like part # 1131832, not bolts which will form their own threads when mounting the Automatic Changeover RV LP Gas Regulator part # 37207-30395.
  view full answer...
• Hardware Needed For LaSalle Bristol CrossBreeze Adjustable Toy Hauler Screen
  The LaSalle Bristol CrossBreeze Adjustable Toy Hauler Screen - 92" Wide Item # 3441409200PBK just requires some self tapping screws like Screw - Self-Tapping Phillips Head - 8 x 3/4" Item # 1131832.
  view full answer...
• Installation of UWS Truck Bed Tool Chest UWS01044 in 2018 Sierra Denali 2500 HD
  The UWS Truck Bed Tool Chest # UWS01044 does require you to drill and use your own hardware to secure it in your truck bed. The choice of hardware is up to you; you could use screws, nuts and bolts or even u-bolts like # CE15252A if you prefer. Your spray-on liner will not be an issue for installation. Dimensions are shown in the linked diagram. This USA-made tool chest features 8 cubic feet of internal volume and its corrosion-resistant aluminum construction and foam-reinforced lid mean...
  view full answer...
  
• Comparing Trailer Horse Pad Screws and Self-Taping Screws for Horse Trailer Side Pads
  The Trailer Horse Pad Screw part # PS-8 will work great for attaching Horse Trailer Side Pads like part # HTP60BK. That said, you may need to drill a small pilot hole into the backing first depending on the material. I suppose you could use a standard self-tapping screw like part # 1131832 as well but there is no built-in washer on these and you risk stripping the hole much easier this way as well.
  view full answer...
• Replacement Trailer Clearance Lights for Bargman 99 Series
  The correct replacement trailer clearance light for a Bargman 99 Series is the Optronics Trailer Clearance or Side Marker Light part # MC44RB for red or part # MC44AB or amber. The mounting holes for this light are spaced 3" apart on center. It features a simple two wire installation, one for power and one for ground. In order to remove the old lights it would be easiest to just drill out the rivets with a small drill bit. The drilled holes would then make good pilots for the self tapping...
  view full answer...
• RV Slide-Out Topper Mounting Hardware
  The Replacement Mounting Hardware for Lippert Solera Slide Topper - Black # LC701665 will help you get the parts you are missing.
  view full answer...
• Recommended Door Holder for Fender Mounting
  The Plastic Stem and Rubber Socket Door Holder - 2" Long Stem # DH39R can be installed onto your fender if desired to allow your door to be secured open. You can alternatively use a Hook and Keeper for Enclosed Trailer Door # 383400 in another location like mounted to the fender to give you a similar option. There is not an option we carry that is long enough to allow connection to the main trailer wall when the fender is making contact with the door.
  view full answer...
• Will LED Clearance Light Work With One Wire
  Yes, the Thinline LED Clearance and Side Marker Light - Submersible # AL91AB will work with your single power wire, as it uses a 2-wire (one for power, one for ground) pigtail or 1-wire pigtail with a self-grounding bracket. To mount this light you have a couple options. The first is the Mounting Bracket # A91BOB with Right Angle 2-Wire Pigtail # A46PB; you'd also want to use the Self-Tapping Screw # 1131832. Your other option to mount this light is to use Self-Grounding Mounting Bracket...
  view full answer...
  
• Recommended Light for RV Storage Compartment
  The LED Utility Light with Switch part # 328-001-504E is my recommendation for a storage compartment light as it is battery powered so you don't have to worry about routing wires to the storage compartment which can be a huge hassle. The battery will also last a long time as the LED's draw very little power so you won't have to worry about changing out the battery frequently. In order to install the light you just simply remove the lens, mount the base with screws like part # 1131832,...
  view full answer...
• What Hardware Is Needed To Install the Thinline LED Trailer Clearance or Side Marker Light MCL67AB
  The Thinline LED Trailer Clearance or Side Marker Light part # MCL67AB is a surface mount light that has two mounting holes which you will see once the lens is removed. In order to mount this you can use pretty much any self tapping-screw like the Self-Tapping Phillips Head Screw part # 1131832. The Self-Tapping Phillips Head Screw could be used to mount most of our trailer side marker/clearance lights.
  view full answer...
• How to Install Side Marker Light
  To install a side marker light like the Optronics # AL82AB on your 2014 Malibu you will need to ground the white wire and then connect the black wire to your running light circuit. This then installs on the mounting bracket # A91BOB which you will need install using something like a self-tapping screw # 1131832. Sometimes the lights ground via the mounting hardware so if that's the type of light you have you need to make sure that you mount it to a clean, bare-metal surface. Attached...
  view full answer...
  
• Which Replacement Bulbs for Optronics CB22AB Triangle Truck Clearance and Cab Marker Light
  The Truck Clearance and Cab Marker Light - Incandescent - Triangle - Amber Lens # CB22AB uses the Replacement Side Marker Light Bulb # 194 # A194B. These do not have specific mounting hardware that is used, but some stainless steel self-tapping screws like the # 1131832 would work.
  view full answer...
• Replacement for Reflect-O-Lite 400
  The Reflect-O-Lite line has been discontinued for quite some time so replacements are no longer available. However, the Trailer Clearance or Side Marker Light w/ Reflex Reflector part # MC32AB is a very similar option that will work well in its place. In regards to installation, all you will need to do is mount the base with a screws part # 1131832 and then match up the wires with butt connectors part # DW05744-5.
  view full answer...
• Wiring Configuration for Trailer Side Marker Lights
  The usual configuration for 4-pole trailer wiring has the WHITE wire as GROUND, the BROWN wire as RUNNING LIGHTS, the YELLOW wire as LEFT TURN/STOP and the GREEN wire as RIGHT TURN/STOP. If your light has white and brown wires coming out of it then typically the brown wire would connect to the + side of the running light circuit and the white wire would ground to the trailer frame, or could be run up to the trailer plug's ground. One way or the other the light must have a ground and a +...
  view full answer...
• Most Popular Replacement Clearance/Marker Lights for an Old Travel Trailer
  The most popular clearance/marker lights we offer are the Optronics Clearance or Side Marker Lights w/ Reflex Reflector. These are offered in both incandescent part # MC38AB for amber or part # MC38RB for red and LED part # MCL31AB for amber or part # MCL31RB for red. They have a two wire design so they are super easy to install. The white wire gets grounded and then the back wire goes to the running light circuit with butt connectors part # DW05744-5. If you need screws to attach the light...
  view full answer...
• Is Mounting Hardware Included with the Jensen Double DIN RV Stereo
  This is correct; since the Jensen RV Stereo # JWM45 is designed to be mounted in different manners, mounting hardware is not included. You'll want to use mounting hardware appropriate for your mounting method, so if you're mounting it in a cabinet you'd just need some wood screws.
  view full answer...
• What Size Screw Is Needed To Install the Optronics LED License Plate Light Part # LPL59CB
  The two mounting holes on the Optronics LED License Plate Light part # LPL59CB are .2" diameter which means you can use the Self-Tapping Phillips Head Screw part # 1131832 to attach them to your trailer. In order to make the wiring connections you can use the Deka Heat Shrink Butt Connectors part # DW05744-5. This will be everything that you need to install the light for the exception of a phillips head screwdriver and pair of pliers.
  view full answer...
• How To Mount the Optronics LED Clearance or Side Marker Light w/ Reflex Reflector Part # MCL31AB
  The Optronics LED Clearance or Side Marker Light w/ Reflex Reflector part # MCL31AB mounts by running two screws like part # 1131832 though the base. In order to access these screw holes you will need to remove the lens. I have attached a photo that shows the screw holes. I have also attached an install video for you as well. In order to make the wiring connections you will also need part # DW05714 and part # DW05737-1.
  view full answer...
  
• Can the Horse Trailer Breast Pad Be Attached Directly to Metal
  The Horse Trailer Breast Pad part # HTP24BK could easily be attached to a metal divider using self tapping screws like part # 1131832. I would agree that generally speaking the breast pads are attached to plywood but I don't see an issue attaching them to metal either.
  view full answer...
• Can a Heat Shield be Sandwiched Between the Frame and Trailer Hitch
  The Curt Trailer Hitch Receiver part # C12111 on your 2017 Ford Escape will need to be attached directly to the frame without anything between it. Sandwiching the heat shield between the frame and hitch will affect the integrity of the hitch and void Curt's warranty. Therefore, I cannot recommend you sandwich the heat shield between the frame and the trailer hitch. In order to further secure the heat shield onto the body of your Escape, you can always use a few self tapping screws like...
  view full answer...
• How To Mount the Optronics LED Trailer Tail Light # STL42RB
  I am not entirely sure what you are asking but the Optronics LED Trailer Tail Light part # STL42RB is a flush mount trailer light that is designed to be installed on a flat piece of metal in a 4-1/2" diameter round hole with a self tapping screw like the Self-Tapping Phillips Head part # 1131832. The thickness of the metal that the light installs in is not an issue. The overall depth of the light is 1-15/16" thick. For a pigtail harness we have two options for you, part # A45PB or part...
  view full answer...
• Hardware for Tekonsha Mounting Kit # 5280
  The Mounting Bracket # 5280 for your Envoy brake controller does not include the mounting hardware and Tekonsha does not provide this. To mount the bracket all you need are some 3/8 inch screws like # 1131832. You can also just obtain some at a local hardware store if that is easier. The holes on the bracket will match up to the mounting hole pattern on your Envoy.
  view full answer...

Do you have a question about this Accessories and Part?