1/2" Diameter nylon brush is great for cleaning out weld nuts on vehicle frames - makes your hitch installation much easier!
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to review part number 814092. This is the Fastenal half inch nylon tube brush. This brush is great for cleaning out well nuts on your vehicle frames when you're installing a hitch, makes that install much easier. We use it here at Etrailer. This nylon brush has a nice metal design, has a loop handle on the end that help you hold it. It does use nylon filled bristles on the brushes.
This used in cleaning and deburring any of the well nut holes. Dimension on this, overall length, to give you an idea, it's going to be 8.5 inches. Just the brush itself, the bristles is 3 inches. The diameter is half an inch on the bristles themselves. Basically, what you'll use this for is you want to start by soaking the well nut bolt holes on the frame of your vehicle with a penetrating lubricant, and then let the lubricant soak in a while. Then you take this nylon wire brush, stick it up into the holes, move it around, and basically that'll scrub out the holes and free any dirt or rust from inside those holes.
It's actually very helpful on any vehicles that have a few years on them. Newer vehicles might not be as bad, because it didn't have time to build up. On some of the older vehicles, it's good to have this clean out anything in those well nut holes. You might have to do it a few times, but it should allow the bolts . You take one of the hardware bolts. Once you get it cleaned out, try it in there, make sure it threads in a lot easier.
It does save you a lot of time, makes the bolt fit more easy. That should do it for the review on part number 814092. This is a Fastenal half inch nylon tube brush.
Average Customer Rating: 4.7 out of 5 stars (488 Customer Reviews)
1/2" Diameter nylon brush is great for cleaning out weld nuts on vehicle frames - makes your hitch installation much easier!The brush is very easy to use. I still use it to clean out road debris from bolt holes in my car and hitch.
So far so good. Took approximately an hour to install, including unpacking the hitch and cleaning out the weld nuts. While potentially possible to install on your own with strategically placed supports, it's more realistic to install with two people, even if one of them is just lifting, steadying, and holding the hitch in place while you do all the work. Everything lined up perfectly. Didn't even need to put the van up on ramps. Trimmed the plastic fascia on the driver side as shown in the video instructions and worked like a charm to reinstall.
Test fit our bike rack (which is our primary intended use) and everything fit snuggly. So far, very happy with the purchase.
Work like a charm to clean out rusted welded nuts. Combined with BP Blaster I was able to thread my bolts fairly quickly.
I was unable to find a brush like this in the local stores. I use it to clean the threads underneath the car where the bolts to the trailer hitch get installed. Essential tool especially if the car has some years and miles on it. I have used in conjunction with the proper size tap to ensure threads are clear and clean.
It was very easy to install and it met all my expectations. The video on-line was very helpful in understanding the entire process before we bagan instalation. Ashley at etrailer was most helpful in making sure we got the right product for our car. Our plan is to use it exclusively to haul our bicycles around with us as we travel. We will definately look at the bike racks etrailer has to offer as well.
Easy to install, especially with the available videos. Works great!
Brush worked exactly as expected, although in the course of the last year, it has gotten only limited use. Initially, it was used to help clean the pre-drilled holes for the receiver, and it worked perfectly.
The whole process from ordering to getting the hitch was awesome. It arrived a lot quicker than I thought it would. I have not been able to install it just yet due to a cold snap in our area. Daytime high of 15 degrees and no garage to work in, makes it too difficult to do it. I am anxious to get it put on the Rav4 . The only minor problem we had was the carton was taped up by UPS due to the hitch breaking out of the carton on one side. The other side did start to a little bit. Would recommend them increase a little more packing material around the square mounting brackets to eliminate that problem. Otherwise, awesome !
Great for cleaning out bolt holes.
Great product..."Plug and play" with my vehicle. Clear directions for install.
Good product, steel handle with sturdy nylon brush, well packaged and fast shipping
Easy installation, low profile and excellent quality. Exactly what I was looking for in a hitch receiver for our 2021 Pilot.
perfect item to clean out the bolt holes as I installed the hitch 4 years after the car was originally purchased.
It's very solid, and supports our bike rack just fine. It was installed on a 2007 Toyota Sienna and I had to take it to our local auto shop because I didn't have a tap and die set to bore out the rusty pre-drilled holes. It does sit a little low, so be careful when backing up near curbs. You'll definitely scrape! Otherwise, very happy with it so far. Oh, and the shop had to adjust our exhaust a little bit because it hit the hitch receiver when we hit bumps.
Great price. Helped cleaning out the th reads
Just a brush, worked as advertised
This brush is okay, but from personal experience, to get all of the crud and rust out, I used a standard plumbing wire brush tool. The same one you would use on copper tubing or on your car battery. It's an all in one. This cleaned the threads better. See pic.
This is the right size for the threaded mounting holes in the frame. Since I didn't have WD-40 spray, I was able to use my WD-40 pen applicator to wet the brush first - then it worked great! FYI - It was still necessary for me to use a thread tap, as well.
Great brush, as described.
I'm going to be completely honest and review this product from start to finish. Finding the "hidden hitch" online was extremely easy. Their website walks you right through finding the correct one for your vehicle and they have an enormous inventory of everything you could need for towing. I have a 06' Honda Odyssey. The videos were greatly helpful to watch before receiving the hitch so I knew EXACTLY what to do when installing the hitch. I decided to buy one and was genuinely excited to get this thing on our Honda. Their tracking service was accurate and informative, showing me where the package was with a picture of it moving across the states. Package arrived late in the evening (7:45pm) and the box it was in had been completely destroyed. Both ends of the box had to be heavily repaired with packing tape and there were holes, drag marks, etc all over this box. As for the product inside? It had plenty of scrapes, dents, dings, etc. Now this thing is solid steel so I wasn't really concerned about the cosmetic condition of the hitch. Just shows you that UPS does NOT care about your packages, when you receive them and will destroy them. You should package items like they are going into war. Used the spiral brush to clean the threaded holes on the frame of the Honda and used one of the bolts to make sure they would screw in quickly and easily.... they all did. Took 20 minutes to put the hitch on myself (I used a few small boxes to hold the hitch into place under the rear of the odyssey or there abouts until I could put in all the bolts, spacers and washers. The information on the install sheet was easy to follow and had all the vital information, like torque specs. Installing the wiring harness for the trailer was ridiculously easy. I thought it was going to be a hassle, cutting wires, dealing with electrical tape, trying to figure out where wires come and go, etc but it wasn't. I pulled off a panel and then the side panel. The wires literally just PLUG IN to a control box and the ground wire gets bolted (small bolt) to the grounding unit. Then you just run the wire along existing wires, zip tying along the way, feed the wires through to the spare jack compartment for storage. Then I had to just plug in a fuse, provided by them, into the fuse board and I was done. It took me about 1 hour to install the hidden hitch and the wiring harness and be completely tow ready....amazing. Overall quality of materials, wires, product: 10/10. Customer service, instructional videos, installation instructions: 10/10. Timeliness of purchase, shipping and installation: 10/10. Condition box/product was received in: 4/10. I would HIGHLY recommend this product and etrailer.com. It is a SOLID piece, easy to order and install to make your vehicle tow ready. This set up was the easiest thing I have EVER installed on a vehicle, very pleased overall with the end result. Here are a couple pics of the hitch installed and the trailer wiring harness ready to go.
Worked great to clean out 1/2" nuts on my car before threading bolts into them.
After balking at the cost to have an auto-shop add a trailer to our Toyota Highlander, we found etrailer.com and decided to take a chance. The "how to" videos factored considerably in our decision to buy ... they made it look so easy! And surprise! It really -WAS- that easy. We used standard block-type ramps (the kind you can buy for $40 ) to get the SUV up off the ground high enough to get underneath to do the work. Everything came off as easy as it was showed in the videos. Other than the fact this bar is a heavy so we had our teen daughter help hold it steady while we bolted it into place (i.e., get help for when you go to lift it), it went super smooth. Thanks for saving us $280 over the cost the car dealer quoted us! P.S. - be sure to watch the linked videos so you get the right trailer lighting attachment and ball hitch for your new hitch.
does the job
over priced brush that is NOT needed. After reading the installation literature I felt it was needed but I think I was gas lighted into thinking there was a need.
Works fine for dirt and debris, but does not work with nuts that are welded in the frame and have rusted. I would like to see you offer a tool to assist in removing the rust from a nut. I used a rotary tool with a small steel brush but it wasn't ideal, as it was too large.
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.