Dutton-Lainson Electrical Quick Connect for DC StrongArm SA Series and TW9000 Electric Winches

See what our Experts say about this Dutton-Lainson Accessories and Parts

• What Size Wire is Recommended for Use in the Electrical Quick Connect for Electric Winches
  Normally 6 gauge wire is used for winch wiring applications. If your application does not require the high amperage draw that a winch requires then you could use 8 gauge wire in the connector tips. Any smaller wire than that would most likely not stay in the tips too well after soldering.
  view full answer...
• Can Quick Disconnects be Used to Easily Connect to Battery of Trailer
  You could use a set of quick disconnects like part # DL24085 to make disconnecting from your trailer battery easy. You would just wire the power and ground to each of the terminals and then it would be good as-is.
  view full answer...
• Can Electrical Quick Connect Be Permanently Mounted
  The holes that are on the Electrical Quick Connect, part # DL24085, can be used for mounting. You would need to make certain that the polarity of the wires you are using are lined up correctly and also need to make sure the hardware you use is the correct size so that you do not damage the connector when mounting.
  view full answer...
• Does the Dutton-Lainson Quick Disconnect Winch Harness # DL24151 Include Both Male and Female Ends
  The Quick Disconnect Wiring Harness you mention, part # DL24151 is designed to plug directly into the winch, as shown in the photo I produced for you. According to the instructions, the wiring harness is meant to be unplugged and stowed in the tow vehicle when not in use. If you wanted to construct a quick disconnect jumper, you could do so by using part # DL24085 and the appropriate length of 8 gauge wire. The plugs would be installed on both ends of your jumper, which could be used to...
  view full answer...
  
• Is There a Harness That Goes Between Truck and Trailer When Using Dutton-Lainson Electric Winch
  In regards to the Dutton-Lainson StrongArm Electric Winch part # DL25215, the winch wiring harness is designed to attach to a vehicle battery and then run from the front back to the bumper so you can attach to the winch on the trailer when needed. There will be extra wire that will be simply coiled up and stored on the truck while not in use. If you wanted to cut the wire at the bumper you could then make a quick-connect system between the truck and trailer using the extra wire and Dutton-Lainson...
  view full answer...
• What Size Wire is Compatible with Electrical Quick Connect for TW4000 Electric Winches, # DL24086
  The Dutton-Lainson Electrical Quick Connect for TW4000 Electric Winches, # DL24086, accepts up to 10 gauge wire. To secure the wire, you will need to solder it into place as it cannot be crimped. This product is designed for use with TW4000 electric winches. We also carry the Dutton-Lainson Electrical Quick Connect for DC StrongArm SA Series and TW9000 Electric Winches, # DL24085, which accepts 6 to 16 gauge wire. It is designed for use with DC StrongArm SA Series and TW9000 Electric Winches.
  view full answer...
• How to Release Quick Connect Electrical Connections
  Quick connects like the Dutton-Lainson Electrical Quick Connects # DL24086 that you referenced do not have a release latch built into them. Basically you just slide them apart. They can sometimes be difficult to get apart, but if you wiggle them while pulling on them they will release.
  view full answer...
• Recommended Electric Boat Winch For 4000lb Fiberglass Boat
  The Dutton-Lainson StrongArm Electric Winch - Marine - 9,000 lbs # DL25215 would be plenty strong to pull your 4000lb fiberglass boat on your bunk trailer, and already includes a 2" x 20' polyester strap so you will not need to purchase one separately. Since the wiring included with the # DL25215 has a quick connect already on it you can run that to the battery on your truck and mount the quick connector near your 7-way like you mentioned. You will then use the Dutton-Lainson Electrical...
  view full answer...
• Using Dutton-Lainson Quick Disconnect to Wire Hose Reel Motor
  6 gauge wire can handle up to 55 amps, so the wire and the # DL24085 quick disconnect you're planning on using should work very well for you. The connector is designed for use with 6 gauge wire, so the wire and quick disconnect will be compatible with the power draw of your motor. I've linked to a product description video for the quick disconnect.
  view full answer...
• Can a Winch Be Powered From a Truck Battery Using Battery Cables
  Yes, you can wire your winch with clamps to the truck battery. 2 gauge wire should be sufficient for a 5,000 lb. winch. If you wanted to be sure, you can look in the owners manual to verify the wire gauge needed for your particular winch. You can use something like the Bulldog Winch Booster Cable Set # BDW20233. You would just likely need to cut off one end and wire it to your winch.
  view full answer...
• How many Quick Connectors are Included in the Dutton-Lainson Electrical Quick Connects # DL24085
  When ordering the Dutton-Lainson Electrical Quick Connect, # DL24805, you will get 2 plastic connectors, one male and one female and 4 quick connect terminals, properly sized for soldering 6 gauge wire into them, to make one complete quick disconnect setup. If you are using a larger gauge wire for installation of a large winch, you would need to go with the Superwinch Quick Connects, # BDW20133, for 2-4 AWG Wire.
  view full answer...
• Are there Quick Disconnects for an Electrical Winch with 5 Gauge Wiring
  The best match that we have for a 5 gauge wire is going to be the Quick Connects, # BDW20018. It fits 3 to 5 gauge wire. The other options we have would be too small (6 to 10 gauge) so going larger would be the way to go.
  view full answer...
• Mounting Bracket for Winch Quick-Connect Wiring
  We do offer quick-connect winch wiring kits like # DL24085 and # DL24086 from Dutton-Lainson which are intended for specific winch products (based on their power requirements). Although we do not have a water-proof mount for these (or the Anderson SB50) we do offer a no drill bracket # C57202 which you could use as a mounting point for one of the connectors. These connectors have holes in them to allow for either securing one half of the connector to a trailer surface (the mounting bracket...
  view full answer...
• Will Dutton-Lainson StrongArm Winch DL25010 Work With 2023 Yamaha SX190 Jet Boat?
  They sure will! The following components you were looking at will all work perfectly with your new 2023 Yamaha SX190 Jet Boat: Strong Arm Winch # DL25010 Quick Disconnect Connectors # DL24085 Winch Cover # DL24051 With that said you shouldn't need the Mounting Bracket # DL24059 as your boat trailer should already have a standard winch mount for the winch to install.
  view full answer...
• Is a Wire Needed Between the Alternator and Redarc In-Vehicle BCDC Battery Charger
  Yes, you will have to run a power wire from the alternator to the Redarc In-Vehicle BCDC Battery Charger part # 331-BCDC1225D which gets installed on the trailer, there is no way around this nor would there be for any other battery charger of its kind. The correct size of wire to use will have much to do with the length between the alternator and trailer battery. Most likely you will need a 6-8 AWG wire. If you have any local car audio stores nearby they will most likely be able to sell...
  view full answer...
• Solution for Powering Air Compressor With 7-Way
  You can use the Pollak 7-Way to 12 Volt Power Outlet Adapter # PK11896 but you will need to switch out the connector on your air compressor. You will need to find a male cigarette plug that is rated the same or higher. If you decide to run a line from your battery you will want to use the same gauge wire that your compressor uses. The largest size we carry is 10 gauge # 10-1-1. Once you run the wire you can use the Dutton-Lainson Electrical Quick Connect for DC StrongArm SA Series and...
  view full answer...
• Availability of Longer Wiring Harness for Superwinch Winch 2 Go # SW1140232
  Your best bet to install the Superwinch Winch 2 Go in the manner you described would be to use the Bulldog Winch Wiring Kit, part # BDW20206 along with part # DL24085. You would then remove the connectors on the # BDW20206 and replace them with those provided by part # DL24085. Once the connectors are replaced, the quick disconnect provided by the wiring kit would plug right into the connector on the winch. According to my Superwinch contact, a longer power cord that has the alligator...
  view full answer...
  
• Adding Electrical Connector for Wash Down Pump on a 2005 Dodge Ram 1500
  I have a simple solution that I think you will like. All you will need is some 10 gauge wire, # 10-1-1, and some quick connectors, # DL24085. For the wire you will change the quantity to the amount of feet you will need which will depend on where you want the connector to go on the truck. You would attach the power (and ground if applicable) wires to one of the connectors from the pump. The other connector will use the 10-1-1 wiring and will need to connect to the positive battery terminal...
  view full answer...
• How To Add Quick Disconnect Harness for Electric Boat Winch
  I may have a solution for you, but there's not going to be a wiring harness that can be used that will provide you with the power you're going to need to pull from the battery to power the winch. Your best bet might be to create some sort of quick disconnect for each of the batteries that you can either hook up when needed, or leave attached to the vehicles. This would require cutting off the battery clamp ends of your winch and putting quick disconnects like the Dutton-Lainson Electrical...
  view full answer...
• Options for Installing a Plug-In Style Connector for a 12v Air Compressor for a 2006 Chevy Duramx
  I assume you want to use a 7-way connector, like part # PK12706, on your 12v air compressor to power the compressor using the 7-way trailer connector on your truck. You can use a 7-way trailer connector on your air compressor as long as the wire size for the power wire and ground wire from the compressor are not thicker than the 12 volt power wire and ground wire on your truck. The ground wire and 12 volt power wire on your truck are likely either 10 or 12 gauge wire. If your compressor...
  view full answer...
• Quick Connects for Power a Trailer Winch from a Vehicle Battery
  There are some quick connect options for winches. We have # BDW20133 for 2 gauge wire, # BDW20047 for 6 gauge wire. We also have # DL24085 for 6 to 16 gauge wire and # DL24086 that accepts up to 10 gauge wire. I have included a link to our FAQ article on wiring an electric winch that should be helpful.
  view full answer...

Do you have a question about this Accessories and Part?