Dexter Electric Brake Assembly for 4 Bolt or 5 Bolt Flange - 12" - Right Hand - 6,000 lbs

See what our Experts say about this Dexter Accessories and Parts

• Center Hole Diameter of Brake Assembly 23-106-09
  The center hole of the brake assemblies # 23-105-09 and # 23-106-09 measures 3-3/16 inches across. The kit for both of these is the part # 23-105-106-09 that you referenced.
  view full answer...
• Replacing Brakes On A 1989 Silver Streak Travel Trailer With Hadco Axles
  That is a neat looking camper. 1989 was a good year. Honestly, the same answer will apply to the brakes on your 1989 Silver Streak Travel Trailer. The 12" x 2" brakes are still standard. We will just need to make sure that the brake mounting flange bolt pattern matches up. These days the 5 bolt flange, like on part # AKEBRK-7-SA is standard for the 12" brakes. I have included a diagram showing the dimensions of the standard 5 bolt brake flange for your reference. We do not have a record...
  view full answer...
  
• How to Determine if Trailer Brake Assemblies 23-106-09/23-105-09 Fit Trailer
  I can help you find the right assemblies, but I do not know exactly which ones you have on your trailer. To pick out the correct brake assemblies for your trailer you need to know a few things. You will want to measure the inner diameter of your hub/drums and the depth of the drums to determine what brake assembly dimensions you need. For example the part # 23-105-09 is a 12 inch by inch thick brake assembly. You also want to determine what the bolt pattern is of your assembly mounting...
  view full answer...
  
• When Should I Replace My Brakes On The Dexter Electronic Brake Assembly # 23-106?
  I reached out to Dexter about your specific question concerning your brakes # 23-106-09. A simple visual inspection of your brake linings will tell if they are usable. Replacement is necessary if the lining is worn to 1/16" or less. Shoes contaminated with grease or oil, or abnormally scored or gouged should also be replaced. Hairline heat cracks are normal in bonded linings and should not be cause for concern. When replacement is necessary, it is important to replace both shoes on each...
  view full answer...
• 7,000 lbs Electric Drum Brakes on a 5,200 lbs Axle
  Yes, you can use the Dexter Electric Trailer Brake Kit - 12" - Left and Right Hand Assemblies - 7,000 lbs item # 23-180-181 on your 5,200 lbs axle so long as you have a 5 bolt flange like the one linked in the diagram below. These brakes fit a 12" x 2" drum. Another option is to use the Dexter Electric Brake Assembly for 12" - Right Hand - 6,000 lbs item # 23-106-09 and the Left Hand item # 23-105-09 which fit both 4 Bolt or 5 Bolt Flanges.
  view full answer...
  
• Electric Trailer Brakes to Replace Hayes/AL-KO Brakes on a Homemade Trailer
  It sounds like you have the brake mounting flange for Hayes/AL-KO brakes. The standard 5-bolt brake mounting pattern on # AKEBRK-6 will not work. We do have brakes that have that mounting pattern though. You will need # 23-105-09 for the left and # 23-106-09 for the right. I have included a picture showing the hole spacing of these brakes for you as well.
  view full answer...
  
• Brake Assembly Recommendation for a 6k Dexter Axle with 12 inch Assemblies
  Sorry about the problems you were having with our brake install/setup video. We have been having some issues with our servers here lately so that is probably why. For a 6k, 12 inch brake assembly with a 5 lug install bolt pattern you would want the part # 23-458 for the left hand side and part # 23-459 for the right hand side.
  view full answer...
• Parts Availability for Rebuilding Dexter 12-Inch Electric Drum Brakes on Dump Trailer
  We do stock all types of replacement parts for electric drum brakes like the 12-inch Dexter 6K brakes # 23-105-09 (left) and # 23-106-09 (right). These items are not kitted together but you can see each item we have, from magnets to brake shoes to mounting hardware, on the linked page. Often it actually costs less to replace an entire brake assembly than to replace almost all of the individual parts. So I linked our main page for complete electric drum trailer brakes in case you prefer...
  view full answer...
• How to Determine if 6k Dexter Electric Brake Assembly for 4 Bolt or 5 Bolt Flange Will Fit Flange
  You'll need to do some quick measuring of your backing plate/brake flange to see if you can use the 6,000 lb Dexter Electric Brake Assembly for 4 Bolt or 5 Bolt Flange - 12" - Left Hand # 23-105-09. I have added photos below that I hope will help. One is of a standard 5-bolt brake flange where the bolts are 2-1/8" apart except for the bottom which are 3" apart. The other photo is of is the brake assembly which shows the dimensions of the AL-KO/Hayes 4-bolt flange, where the holes are 3-1/8",...
  view full answer...
  
• Replacement Brakes for Dexter Axle 6K Axle
  From what we've found in the past people with the number 90817 are for 6K brake systems so you need the following parts: - Right Hand Assembly # 23-106-09 - Left Hand Assembly # 23-105-09 I've a photo showing the mounting bolt pattern for these brakes for you to compare and confirm what you what with these brakes.
  view full answer...
  
• How To Determine if Dexter 12x2 Electric Brake Assembly # 23-106-09 Will Fit 1982 Silver Streak RV
  The same answer would apply. The brake assembly # 23-106-09 is designed to fit a Hayes/AL-KO or Dexter axle with either the 4-bolt or 5-bolt mounting flange. These are 12 x 2 inch brakes. To measure the drum you will measure the inside diameter. It should be 12 inches. Then measure either the width of the old pad or the width of the surface it would contact on the inside of the drum. That should be 2 inches. These brakes are designed for 6,000 pound axles but could also be used on a 5,200...
  view full answer...
• Replacement Brake Assemblies For Al-KO Or Hayes 4-Bolt Flange
  The closest brake assemblies we offer to the dimensions you said you have are part # 23-105-09 for the left hand, and # 23-106-09 for the right. The 4-hole bolt pattern is 3-1/4 inches for the top two holes, 2-1/2 inches for the lower two holes and the distance top to bottom is 3-3/8 inches. I know the measurements are off by 1/8 inch versus your measurements but I am sure these are what you are looking for. These are designed for either AL-KO/Hayes 4-bolt or standard 5-bolt flange and...
  view full answer...
• Available 12 x 2-Inch 6K-Rated Electric Trailer Brakes with 4-Bolt Mounting Pattern
  All of our 12 x 2-inch 6K-rated electric trailer brakes are shown on the linked page. Most of these use the 5-bolt mounting pattern but a few Dexter products include holes for BOTH bolt patterns, both 5-bolt and the 4-bolt Hayes/AL-KO pattern, parts # 23-105-09 (left) and # 23-106-09 (right). We also offer them as a set, part # 23-105-106-09.
  view full answer...
• 12 x 2 Inch Electric Trailer Brakes with a 4 Bolt Mounting Pattern
  The 4-bolt brake mounting pattern is fairly rare in a 12 x 2 inch assembly. We have some options though; for 6K axles we have # 23-105-09 for the left and # 23-106-09 for the right. The 4-bolt pattern on these assemblies is offset meaning the bottom 2 holes are closer together than the top 2 holes. If that is what you have then either set listed above would work. I have linked videos on each of these types of brakes for you.
  view full answer...
• Replacement Trailer Brake Assemblies that Have 4 Bolt Pattern and 12 inch Diameter
  Your dimensions are a little unique but I would assume you have an AL KO brand axle with a 6k axle and the correct assemblies would be the part # 23-105-09 and # 23-106-09. This is 12 inch in diameter assembly that can attach with a 4 or 5 lug bolt pattern. I would recommend checking the axles for a tag that has it's capacity listed or see if there's a part number you can see on old assemblies/hubs to verify this.
  view full answer...
• Replacement 12 inch Brake Assemblies for Prowler Trailer With 4 Bolt Mounting Flange
  Definitely looks like you have the Hayes 4 bolt style of 12 inch brake assemblies. So for the right hand side you'd want the part # 23-106-09 or for the left hand side part # 23-105-09. We wouldn't have just magnets for your assemblies but by the overall condition of your assemblies just replacing them would be your best option.
  view full answer...
  
• Recommended Electric Brakes for 1986 Royal Internation Sportman 32 with Hayes 12x2 Brakes
  Thanks for your picture it was a great help! Looks like your 1986 Royal International Sportman 32 had the older Hayes brakes. The correct replacement assemblies for this are the # 23-106-09 for the right hand assembly and # 23-105-09 for the left hand assembly. I have linked them to this page for your purchasing convenience.
  view full answer...
  
• Replacement Parts for Dexter Nev-R-Adjust 12 x 2 Inch Electric Trailer Brakes
  Those are 12 x 2 Dexter brake assemblies, 5200 capacity, with 5 bolt mounting flange. But the Nev-R-Adjust brakes on these axles should be the 12 x 2 inch brakes. We have several parts available including the following: Actuating Arm, Left Hand, # BP02-230 Actuating Arm, Right Hand, # BP02-240 Shoe Hold Down Spring, # BP06-090 Shoe Return Spring, # BP07-105 (works on left or right hand sides) Adjuster Plugs, # BP10-220 Adjuster # BP10-060 (these are regular adjusters so you may need to...
  view full answer...
• 4-Hole Spacing Measurements on Dexter 12 x 2 Inch Electric Trailer Brake Assemblies
  The mounting holes (4 hole pattern) on Dexter brake assembly, # 23-106-09, are 3.09 inches on center for the top two holes and 2.55 inches apart on center for the bottom 2 holes. Top to bottom they are 3.40 inches apart on center. The holes can accommodate a 7/16 inch bolt size. So it appears to be a match with the mounting plate you have. The matching left hand assembly is # 23-105-09.
  view full answer...
• Differences Between # 23-458 and #23-106-00 12 by 2 Inch Brake Assemblies
  Other than both brake assemblies being a 12x2 inch for a 6K axle, there are several differences between the two brake assemblies. Brake assemblies are either right or left side of the trailer specific. The # 23-458 is for the left side of a trailer while # 23-106-09 is for the right hand. The # 23-458 is a Nev-R-Adjust assembly that will self adjust each time the trailer is backed. The # 23-106-09 requires the brakes be manually adjusted. The # 23-106-09 is compatible with either the...
  view full answer...
• Trailer Brake Assembly Availability Measures 12 inches in Diameter with 4 Bolt Mounting Pattern
  We have the brake assemblies you are looking for. The only 6k rated 12 by 2 inch assemblies we offer that have the same unique 4 bolt mounting patter are the # 23-106-09 for the right hand side and part # 23-105-09 for the left hand side. This is for the non-standard Al-KO 4 bolt mounting flange that has a wider spacing for the top bolts than the bottom bolts.
  view full answer...
• Which Brake Drum is Used with Dexter # 23-105 and # 23-106 Brake Assemblies
  There are hubs/drums available for the # 23-105 and # 23-106 brake assemblies. You'll want to go with a 12 x 2 drum, and you'll want to choose one that has bearing compatible with your existing spindle and a lug and bolt circle pattern that's compatible with your existing wheels. If you'd care to reply with your inner and outer bearing reference numbers and the number of lugs and the bolt circle of your wheels, I'd be happy to make specific recommendations.
  view full answer...
• Electric Drum Brakes for 12,000-lb Big Tex Equipment Trailer
  To select new electric drum brakes for your Big Tex equipment trailer you'll want to confirm the trailer's GVWR or its axle capacity so you can choose brakes with the right amount of stopping power. For example, a 14K GVWR trailer such as their 20-foot Big Tex 14ET will use brakes for a 7K axle. For a trailer rated for 12K GVWR you'll use brakes for a 6K axle. You'll see all electric drum brakes on the page I linked for you. If you click on the 6000-lb axle rating you'll see brake sets...
  view full answer...
• Availability of 12 inch Trailer Brake Assembly with 4 Bolt Mounting Pattern
  It's a bit of a long shot but we do have one 12 inch brake assembly that uses a 4 bolt mounting style. It's the part # 23-105-09 and # 23-106-09. I attached a picture of the dimensions of the bolt pattern for you to check out. We have heard back from customers that this did fit older trailers so hopefully it fits yours.
  view full answer...

Do you have a question about this Accessories and Part?