Deka Heat Shrink Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 5

Ask the Experts about this Deka Accessories and Parts
Do you have a question about this Accessories and Part?

• How to Convert a 4-Way to a 7-Way on a 2017 Ford F-150
  
• If you are just needing a 7-Way to activate the lights on your trailer then you will simply need to use the Hopkins # 37185 that you referenced along with a No-Drill Mount Bracket # 18140 as depicted at the start of the attached installation video on a 2011 Ford F-150. For a fully functioning 7-Way that has power to the Brake Controller and 12V Power you will simply need some Deka Jacketed 2 Wire # 10-2-1 and Butt Connectors # DW05745-5. You will want to splice the Blue wire from the...
  view full answer...


• EOH Trailer Brakes Do Not Activate Immediately When Brake is Applied in 2016 Ram 3500
  
• There are a couple of things that come to mind with what you described. Either you have a short somewhere in your wiring or you are using a brake controller that is time delayed. A time delayed brake controller, like the Tekonsha PowerTrac # 39523, will apply the brakes at a predetermined strength shortly after the brake pedal is pressed in your 2016 Ram 3500. If you would rather have a brake controller that is proportional (applies the trailer brakes at the same time and with the same...
  view full answer...


• Installing a Brake Controller on a 2016 Honda Odyssey
  
• The parts needed and steps taken to install a brake controller, like the Tekonsha Prodigy P3 # 90195, on your 2016 Honda Odyssey will really depend on what they are wiring for your 7-Way. If they have wired all of the functions then you will simply need to connect the 4 wires from the pigtail on the P3 to the following functions: White - Ground (negative terminal on battery) Red - COLD side of Stop Light Switch (wire that gets hot only when brake pedal is pressed) Black - 12V Power...
  view full answer...


• Will Water Damage Magnets if Electric Brakes are Installed on Boat Trailer
  
• Electric brakes, like the Dexter Nev-R-Adjust Electric Trailer Brake Assembly # 23-458 that you referenced, are actually becoming more and more common on boat trailers. They used to not be so common because water and electricity don't play nice together, but if you unplug the trailer before backing it into the water you will be just fine. Any trailer components that are submerged under water will wear quicker than parts that are not, but if you make sure to hose down your boat trailer...
  view full answer...


• Installation of Brake Controller on 2017 Chevy 3500 to Replace Factory Integrated Brake Controller
  
• On your 2017 Chevy 3500 Duramax ltz, you can absolutely connect your Tekonsha Voyager Trailer Brake Controller # 39510 using the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers # 3016. This adapter plugs into the 4-pin connector in your vehicle's junction box. The box is located underneath the dash, to the left of the steering column, just above the carpeting. Because you have the integrated controller you will need to bypass it by cutting the blue wire on the # 3016...
  view full answer...


• Parts to Install Redarc Tow-Pro Elite Trailer Brake Controller 331-EBRH-ACCV2 in 2017 4Runner
  
• In your 2017 Toyota 4Runner installation of the Redarc Tow-Pro Elite Trailer Brake Controller # 331-EBRH-ACCV2 can use wiring adapter # 3041-P in conjunction with the parts included with the controller. This adapter has a white OEM connector to plug in at the under-dash brake controller port; you will cut off the other connector (the black plug) and then splice the four wires color for color to the harness included with the Tow Pro. You can use butt connectors # DW05745-5. The linked...
  view full answer...


• 7-Way Wiring Harness for 2015 Ford F-150
  
• There is a simple solution for you, but there is no trick to getting the wires of the # 118283 back out since the wires are different gauges due to the brown wire being for the right turn/stop functions and the blue wire being for the trailer brakes. What you can do is cut off the 7-way on the # 118283 and replace it with 7-way connector # HM47210 that has a pigtail; you'll only need butt connectors # DW05745-5 and # DW05744-5 to connect your splices.
  view full answer...


• Wire Size Butt Connectors is Needed to Connect Wiring for Electric Trailer Brakes
  
• Electric brakes, like part # 23-26-27, use 16 gauge wiring. However, we generally recommend using 10 gauge, like part # 10-2-1, to connect to the brakes because of how far the wiring generally has to be run. So you need to use butt connectors large enough for the 10 gauge wire, like part # DW05745-5. They'll still be able to be crimped down onto the smaller 16 gauge as well, especially since they're heat shrink. Between the two grease seals, parts # 58846 and # RG06-050, we prefer...
  view full answer...


• Installing a Trailer Battery Charge Line from Vehicle Trailer Connector
  
• To charge your trailer battery when you look at the 7-way trailer-side connector the 11 o'clock pin will mate up to your 12V signal from your vehicle. With most trailer connectors like # H20043 this will be the black wire. That black wire simply connects using 10 gauge butt connector like # DW05745-5 to 10 gauge wire sold by the foot # 10-1-1 which will connect to your trailer battery positive terminal. As you stated the negative terminal of the trailer battery will be connected to the...
  view full answer...


• Curt Adapter # C57674 and Tekonsha Prodigy P2 and P3 Operation
  
• If you have the Adapter 4 Pole to 7 Pole and 4 Pole w/Test Lamps # C57674 correctly installed then the 12V light will remain on as that is 12V of constant current going to the adapter. The way that the Tekonsha Prodigy P2 # 90885 and P3 # 90195 brake controllers work is that they have to have a trailer connected and there has to be movement for the inertia sensor to actually send output to the brake controller pin on your 7-Way when the brake pedal is pressed. The way to test one of...
  view full answer...


• Best Trailer Wiring Harness for a 2016 Toyota Sienna XLE
  
• I do have an option for you but the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # 118334 that you have will not work on your 2016 Toyota Sienna XLE. Instead, you will need to use the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # 118648. You can reference the attached install video if you need help with this. The Universal Installation Kit for Trailer Brake Controllers part # ETBC7 can however be transferred onto your new Sienna. In order...
  view full answer...


• Replacement Shear Pin for Ultra-Fab Ultra 3502 Powered Tongue Jack
  
• Powered trailer jacks allow use of a manual crank for emergency purposes (like a power loss) and some can be used with a drill attachment and a cordless drill. But an impact wrench puts too much stress into the mechanism and this type of tool should not be used on a jack. We do offer a replacement shear pin # UF38-751025 that fit jack model Ultra 3502 for serial numbers up to 010150 (which were made before 2010). My tech contact at Ultra-Fab thinks the self re-setting circuit breaker...
  view full answer...


• Parts Needed to Add Electric Drum Brakes to a 16' Dual Axle Trailer
  
• To install electric brakes on your trailer you need brake mounting flanges, brake assemblies, hub and drum assemblies, trailer wiring for the brakes, a breakaway kit, and a brake controller installed in your vehicle. You do want to install brakes on both sides of the axle(s) otherwise your trailer will pull to one side when your brakes are applied. We also recommend installing brakes on all of the axles that you have on your trailer. This helps to ensure that you have enough stopping...
  view full answer...


• Connecting separate reverse trailer lights using 5-pole wiring harness
  
• You are definitely on the right track. Start off by installing the Tow Ready 4 Pole to 5 Pole Trailer Wiring Adapter # 20036 on your tow vehicle with the Blue wire running to your reverse light signal. Once that is done I then recommend cutting off the 4-Way Flat connector on your trailer side and installing the Hopkins Endurance 5-Way Flat Trailer Connector # HM47910 using Butt Connectors # DW05744-10 to secure your connections (wires on the 5-Way are labeled). You can either run to...
  view full answer...


• Replacement 10-Inch Electric Drum Brakes for 1967 Airstream Travel Trailer
  
• Dexter Electric Drum Brake Set # 23-26-27 that you referenced does fit a 10 x 2-1/4-inch hub and it does use a 4-bolt pattern to mount to the brake flange on the spindle. The bolt pattern spacing is 2-7/8-inches apart on centers. The photo I linked for you will show you how to measure your hub dimensions to ensure they match the brakes. These manual adjust brakes are rated for a 3500-lb axle and they are compatible with trailer rims from 13- to 15-inches in diameter. The brakes are labeled...
  view full answer...


• Tekonsha Voyager Not Sending Power to the Trailer Brakes
  
• The Adapter # 3034-P that you referenced is the correct adapter to connect the Tekonsha Voyager # 39510 to your RV on a 2017 Ford E-450 Chassis. The part of your description that sounds like it is the problem is where you say the Black wire grounds into the Blue wire - this should not be the case and is most likely your issue. The Black, White, Blue, and Red wires from the Voyager should be connected to the following functions: Black - Battery for Power (20 Amp Circuit Breaker # PK54520...
  view full answer...


• Parts Needed to Install Prodigy P3 Trailer Brake Controller 90195 in 1993 Ford F-350
  
• I confirmed with Tekonsha that they do not offer a brake controller quick-connect harness for your 1993 Ford F-350 but you can still install their outstanding Prodigy P3 trailer brake controller # 90195. If you have a factory 7-way and the under-dash connection port you can make your own harness. You can use the pigtail plug that comes with the P3 along with Curt harness # C51312. Simply cut off the black plug (which would normally connect to a Curt brand brake controller) and splice...
  view full answer...


• Recommended Wire to Extend Length of Power Cable on Master Lock Electric Trailer Winch
  
• The Master Lock Electric Trailer Winch - 2,000 lbs # 2953AT comes with power cables that are 20 feet long and does not have other lengths available. If you wanted to extend that length 5-10 feet, you would need to use 12 gauge wire like # 12-2-1 sold by the foot and heat shrink butt connectors like # DW05745-5.
  view full answer...


• Correct Wiring Harness for the Curt Triflex Brake Controller
  
• The Curt Triflex brake controller # C51140 is an excellent choice when adding a brake controller to your vehicle. This brake controller activates trailer brakes in proportion to your vehicle's braking action, automatically adjusts trailer's braking based on deceleration of tow vehicle, and activates immediately with no pausing like with time-delayed brake controllers. But when trying to find the correct wiring harness to install it into a 2008 GMC Denali XL, the answer is the Universal...
  view full answer...


• Having to Frequently Replace Solenoid Valve for Titan Brake Actuators with Reverse Lockouts
  
• The first thing that comes to mind about the Replacement Solenoid # T4748800 needing to be replaced so often is that it could very well be a short in the wiring. I recommend checking the wiring on your trailer and your tow vehicle. You will want to check to see if there are any places that are corroded, have bent wires, or exposed wiring. If you find a place that looks like the wiring needs to be replaced, you can use 12 Gauge Wire, part # 12-1-1, and some Butt Connectors, part # DW05745-5,...
  view full answer...


• Recommendations for 7-Way Wiring Replacement on Gooseneck Trailer
  
• I've attached an article to help you with the wiring functions and common colors as well as pin placement. I've also attached some videos to assist with installation. For a long term solution, I recommend the Epicord 7-Way Molded Trailer Plug with Junction Box - 10' Long # 277-000141 and # 44-5310A ring terminals. This will make connections and trouble shooting easy as well as gives you the weather protection of having a wiring box versus heat shrink butt connectors. If you prefer...
  view full answer...


• Troubleshooting Newly Installed Brakes on 2000 Starcraft Tent Trailer
  
• If you tested the 7-Way at the rear of your tow vehicle then the next thing you will want to do is test the 7-Way on your trailer to make sure that power is getting to the brakes. Using a 12V battery, like the one from your tow vehicle, ground the negative terminal and then test the pin that corresponds to the brake controller pin on your tow vehicle side 7-Way. This is typically the pin in the 7 o'clock position on your trailer side connector (see attached picture). If your Dexter Electric...
  view full answer...


• Wiring for a 2017 Buick Encore and a 2007 Ural Retro to a 6-Pin Round Wiring Harness
  
• To add a 6-Pin round connector to your vehicle you will need an adapter in addition to the wiring harness that you referenced. For your 2017 Buick Encore the Curt T-Connector Wiring Harness # C56363 is where you'll need to start. The Next thing that you will need is the 4-Pole to 6-Pole Adapter # 30637. This will plug right into the 4-Way that you already have installed on your Encore. All you have to do at this point is add the extra wiring using 10 Gauge Wire # 10-1-1 in addition to...
  view full answer...


• Installing a 7-Way Connector at the Rear of a 5th Wheel Trailer with a 4-Pole Connector
  
• To get a functioning 7-Way at the rear of your 5th wheel trailer that has a 4-Pole you will want to install the Adapter 4-Pole to 7-Pole and 4-Pole # 37185 which can be mounted to your bumper using the No-Drill Mount Bracket # 18140. To get the 12V Power and Brake Controller signal from your Chevy Duramax you will then need to run Jacketed 2 Wire (Brake Wire) # 12-2-1 up to the 7-Way on your Duramax and splice it in. If Butt Connectors are needed use part # DW05745-5. If the Auxiliary pin...
  view full answer...


• Recommended Electric Brake Assemblies for Dual Axle Boat Trailer
  
• For your conversion to electric brakes I recommend the Electric Trailer Brake Kit - Self-Adjusting - 10" - Left and Right Hand Assemblies - 3,500 lbs # AKEBRK-35-SA which should be compatible with your current hub/drums. These assemblies need adjustment only at install and then will self-adjust as needed. I recommend using the # 10-2-1 wiring along with the Deka Heat Shrink Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 5 # DW05745-5 to seal your wiring connections....
  view full answer...


• Converting Factory 4-Way of 2017 Ford F-150 to 7-Way
  
• If you are just needing a 7-Way to activate the lights on your trailer then you will simply need to use the Hopkins # 37185 that you referenced along with a No-Drill Mount Bracket # 18140 as depicted at the start of the attached installation video on a 2011 Ford F-150. For a fully functioning 7-Way that has power to the Brake Controller and 12V Power you will simply need some Deka Jacketed 2 Wire # 10-2-1 and Butt Connectors # DW05745-5. You will want to splice the Blue wire from the...
  view full answer...


• Replacing 6-Pin Square Trailer Connector on Jayco Pop-Up Camper With a 4-Way Flat
  
• It sounds like you are replacing your older 6-pole wiring harness on your Jayco popup camper to a 4-flat connector like # HM48110. When you do this, you will have the black auxiliary wire and the blue brake wire remaining. You will no longer be able to use those functions, so those wires can just be taped up and stowed out of the way. The 4-Way trailer end functions are brown for running light circuit, white is the ground, green is right turn/stop, and yellow is left turn/stop. In regards...
  view full answer...


• Hopkins Reliance Brake Controller Installation in 1999 Ford F-250 Super Duty
  
• You can install your Hopkins Reliance hardwire-type trailer brake controller in your 1999 Ford F-250 by using harness part # HM47715. Just cut off the flat connector, splice the wires to your Reliance color for color using butt connectors like # DW05745-5 and plug it in to the under-dash port as shown in the linked video.
  view full answer...


• Installing Prodigy P3 Brake Controller on 2016 Forest River Forester on Sprinter 3500 Chassis
  
• I can help you find the parts you will need to install a Prodigy P3 Trailer Brake Controller # 90195 on your 2016 Forest River Forester on a Sprinter 3500 chassis. The P3 will need to be hardwired since there is not a custom wiring harness available for the 2016 Sprinter 3500. The parts you will need to install the brake controller are: Approximately 35 feet of duplex wire # 10-2-1 30 amp circuit breaker # 38630 A 5 pack of 10-12 heat shrink butt connectors # DW05745-5 2 yellow...
  view full answer...

Do you have a question about this Accessories and Part?