Deka Heat Shrink Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 10
(134 reviews)
Price: $12.16
In Stock
Deka Heat Shrink Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 10
Item # DW05745-10
Our Price: $12.16
Orders above $99 qualify for Free Shipping
In Stock
Need help with installation?
Locate installers near me- All Info
- Reviews (134)
- Q & A (170)
- Videos (1)
- Photos
- Why etrailer?
Deka Accessories and Parts - DW05745-10
- Wiring
- Wire Connectors
- Butt Connectors
- Deka
- 12-10 Gauge
This blue butt connector joins two lengths of 12-10 gauge wire. Insulated with heat-shrinkable nylon for adjustability and durability.
Features:
- Fits 12-10 gauge wire
- Heat-shrinkable nylon insulation allows for adjustability and provides durability
- Yellow
- Quantity: 10
05745 Deka Heat Shrink Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 10
Video of Deka Heat Shrink Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 10
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Review of Deka Wiring - 12-10 Gauge Butt Connectors - DW05745-10
Hello everybody, this is Jeff at etrailer.com. Today we take a look at the Deka yellow butt connectors for the 12 to 10 gauge size wire. And this is for a quantity of 10 connectors. Now these yellow butt connectors will join two lengths of 12 gauge or 10 gauge size wire and they'll insulate the connection with this heat shrinkable nylon for adjustability and durability. The yellow color will indicate the size wire that this connector will fit which is the 12 to 10 gauge size. And if you're not sure or remember which color fits what it is also stamped on the connector itself 12 dash 10 AWG.
Now to install these connector it's pretty simple. All you have to do is take the two wires you're wanting to connect. And at the end of it, strip off about a quarter of vincent quarter inch of the insulation, so you have a bare wire on each end and then you'll take the first wire and you'll stick it all the way into this side and push it until it goes as far as it will right in there's this metal casing in the center here, right in the middle there's a stopper. So when you put your wire in, it'll stop automatically. So just push it in all the way make sure your strip portion is under that metal casing and then take your crimper and just push down on that to crimp that wire to that side.
And then you'll do the same with the second wire. Take the strip den slide it all the way into it'll go no further make sure it's under the metal casing, crimp that end. And then once they're both crimp what you probably want to do is pull on the wires to make sure you got a good connection. Once that's good, then what you'll do is take a heat source, like a heat gun and then just apply heat up and down along this nylon here and it'll shrink over the insulation to completely seal around the connection and it prevents the elements from getting into that connection to cause a problem. Once that's all done, you're all set.
It's all ready to go. Now this part is for a quantity of 10 connectors. We do also sell it in a single pack which is part number DW Oh five seven four five dash one. And we also sell it in a five pack which is part number DW Oh five seven four five dash five but that should do it for the review on the Deka yellow butt connectors for the 12 to 10 gauge size wire for a quantity of 10..
Customer Reviews
Deka Heat Shrink Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 10 - DW05745-10
Average Customer Rating: 4.8 out of 5 stars (134 Customer Reviews)
This blue butt connector joins two lengths of 12-10 gauge wire. Insulated with heat-shrinkable nylon for adjustability and durability.
- DW05745-10
Wayne H - 07/11/2021
by: Wayne07/10/2020
Works good. Glad you recommended it.
Comments
Happy Happy Happy
Wayne H - 07/11/2021
- DW05745-10
by: Jeffrey02/26/2021
a must have to keep moisture out of the electrical brake connections. easy to crimp and seal, and one year later still keeping the connections dry. would definitely buy these again!
- DW05745-10
by: Fred04/01/2021
Worked well with my heat gun.
- DW05745-10
by: Brent06/24/2021
connectors worked fine, shrunk down well to seal the splice.
- DW05745-10
by: Jordan06/23/2020
100% will and have ready reccomended etrailer!! I called because I truthfully had no idea what all I needed so I was hoping an expert would help me. My hold time was long, the recording told me approximately how long and it was accurate. Also, it's three weeks before the Fourth of July and everyone wants something to get road worthy. No big deal. Once Geoffrey was on the phone I was absolutely blown away. He was patient, understood exactly what I was looking for (even though I didn't) and was incredibly helpful in the phone. He took his time to make sure we were going to have everything we needed to get the job done and get camping. He checked to make sure we were ordering the right size, even when our owners manual was super confusing he assisted in how to figure out exactly what we needed. Shipping... Wow. We placed our order and less than 13 hours later it had been picked, packaged and was on its way to a shipping facility. We received it 2 days after placing the order at 7pm. We are close, but still, that's incredible! Completely satisfied with every aspect of this experience.
- DW05745-10
by: David P04/02/2020
etrailer products and service are excellent! With their helpful videos and staff (plus a little help from Curt Manufacturing and our teardrop trailer manufacturer (CampInn)) I was able to install electric brakes on the trailer, and a controller in my vehicle by myself. I had never installed electric brakes before. Everything works perfectly!
- DW05745-10
by: Michael09/21/2019
The product arrived promptly as scheduled. The installation is simple: bolt the unit on the trailer frame with the supplied star washers and hook up the single power wire. The jack worked as advertised. Speed was typical for an electric jack. The quality of the jack could be better. The three housing screws were pushed thru the plastic cover. Repaired by removing the screws and reinstalling with small washers. The fuse holder, which is already installed on the power wire below the housing, is not water proof, which should be for an exterior application. Time will tell if the unit is better than my initial observations. Suggestion: the manual jack handle needs to be longer so it clears the top the of the propane tanks.
- DW05745-10
by: Duane07/29/2021
perfect fit
- DW05745-10
by: Vaughan07/04/2020
Great little kit! Easy installation. Bought the heat shrink butt connectors too.
- DW05745-10
by: Andre04/13/2021
great product. nice to have spare of those things when you need it.
- DW05745-10
by: Jeff12/01/2020
They worked great! I did not have hot air gun so I used a Bic lighter and it did the job.
- DW05745-10
by: Al S10/05/2016
I purchased a 5th wheel wiring harness and heat shrink butt connectors, for my 2015 GMC Sierra. I installed a tail gate light bar and did not want to cut the factory wiring. With the harness I was able to plug into the factory trailing plug and butt connect to the light bar, while still being able to use both the 7 blade and flat trailer connectors. It made for a easy and very clean connection. thank you to Steve and the E trailer web site for helping make this a easy job.
- DW05745-10
by: Malcolm11/08/2020
Makes connections a breeze and a good water tight seal. Happy
- DW05745-10
Phil T - 09/19/2016
by: Phil T.09/20/2015
Same exact brand that was on my trailer. Easy replacement of the brakes. A full $50 cheaper than the exact ones at the dealer where I purchased the trailer. Very happy.
Comments
Everything good. About to get the trailer inspected. Brakes are fine.
Phil T - 09/19/2016
- DW05745-10
Steve P - 11/09/2017
by: Steve P11/09/2016
The heat shrink butt connectors worked as advertised. Great Product.
Comments
All is well!
Steve P - 11/09/2017
- DW05745-10
by: Jon G.02/08/2017
Received all the parts to rebuild my travel trailer brakes in a short time. Everything from lug nuts, heat shrink splices, drums, bearings, seals, brake backing plates with complete brake assemblies. All in two boxes, albeit two heavy boxes... Total rebuild time from bare axles to tires on and torqued, about 2.5-3 hours. Everything I needed was there. Thanks to Sam G. for the great customer service.
- DW05745-10
by: Bruce04/29/2017
Order was complete and delivered in a timely manner. Only problem (minor) was the 7way pigtail was not wired to color code. Had to use test light to get 3 of the wires in correct location. Could be a problem if someone wasn't comfortable with ringing out wires.
- DW05745-10
by: Garnett08/23/2019
Ordered 3 parts: RM-156-25; RM-156-75 and DW05745-10. All received very quickly, as is the case when I purchase from etrailer. More importantly, I get a 'live person' when I call for assistance and the service rep. is always knowledgable ( not an answering service that "will have someone call back". Time was spent with me answering all my questions and providing suggestions and opinions when I as for them, related to my project. Great company, great service - keep up the great work!
- DW05745-10
by: Frank S12/18/2016
Great website, easy to locate and order the right parts, fabulous delivery speed. Love eTrailer.com's videos to guide you through the installation -- THANKS!! I agree with previous reviews that the packaging needs to improve. I had one brake assembly that had damage electric wires during shipping & I needed to repair. That is the only gripe I have. Other than that, THANKS!
- DW05745-10
by: Mark01/05/2021
Good connectors!
- DW05745-10
by: Rick01/27/2021
They hold tight and are weather proof too! I will buy again when needed.
- DW05745-10
by: David Weinstein01/07/2020
Performs exactly as described and would highly recommend them for someone looking to give their trailer protection while operating during freezing temperatures. Easy to install and wire!
- DW05745-10
by: Dean07/06/2016
I changed my trailer brakes to electric the NEV-ER-ADJUST brakes are good quality as is the heat shrink butt splices, 12-2 cable for the brakes. Glad I purchased new seals as there easy to damage when removing Very satisfied Thanks
- DW05745-10
by: Lance G09/26/2018
Works as advertised. Speedy delivery. Bought in conjunction with other items to rewire trailer.
- DW05745-10
by: Erich W.06/03/2019
I really like the idea of any outdoor wiring connector that has self-sealing heat shrink. I don’t agree with the suggestion of using a lighter to activate the heat shrink—use a proper heat gun designed for this.
25
134
Show More Reviews
Ask the Experts about this Deka Accessories and Parts
- How Many Sets of Electric Trailer Brakes For Tandem 3,500 lb Axles When Converting From HydraulicExcellent questions, and let's start with your query about having brakes on both axles. The answer is that you do indeed want to have brakes on both of your 3,500 lb tandem axles. The reason is because just one set of 3,500 lb brakes won't have the stopping power required for a trailer that weighs 5,000 or 6,000 lbs, and also just one set of brakes will also wear out very quickly as they'll be overworked for the load they are rated for. So for the best stopping power and safest way...
view full answer... - Adding a Trailer Battery to an Enclosed Cargo TrailerStart with mounting a battery. Since the trailer is enclosed, it would be a good idea to mount it on the trailer frame using a battery box like # 329-HM318BKS. Next, you will need to have the right kind of connectors on the truck and trailer. I would use a 7-Way RV style if you do not already have them on the truck and trailer. There is a 12 volt circuit on a 7-Way. You can run a wire from the 12 volt circuit on the trailer side connector to the positive battery terminal. The battery...
view full answer... - Connector Recommendation to Wire in Trailer BrakesYou can use butt connectors like the part # DW05745-10 or if you have a soldering iron you can solder the connections and then wrap the connections in electrical tape like part # DW04367. The butt connectors have a nylon insulation that you can apply a heat gun to which will also insulate the connection. If this is a boat trailer it's important to make the connections as waterproof as possible.
view full answer... - Is Jacketed 2-Wire 10 Gauge Brake Wire Wire Available In Different LengthsYes, you can get the 2-wire, 10 gauge brake wire in any length you want, as it is sold by the foot; what you need is the following: - Deka Jacketed 2-Wire, 10 Gauge Brake Wire - per Foot # 10-2-1 Just put however many feet of wire you are looking for in the "Quantity" box on the product page and you're set. If you need butt connectors as well, we have those with the Deka Heat Shrink Butt Connector - 12-10 Gauge - Qty. 5 # DW05745-5 or Qty. 10 # DW05745-10.
view full answer... - Ring Terminal Butt Connector Availability I really wish we did, but the largest ring terminal wire gauges we carry is 10 gauge like the part # 44-5310A for a 3/16 inch ring diameter, # 44-5356A for a 5/16 ring diamter, or a part # DW05705-1 for a 3/8 inner diameter. For an excellent airtight and waterproof sealant for your wiring connections I would recommend the Deka Self-Fusing Auto Tape # DW04367.
view full answer... - Brake Controller For 2018 VW Tiguan With Factory 4-Flat & Brakes For Trailer With 2,000 lb AxleWe can get you set up to tow your jet ski trailer and add electric brakes, but let's go ahead and start with the brake controller for your 2018 VW Tiguan. Since the vehicle already has a factory 4-flat, you would just need to add the 7-way and wiring along with the controller. You are on point with the wiring of your VW being finicky - that's a really good way to put it. The issue is that the brake light wire on a Tiguan is often inaccessible, or can be in different locations, if it...
view full answer... - Right Trailer Tail Light Is Not as Bright As LeftIt sounds like there may either be an issue with the ground, or on the power circuit of that particular wire. If the LED lights that you're using only have a single wire, they're going to ground via the mounting hardware so you'll want to verify that they are firmly attached to the trailer. If you've got a ground wire for all of the lights and other electrical functions on the trailer, you'll want to make sure that it is firmly connected to a paint and rust free spot on the trailer's frame....
view full answer... - Parts Needed to Add 5-Way Connector to Trailer and Tow VehicleOk, so we have exactly what you need, and since your trailer has surge brakes what you'll need for the trailer is a 5-way trailer connector. Since it sounds like you want to use those surge brakes you will also need to cut off your vehicle's 4-way and add a 5-way connector to the vehicle. So what you can add is the following: - Hopkins Endurance 5-Way Flat Trailer Wiring Kit - Vehicle and Trailer Ends # HM47890 To splice in the wires on these connectors you will need the Deka Heat...
view full answer... - Is It Safe To Add Electric Brakes To A Boat TrailerSure you can! A lot of boat trailer manufacturers put electric brakes on their trailers without any issues. We do recommend disconnecting the trailer wiring from the vehicle before backing into water just to err on the side of caution. In the past a lot of trailer companies only used hydraulic brake assemblies on boat trailers because water and electricity don't mix well. However, a lot of components to trailer brake installation have improved over the years such as the casing on wiring...
view full answer... - Installing Hopkins 4-Way/7-Way Wiring on a 2016 Chevy ColoradoYes, the Hopkins 7-Pole and 4-Pole Trailer Connector Sockets w/ Mounting Bracket and Wiring # HM40975-11998 is in stock. Installing this on a 2016 Chevy Colorado should take no time at all (maybe 20 minutes tops if you aren't familiar with it?) because all you have to do is replace the knockout plug in the bumper with this connector and then splice in the wiring harness to the OEM wiring on the driver's side of the bumper. Since this wiring will be out in the elements I recommend using...
view full answer...![Image 1 for]()
![Image 2 for]()
- Recommended Timbren Axle-Less System And Electric Trailer Brakes For M416 TrailerI would be happy to recommend the correct Timbren axle-less system and electric trailer brake setup for the M416 trailer you are rebuilding. Starting with the Timbren system, this is going to depend on how much weight you are planning carrying with the trailer. It looks like most of the M416 trailers weigh roughly 700lbs before accessories, so a 1200lb system should be enough which I recommend the Timbren Heavy-Duty Axle-Less Trailer Suspension # ASR1200S03 which is designed for wide...
view full answer... - Brake Controller Recommendation to Bypass 2018 GMC Sierra 3500 for EOH Style Trailer BrakesThe Dexter electric over hydraulic actuators don't have an adapter made for them that allows them to be used with integrated brake controllers like what your 2018 GMC Sierra 3500 has but even if they did I would not recommend that route as they don't work consistently. Instead you'd be best off with a new brake controller that has an EOH mode such as the P3 part # 90195 which we know will work flawlessly. You'll need the install harness # 3016 as well. First you will cut the blue wire...
view full answer... - Replacing Electric Brakes Shoes vs. Complete Brakes on 2005 Keystone CougarIf you measured the width of your trailer's electric drum brake shoes as 2-inches this should be fine as long as the brakes' diameter is 12-inches. Such 12 x 2-inch electric drum brakes are quite popular on RVs like your 2005 Keystone Cougar. This size electric drum brake is suitable for axles rated from 5200-lbs to 7000-lbs and these are what are typically supplied on travel trailers. Brake shoe kits for this 12 x 2 size brake are shown on the linked page. For example, for manual adjust...
view full answer... - Best Gooseneck Hitch for my 2020 Ram 1500We have the perfect solution. My recommendation is part # BWGNRK1319. This B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit is specifically designed for your truck. It has a 2 5/16" ball which is extremely common and the nice thing is that it is designed for both the 5.5' and 6.5' beds so regardless of what you've got it'll fit perfectly. It offers a 30,000 lb. gross trailer weight limit and a 7,500 lb. vertical load limit which is more than enough for what...
view full answer... - Troubleshooting Trailer Brake Lights and Turn Signals Not Working After Installing 7 Way on VehicleIf you've just installed a 7 way connector like the # ETBC7, you'll want to start by testing the plug on the vehicle using a circuit tester like the # PTW2979 to make sure that each pin is operating properly; you can refer to the photo attached or a helpful article that I've linked for information on testing the circuits. I would also recommend making sure that your ground wire on this harness is firmly grounded to a paint and rust free spot, as ground wires are the most common cause for...
view full answer...![Image 1 for]()
- Parts Needed to Wire Trailer With Electric BrakesTo add trailer brakes you'll want to start by adding a new 7 way trailer connector; for that I recommend using the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector # e99011, which will give you a 7 way and a way to install all of the wiring cleanly. You'll also need some 12 gauge wire, which is available by the foot with part # 12-1-1 and some butt connectors # DW05745-10 to make the connections to the wiring. Other than that, you'll just be making connections...
view full answer... - Converting Hydraulic Drum Brakes to Electric Brakes on Tandem 3,500 Lb Axle Boat TrailerYes, plenty of people choose to use electric brakes on their boat trailer because of the lower maintenance and cost as compared to hydraulic brakes. To replace your current hydraulic brakes I recommend our Electric Trailer Brake Kit # AKEBRK-35-SA. This includes both the right hand and left hand brake assemblies, mounting bolts and adjuster plugs. If you are unable to reuse your old nuts and lock washers, those are sold separately as part # BRKH10B. Since you were checking out hub...
view full answer... - Recommended Dimmable LED Strip Lights for 12 Foot Awning on 2013 Thor ACEI may have a solution for you, but there is not a product that we carry that is going to meet all of the specifications that you're seeking and the biggest issue will be the power cord, which you can work around with an extension cord. The other option would be wiring the light directly to a dimmer switch that can be installed right inside your RV door and routed to a 12v power source to allow you the best solution for this. I'll provide you with the parts for both options. If you want...
view full answer... - Can Electric Brakes Be Put on a Boat TrailerYes, electric brakes can be used on boat trailers. The brakes will not be damaged by going in and out of the water. Electric brakes are designed to hold up in all weather conditions because they have an E-coating that help prevent corrosion on most of the internal components and backing plate. For any of the wiring I recommend using Deka Heat Shrink Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 10 Item # DW05745-10 on any wires that are being spliced together. The heat...
view full answer... - Parts Needed to Rewire Trailer with 7-Way and New WiringWe offer handy junction box kits like # e99011 that let you install a new 7-way plug and make the connections for each circuit on the trailer. You will need ring terminals like # 44-5310A to make the connections in the junction box; use butt connectors like # DW05745-10 to splice in any new brake wiring like part # 10-2-1. This is double bonded 10 gauge wire that you can use for power and ground for the brake assemblies. Or if you planned on grounding the assemblies to the trailer frame...
view full answer...![Image 1 for]()
- Recommended 7 Way Wiring Harness for 2004 GMC Savana Cutaway Since you don't already have the factory wiring for a towing package on your 2004 GMC Savana Cutaway 3500, you'll first need to add a 4 way connector; to do this I recommend using the Tekonsha 4-pole Hardwire Kit with Circuit Tester # 18252 which will need to be hardwired into your vehicle electrical system. From there, to add the appropriate wiring for a brake controller, you need to add the Universal Installation Kit for Trailer Brake Controller # ETBC7 , which will put a 7 way connector...
view full answer... - Recommended Wire Connector Used To Attach Lights On Boat Trailer In order to join lights together on a boat trailer you'll want to use heat shrink butt connectors like part # DW05743-10, part # DW05744-10, and part # DW05745-10 as they keep out moisture which reduces the chance for corrosion that cause lighting issues. If you need to tie multiple wires together, you can do so using one of the larger butt connectors. In order to seal these connections you also need a heat gun, the Trades Pro Dual Range Heat Gun w/ Nozzles part # ALL836717. I have attached...
view full answer... - Replacement 7-Way Trailer Connector for 2015 Ford F-150It sounds like you have the factory 7-way on your 2015 Ford F-150 and only want to replace the cable that connects your 7-way socket like # HM40975 to the tow package wiring. If you are willing to hardwire in your socket you can get that with the 4' Pigtail Wiring Harness # PK11998. You would also need Heat Shrink Butt Connectors # DW05745-10. I have added a link to an install for you to check out. Otherwise, you can simply replace your entire 7-way with the Curt T-Connector Vehicle...
view full answer... - Best Wiring Options for Towing a 5th Wheel TrailerYou have a few options when it comes to 5th wheel wiring for your truck. Most trucks come with factory 7-way trailer connectors at the bumper. If your truck has a factory 7-way, then I recommend installing a 5th wheel wiring harness like the Hopkins Endurance 5th Wheel Harness, # 41157. In-bed harnesses provide a quick and easy connection point in the bed, so you don't have to modify the existing trailer harness to make it longer or use an extension. This harness has a 90-degree plug,...
view full answer... - Can Electric Trailer Brake Kit # AKEBRK-2 be Submerged in WaterThat is an excellent question and is asked more often than you think. Electric brakes like what come in the Electric Trailer Brake Kit # AKEBRK-2 can be submerged in water when you are loading/unloading your boat. Since water and electricity don't play nice together you do need to disconnect the wiring to your tow vehicle before backing into the water. When you make all your wiring connections I recommend using head shrink butt connectors like part # DW05745-10 or part # DW05744-10...
view full answer... - Recommended Wiring for Brake Controller On a 1995 Dodge Ram 1500To connect a brake controller to a 7-Way connector on your 1995 Dodge Ram 1500, I recommend the Universal Installation Kit for Trailer Brake Controller, # ETBC7. This will give you all the circuit breakers, wiring, and the 7-WAY connector. The only thing you will need to do is use butt connectors like # DW05745-10 to splice the 4 way round wiring into the 4 way flat wiring connections as the connector ends will need to be hardwired to each other. For a brake controller, I'd recommend...
view full answer... - Adding Interior and Exterior Work Lights to Livestock TrailerConsidering how you'll likely be using this, if you don't already have an auxilliary battery on your trailer, you'll need to add one. You'll want a 12v battery, which can be sourced from a number of different places, but I recommend something that can at least handle around 50 amp hours. This eliminates the chance that you run your vehicle battery down and get stranded somewhere, in addition to straining that battery and creating the need for replacing it much sooner than you normally would...
view full answer... - Locating a Front Mounted Trailer Hitch With High Tongue Weight Capacity on 2017 Ford F-350The EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2" # 306-X7904 is the highest rated front mounted hitch that is confirmed to fit your truck. My recommendation is to try and reposition the weight in your trailer to alleviate the tongue weight to get you within the range of this receiver. You may need to remove weight from the tongue and place it behind the rear axle to lessen the tongue weight as a front mounted hitch is not rated for weight distribution to displace...
view full answer... - Determining Fit and Installing Dexter Over-Under Kit on Wildwood X-Lite with 2-3/8" Axles As long as your Wildwood X-Lite Trailer is equipped with 2-3/8 inch diameter round axles and the leaf springs are currently mounted beneath them the Dexter Over-Under Conversion Kit # K71-384-00 will work perfectly. This will allow you to move the leaf springs to the top of the axle, lifting the trailer by the height of both the axle and leaf spring stack. All the necessary hardware for the axle flip is included but to re-connect your brake wires after you're finished you will need...
view full answer...
Do you have a question about this Accessories and Part?
Why etrailer.com?
At etrailer.com we guarantee:Highest quality accessories and parts for the best price.
Our Lowest Price Pledge ensures you will never overpay for the parts you need.Real product know-how.
We make sure that the products we sell are what we say they are, and that they work the way they are supposed to work. Get real advice from a real person who has the knowledge and expertise needed to solve your problem.Most detailed, accurate accessories and part information available.
Because we take providing accurate product information seriously, we take our own detailed product photos, demo videos and installation videos, as well as verify measurements, instructions, and vehicle fit information.Installations, made easy.
We love helping people and have the most highly-trained customer service, hands-on experience, step by step videos and installation instructions.Fast shipping.
Your order is automatically routed to get out of our warehouse and to your door as quickly as possible. Receive free shipping on orders over $99.Personalized service for life.
We provide one-on-one, personalized service from the ordering process through the life of your product.Trusted since 1946.
We've been serving customers since our parts store first opened in 1946 and continue to be recognized by our customers, our vendors and third parties for exceptional service.Returns Policy
Need to return an item? No problem. Please read our Returns Policy for more information.
Info for this part was:
Installed by:
Jeff D
Expert Research:
Jameson C
Updated by:
Adele M
Updated by:
Wilson B
Updated by:
Noah M
Written by:
Laura H
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 800-298-1624
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.