Menu Icon
fall hauling headquarters

Price: $0.32

In Stock

Ring Terminal -16-14 Gauge - 1/4" Ring ID - Qty. 1

Item # DW05702-1

lowest price pledge

Our Price: $0.32

Accessories and Parts

Orders above $99 qualify for Free Shipping

Shipping Weight: 0.01 lbs

Quantity: 

In Stock
DW05702-1 - 16-14 Gauge Deka Accessories and Parts
zoom in icon
zoom out icon
pop out icon replay 360 icon
horizontal rotate icon

Product Images

DW05702-1 - 16-14 Gauge Deka Accessories and Parts
Ring Terminal -16-14 Gauge - 1/4" Ring ID - Qty. 1 16-14 Gauge DW05702-1
DW05702-1 - 16-14 Gauge Deka Accessories and Parts

Videos


  • Wiring
  • Wire Connectors
  • Ring Terminals
  • Deka
  • 16-14 Gauge
  • 1/4 Inch
Call 800-298-8924 to order Deka accessories and parts part number DW05702-1 or order online at etrailer.com. Free expert support on all Deka products. Guaranteed Lowest Price and Fastest Shipping for Ring Terminal -16-14 Gauge - 1/4" Ring ID - Qty. 1. Accessories and Parts reviews from real customers.


  • All Info
  • Reviews (10)
  • Q & A (75)
  • Videos (1)
  • Photos
  • Why etrailer?

Deka Accessories and Parts - DW05702-1


Features:

Ring terminals are used for all types of electrical work where wires need fastening

  • For use with 16-14 gauge wire
  • Stud size: 1/4"
  • Vinyl insulation sleeve is blue

05702 Deka Wiring Ring Terminal - Blue




Video of Ring Terminal -16-14 Gauge - 1/4" Ring ID - Qty. 1


Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.




Video Transcript for Deka 16-14 Gauge Ring Terminal Review

Today on this old trailer, we're going to review an install. The Deka 14-16 gauge 1/4" ID ring terminal. Part number DW05702-1. The hole or 1/4" ring terminal is designed to fit over posts, such as on a battery or a junction box. These ring terminals are a super simple construction. We've got a metal ring that goes into the terminal inside the plastic sheathing.

We're looking inside the plastic portion of the terminal. You can see the metal piece inside. That's where we want to the feed the wire into and crimp down. We look here at the side profile of it. You can see there's just a little indention here, about half way, on the plastic.

That means we want to crimp down on the half closest to the large end of our ring terminal. That's where the solid portion of the metal on the inside of the plastic will be to crimp down the wire. Slide that ring terminal onto the wire. See, we've just a little bit peeking it out there Crimp it down. A nice solid connection.

That will do it for the review and install of the Deka 14-16 gauge ring terminal, part number DW05702-1. .


Customer Reviews

Ring Terminal -16-14 Gauge - 1/4" Ring ID - Qty. 1 - DW05702-1

Average Customer Rating:  4.7 out of 5 stars   (10 Customer Reviews)


- DW05702-1

by:


Best for non environmental exposure use. Use of sealed heat shrinkable terminals is recommended for maximum resistance to environmental exposure. 248040


Comments

This trailer is used in rustbelt America. Needed to replaced 1 of 2 terminals as it failed due to corrosion in the conductor crimp area. Replacement terminal was crimped, soldered, and an adhesive lined heat shrink tube was applied over the terminal crimp onto the cable insulation.

Jim - 05/02/2017

23553

- DW05702-1

by:


These worked fine. I used them to terminate LED lighting. No issues in the last year or so. 455178



- DW05702-1

by:


Used these for the junction box fit and work great. 61478



- DW05702-1

by:


Received on time, and as advertised. Great job!! 230244



- DW05702-1

by:


Product delivered within days and as or dered. 230552



- DW05702-1

by:


All the parts fit. Everything works we ll. 250197



- DW05702-1

by:


What can I say, its a ring terminal 246349



- DW05702-1

by:


Well made and as described. 353626



- DW05702-1

by:


Worked like it should 178169



- DW05702-1

by:


great price for items 60769


10
10

Ask the Experts about this Deka Accessories and Parts
Do you have a question about this Accessories and Part?


  • How to Rewire an Old Cattle Trailer
  • It sounds like you are on the right track to rewire your cattle trailer. You are correct about the wire colors on the 7-way connector that you purchased. The colors that you see on the 7-way connector are typical for RV style trailers rather than utility, cargo, or livestock style trailers. The black wire should be connected to the terminal in the 7-way connector labeled black. This is the terminal in the 11 oclock position when you are looking at the back of the trailer connector (see...
    view full answer...

  • Adapter and Re-Wiring Kit for Lance Truck Camper with Round Pin 7-Way Plug
  • The Pollak 7-Blade Plug to 7-Pole Round Trailer Connector Adapter # PK12727 should work fine to join your vehicle and Lance truck camper unless a previous owner modified it. You can try it and see or if you prefer a more permanent and predictable solution you might instead wire in a new 7-way blade style plug on the camper. A junction box/7-way plug kit like Epicord # 277-000141 or # ET7WK lets you convert the camper to match the 7-way RV blade type connector format. This avoids the...
    view full answer...

  • How to Install a Three Wire Trailer Light
  • It sounds like your current lights with 2 wires ground to the trailer by the mounting hardware. The One LED RV Passenger Tail Light # RVSTL0060 has three wires, the white wire is the ground, the black wire is the taillight and the green wire is for your stop lights and turn signals. To hook up your lights you will need to splice together the taillight and stop/turn wires. Then you will need to take the white wire and ground it to the trailer itself. To ground your wire you will want...
    view full answer...

  • Converting an Existing 9-pole Trailer Connection Plug to a 7-Way Connection
  • We do not supply a 9-pole to a 7-blade connector converter, but you can definitely convert your existing trailer connector to a 7-way blade connecter that will work with your truck. To do this you will need a replacement 7-blade connector like # PK12706. You will then disassemble the existing trailer connector and install the 7-way blade style connector. When you take apart the 9-pole connection point the functions should be labeled, and you will want to match up functions to the 7-way...
    view full answer...

  • Availability of Wiring Adapter to Convert 12-Pin NATO Trailer Connector to 7-Way Blade Style
  • We do not offer any adapters to convert a 12-pin military trailer connector to a 7-way RV-style plug like that on part # H20043 but we can help you gather the parts you'll need to wire in a new trailer plug to match that on your pickup. We can also offer you an easier alternative. To re-wire the trailer conector you'll need a wiring junction box # 38656, a trailer-side plug like the 4-foot # H20043 (or longer versions such as 6-foot # H20044 or 8-foot # H20046) and ring terminals like...
    view full answer...

  • Parts Needed to Re-Wire Car Hauler Trailer Lights and Brakes
  • We can help you with selecting parts to re-wire your trailer's lights and brakes. Trailer size affects the number and types of lights required to be DOT-compliant. I linked for you an article that covers the lighting requirements for trailers of various sizes. This will help you determine what is required for your specific trailer. For lighting you might want to consider one of our complete lighting kits. Kit # TL29BK uses standard incandescent light bulbs and kit # TLL9RK uses high-efficiency...
    view full answer...

  • What is Needed to Wire Replacement LED Trailer Lights for Separate Turn and Stop Light Functions
  • A standard 4-pole flat trailer connector carries brake light and turn signals on the same wires. Typically the yellow wire carries both left turn and stop light signals and the green wire carries both right turn and stop light signals. The brown wire carries the running light signal for both sides of the trailer and the white wire is the ground. Please refer to the photo attached. In order to separate the turn and brake signals so they can be sent to separate lights you will need a vehicle-to-vehicle...
    view full answer...

  • Wire Recommendation for Rewiring Utility Trailer with Brakes
  • For the brake circuit of your trailer you will want to run 10 gauge wire like our part # 10-1-1 which is sold by the foot and is standard copper primary wire. We use it all the time here on trailers and it works great. For bonded 14 gauge wire that has 4 wires bundled you would want the part # DW04923-1 which is also sold by the foot. A lot of times people use junction boxes like the part # 38656 to organize the wires on the trailer. Check out the install video I attached for more...
    view full answer...

  • Recommended Tail Light Converter For Trailer With Separate Wiring And LED Lights
  • I recommend the Vehicle to Vehicle Tail Light Converter, part # C56196 for your 2015 Highlander and trailer. The # 118158 will not work with the LED lights on your trailer. You will need to do some modifying of the trailer wiring to get this all to work. First, you will need to cut the trailer connector off and use a 4-way connector like part # HM48110. Connect the green wire to the green wire on the C56196 input, yellow wire to yellow input wire and white wire to white wire on the...
    view full answer...

  • Wiring Replacement 5-Pole Trailer Connector on 2012 Ranger Trailer
  • You can use a standard 5-pole trailer connector, you'll just need to wire it a certain way. The # HM47900 you referenced is the vehicle side connector, you need the trailer side connector like part # HM47910, which would wire as shown in the provided photo. The red wire you mention is for the reverse lockout on the trailer coupler, and is tied in with the reverse lamp circuit of the vehicle. Both brown wires would connect to the brown wire of the trailer connector. The yellow and green...
    view full answer...

  • How to Wire a Trailer for Tail Lights
  • First, lets make sure you have all of the parts you need to wire a trailer for lights. If you have an old trailer and want to replace everything, I recommend using a kit like our Optronics Tail Light Kit, # TL29BK and our trailer wiring installation kit # HM51020. We also have an LED kit, # TLL9RK. Step 1 - The trailer connector should extend 2 - 3 feet past the tongue. Attach the ground wire directly to the tongue of the trailer using a self tapping screw # 101131802 and a ring terminal...
    view full answer...

  • Recommended Surge Brake Actuator With Electric Lockout For Drum Brakes
  • We do have a surge actuator that has an electric lockout for drum brakes. I recommend the Titan Zinc-Plated Brake Actuator, part # T4339720. This actuator is adjustable to fit 1-7/8, 2, and 50-mm hitch balls and is a bolt-on for 3 inch wide trailer tongues. The breakaway kit is included with this actuator. If you have a 7-way connector on the back of your Expedition, you will need to change the trailer connector to match. I assume you have a 4-way connector. I recommend a 7-way connector...
    view full answer...

  • Recommended 7-Way Wiring Components for 2002 Coleman Pop-Up Camper
  • We do offer wiring adapters that allow connection of different formats of trailer wiring, but these are not the best long-term solution. Adapters add connection points, which bring the potential for problems, so the best option for trouble-free wiring is to swap out the 6-pin connector on the Coleman for a 7-way plug like # H20044. All you need is a wiring junction box like # 38656 and ring terminals for making the internal connections from the new plug and the trailer's existing wiring. You...
    view full answer...

  • Parts Needed to Completely Re-Wire 20-Foot Cattle Trailer with Light and Reflectors
  • The cost to re-wire your 20-foot cattle trailer depends on the type and number of lights you choose to install. How many lights you legally need depends on the width of the trailer. A good place to start your project is the linked article on trailer lighting. This explains the lighting requirements based on the trailer's length, width and weight. We offer basic light kits like # TL29BK that are a cost-effective all-in-one option. If your 20-foot trailer is less than 80-inches wide you...
    view full answer...

  • Installation Instructions for the Ventline Powered Vanair Trailer Roof Vent # VP-543SP
  • The installation instructions for the Ventline Vanair Trailer Roof Vent # VP-543SP that you referenced are included in the box and are as follows: 1.Cut a 6-1/4" diameter rough opening through roof. (You can use the smaller diameter of the ceiling garnish as a template.) 2.Remove the two screws from the roof cap and then take off the cap for access to the mounting holes. 3.Apply sealant to bottom of flange. Be sure to surround each screw hole. 4.Make electrical connections. 5.Insert...
    view full answer...

  • Parts Needed to Re-Wire 18 Foot Car Hauler Trailer with 7-Way Connector
  • To re-wire your 18 foot car hauler with electric brakes on one axle, I recommend using a wiring junction box like # 38656 in order to make the connections from the lights and brakes. Then for a 7-way trailer plug, you can use the Hopkins # H20046. This connector has an 8 foot lead. The shorter 6 foot # H20044 or 4 foot # H20043 trailer connectors are also available. I recommend using a circuit tester like # 40376 to determine the functions for any wires that are not known, as just using...
    view full answer...

  • New Trailer Wiring, Connector, Junction Box, and Battery Box for a Trailer
  • We have 7-wire strands but no 5-wire. What I recommend is to use duplex wire # 10-2-1, sold by the foot, for the brakes and bonded 4-wire, # 16-4B-1, also sold by the foot, for the lighting functions. For a junction box you can use # 38656. I have linked a couple of videos showing installations featuring these products for you. For a 7-Way trailer side connector you can use # H20046 with the wiring listed above. For the junction box you will also need some ring terminals. For the trailer...
    view full answer...

  • Installing New Trailer Lights and Wiring on a Horse Trailer
  • There isn't a kit available for what you are looking for, but you can still piece everything together. For grommets to use with the # ST45RB you would want the part # A45GB and then for a pigtail you would want the part # A45PB. Often times, people will run the wires from a 7-way such as yours to a junction box like part # 38656. From there, they will run the standard wire colors to the trailer lights, brakes and battery. I have attached a photo that shows how this setup works in...
    view full answer...

  • Recommended Wiring Harness for Rewiring a 26 Foot Gooseneck Stock Trailer
  • It sounds like you are wanting to rewire your gooseneck trailer with a 7-way connector. To do this I recommend the 7-way connector # H20046, the bonded 16 gauge 4 wire per foot # 16-4B-1 for the trailer and the 10 gauge jacketed wire # 10-2-1 for the brakes and ground. Often times, people will run the wires from a 7-way such as yours to a junction box like part # 38656. From there, they will run the standard wire colors to the trailer lights, brakes and battery. I have attached a...
    view full answer...

  • 7-Way and Light Kit Recommendation for Boat Trailer
  • The cleanest way to install the # HM20048 would be to use a junction box like part # 38656. The junction box is weatherproof to protect the wiring connections from the elements. You'd also need some ring terminals, one 10 gauge # DW05741-1 and four 14 gauge, part # DW05702-1. I've linked you to a video showing the junction box being installed. The part # TLL36RK is a submersible trailer wiring kit that would work well on your trailer as well.
    view full answer...

  • Adding Brakes to Acme Car Dolly
  • We don't offer parts specific for the Acme tow dolly, but we have the parts you'd need to add either electric or hydraulic drum brakes. I'm assuming your tow dolly doesn't currently have brakes, and that your current hubs use the # L44649 as the inner and outer wheel bearing. If that's the case, to add electric brakes, you'd need the following parts: # 8-257-5UC3-EZ hub drum for EZ lube spindle or # 8-257-5UC3 for standard spindles # 23-47 and # 23-48 electric brake assemblies # H20044...
    view full answer...

  • Preferred Method of Grounding Trailer Lighting Circuits
  • Running a direct ground up to the trailer tongue or junction box would certainly work, but the only time I'd see that as being necessary is if the lamps were connected to a non metallic structure or a metallic structure that wasn't directly connected to the trailer frame. If the lamps aren't connected to a metal structure in direct contact with the trailer frame, you can use a short length of # DW02359-1 wire with a # DW05702-1 ring terminal on each end to serve as a jumper wire that joins...
    view full answer...

  • Troubleshooting Trailer Tail Lights That Do Not Work After Installing Junction Box and New Lights
  • Whether the trailer wiring is the 4-pole flat format like # A35W42B or the 7-way format like # H20046 the tail and clearance light signals for the trailer are carried on one circuit, which means one specific wire and one specific pin. In 4-pole wiring that signal is carried on the brown wire, which is next to the white ground wire. In 7-way trailer wiring the running light signal is carried on the brown wire that connects to the pin at the 1-o-clock position as you look at the plug's contacts...
    view full answer...

  • Recommended Parts For Changing Surge Coupler To Electric Over Hydraulic Disc
  • When changing your trailer over you will need to do the complete change at one time since some of the parts are made for specific type brakes. I have attached a drawing that shows how the Titan BrakeRite EHB Electric-Hydraulic Actuator for Disc Brakes, part # T4813100 is attached. The # T4813100, has 5 wires that are blue, black, white, brown and purple. You will want to splice the blue wire from the adapter to the blue wire from the actuator. This allows the adapter to intercept the...
    view full answer...

  • Ring Terminal Sizes Needed for Installing Epicord 7-Way Plug with Junction Box 277-000141
  • The terminal posts in the Epicord 7-Way Molded Trailer Plug with Junction Box # 277-000141 are indeed a 3/16-inch diameter. You can use ring terminal # 44-5310A for connecting 10- and 12-gauge wires. For the lighter 14-gauge wiring use part # DW05702-1. You'll need a crimping tool like the one included in our Deluxe Trailer Wiring Kit # HM51020. I also recommend using dielectric grease # 11755 on those connections to protect them from moisture and corrosion.
    view full answer...

  • Troubleshooting Trailer Wiring Issues With 6 Wires Coming Out
  • It definitely sounds like someone has done some alternate wiring. I've attached an article on trailer wiring to help, but you will have to go off of the functions listed instead of the colors as the colors may have been changed around. It sounds like your running lights are connected to your trailer brake wire on the trailer. I recommend using a circuit tester with an incandescent light like # 3808 , to work through each function of your connection with your trailer. I've attached a...
    view full answer...

  • Replacing Horse Trailer Wiring
  • If you currently have a 6-way connector on your trailer, the 7-wire # DW04914-1 will be too large for your connector. In that case, you will want to use the 6-wire # DW04906-1. If your vehicle has a 7-way connector and you've been using an adapter, this is a great time to add a 7-way connector to your trailer to avoid needing the adapter. A 7-way connector is the more commonly found connector. You can use the 7-wire # DW04914-1 with a 7-way connector # PK12706, or a pre-wired connector...
    view full answer...

  • Wiring Needed to Rewire a Trailer for Lights and Electric Brakes
  • Both the # A40W5B and # W002290 have a blue wire that is only 5 feet long. Plus, the blue wire is only 18 gauge and 20 gauge, respectively. So these are not going to work for your application. What you're going to want to use is Bonded 4 Wire # 16-4B-1 which is sold by the foot. This will provide the four 16 gauge wires to run from the junction box, part # 277-000141, to your trailer's lights. Then for the brakes you will want a 10 gauge wire, # 10-1-1, which is also sold by the...
    view full answer...


Do you have a question about this Accessories and Part?




  • Why etrailer.com?

    At etrailer.com we guarantee:

  • Highest quality accessories and parts for the best price.

    Our Lowest Price Pledge ensures you will never overpay for the parts you need.
  • Real product know-how.

    We make sure that the products we sell are what we say they are, and that they work the way they are supposed to work. Get real advice from a real person who has the knowledge and expertise needed to solve your problem.
  • Most detailed, accurate accessories and part information available.

    Because we take providing accurate product information seriously, we take our own detailed product photos, demo videos and installation videos, as well as verify measurements, instructions, and vehicle fit information.
  • Installations, made easy.

    We love helping people and have the most highly-trained customer service, hands-on experience, step by step videos and installation instructions.
  • Fast shipping.

    Your order is automatically routed to get out of our warehouse and to your door as quickly as possible. Receive free shipping on orders over $99.
  • Personalized service for life.

    We provide one-on-one, personalized service from the ordering process through the life of your product.
  • Trusted since 1946.

    We've been serving customers since our parts store first opened in 1946 and continue to be recognized by our customers, our vendors and third parties for exceptional service.
  • Returns Policy

    Satisfaction Guarantee
    Need to return an item? No problem. Please read our Returns Policy for more information.

Info for this part was:

Photos by:
Theodore B
Expert Research:
Jameson C
Video Edited:
Jacob T

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.



Product Experts Available Now!

Call 800-298-8924


^
About Us
photos and videos
1,056,204

Original Photos & Videos

Produced to make sure you know what you are getting and you get exactly what you need.

installations
35,570

Installations Completed

To make sure products work and fit the way they are supposed to.

etrailer call center
2,476,511

Phone Calls & Emails Answered

1,125,924 phone calls and 1,350,587 emails to help find the right solution.

etrailer training
400+

Average Hours of Product Training

We get to know our products firsthand so experts can better help you.

etrailer service
71

Years of Quality Customer Service

Assisting our neighbors and customers, face to face at the counter.

etrailer experts
193,357

Pages of Expert Information

Created to make sure you have all the answers to your questions, from real experts.