1. Accessories and Parts
  2. Deka
  3. Wiring
  4. Wire
  5. Single Wire
  6. 16 Gauge
Primary Wire - 16-Gauge - White - per Foot

Primary Wire - 16-Gauge - White - per Foot

Item # DW02359-1
lowest price pledge
Our Price: $1.16
Accessories and Parts
Orders above $99 qualify for Free Shipping
Shipping Weight: 0.02 lbs
Quantity: 
In Stock, Ships Today
Accessories and Parts DW02359-1 - Wire - Deka
zoom in icon
zoom out icon
Comment field cannot be left empty.
Name field cannot be left empty.

Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.

Error submitting comment. Please try again momentarily.

Product Images

Copper primary wire can be used for a variety of trailer and automotive applications. This wire meets SAE J1128 specifications for the transportation industry. The general-purpose thermoplastic insulation resists automotive fluids. Call 800-298-8924 to order Deka accessories and parts part number DW02359-1 or order online at etrailer.com. Free expert support on all Deka products. Guaranteed Lowest Price and Fastest Shipping for Primary Wire - 16-Gauge - White - per Foot. Accessories and Parts reviews from real customers.
  • All Info
  • Reviews (18)
  • Q & A (57)
  • Photos
  • Why etrailer?

Deka Accessories and Parts - DW02359-1

  • Wiring
  • Wire
  • Deka
  • Single Wire
  • 16 Gauge

Copper primary wire can be used for a variety of trailer and automotive applications. This wire meets SAE J1128 specifications for the transportation industry. The general-purpose thermoplastic insulation resists automotive fluids.


Features:

  • For automotive, agricultural, marine and general use
  • General-purpose thermoplastic insulation resists corrosion from oil, gasoline, grease, acids and solvents


Specs:

  • Insulation rated to 176 F (80 C)
  • Meets SAE J1128 specifications
  • For 50 volts or less
  • Qty: 1'


02359 Redline Primary Wire - 16 Gauge White






Customer Reviews

Primary Wire - 16-Gauge - White - per Foot - DW02359-1

Average Customer Rating:  5.0 out of 5 stars   (18 Customer Reviews)

Copper primary wire can be used for a variety of trailer and automotive applications. This wire meets SAE J1128 specifications for the transportation industry. The general-purpose thermoplastic insulation resists automotive fluids.

- DW02359-1
by:

Fast shipping and great product 435050



- DW02359-1
by:

Great wire for rewiring a trailer and it's available in all the correct colors to match a 7 pin RV plug. Very high quality!! 758871



- DW02359-1
by:

All looks good and well made. 749415



- DW02359-1
by:

Shipped in a timely fashion and received . I will forward installation pictures on my ranger trail boat trailer when complete 746019



- DW02359-1
by:

Excellent customer service! 495966



- DW02359-1
by:

It arrived quickly and packaged nicely. Worked exactly for what I needed rewiring the lights on my trailer. 457599



- DW02359-1
by:

My order was correct and arrived in the time frame I expected. The items purchased worked as I hoped they would and I was safely towing my boat within three hours after receiving my order. Thanks E-trailer 320504



- DW02359-1
by:

Product arrived in perfect condition, well packed. It's always easy to deal with Etrailer.com and we have been repeat customers over and over! Product was installed on our 36ft gooseneck hauler and works great so far. 316446



- DW02359-1
by:

It's wire 265229



- DW02359-1
by:

Although I haven't utilized the products they appear what I ordered. The shipping was free, but took quite awhile to arrive... fortunately the electrical items to wire my trailer were not required in a real timely manner. I am excited to eventually get m;y lights and brakes wired on my custom trailer. I will befurther reviewing the helpful instructions when ready. Should be amazing, am excited. 264145


Comments
Great, no issues at all
Pete W - 06/26/2017

25454

- DW02359-1
by:

Very happy with the quality of this pro duct. 254516



- DW02359-1
by:

just what I needed and couldn't find in the quantity in my area. etrailer.com is great to do business with. order came quickly and all products have arrived as described and pictured. 242780



- DW02359-1
by:

You guys are great. Thank you for answering my questions and giving sound advice. I was very confident about my purchase after speaking with you. If only other businesses knew the value of good customer relations like you all do, the business world would be a much kinder place! Thank you so much! Jen 194283



- DW02359-1
by:

Great 192390



- DW02359-1
by:

It does the job. I used it as a ground and will use it to power a 12V power outlet. Good stuff. 180004



- DW02359-1
by:

was exactly what I was needing to rerun the brake wire. 148122



- DW02359-1
by:

Great price. 41859



- DW02359-1
by:

JUST THE RIGHT STUFF A++++++++++ 22901


18
18

Ask the Experts about this Deka Accessories and Parts

  • How to Create an Electrical Grounding Plate on DIY Truckbed Camper for Running Lights
    The short answer to your question is, no. You're going to be best served by running your ground wires together and grounding them at a single point on the trailer using a ring terminal like the # DW05705-1 and a junction box like # 38656. Since aluminum not is a great conductor of electricity, that wouldn't be a good choice to create your grounding plate- if you can ground it to steel instead that would be optimal. If you need wiring to run all these grounds together you can use 16 gauge...
    view full answer...
  • Why Do Trailer Lights Flicker When Hitting Bumps
    In order to fix the issue with your lights flickering you will want to pick a good spot on the trailer frame near the coupler and then run a ground wire from each of the lights as well as the trailer connector to this point. If you need to extend the wires you can use part # DW02359-1 and part # DW05744-5. Once you find a good ground point, sand the surface down, twist the wires together after you have removed part of the jacket, and then attach it to the sanded surface with part # DW05741-1...
    view full answer...
  • Hardware Needed to Install MaxxFan Deluxe Roof Vent # MA00-05100K
    The MaxxFan Deluxe Roof Vent w/ 12V Fan and Thermostat # MA00-05100K referenced in your question includes the white interior trim piece (garnish), insulated electrical connectors and the hardware needed for installation. The only thing you will need to add is some roof sealant # 0160297 and 16 gauge wire like # DW02359-1 if you don't already have it. The wire is sold by the foot so you can get exactly the length you need. This is a really nice roof vent with fan that will move air in...
    view full answer...
  • Wire Size Used to Install MaxxFan Deluxe Roof Vent w/12V Fan & Thermostat MA00-05100K
    The MaxxFan Deluxe Roof Vent w/ 12V Fan and Thermostat - Manual Lift - 10 Speed - White Item # MA00-05100K only requires 12 volt, 5 amp power to operate so based on this 12 gauge wire would be overkill but 16 gauge such as # DW02359-1 sold by the foot is more ideal.
    view full answer...
  • Can the MaxxFan Trailer Roof Vent # MA00-04000K be Left Open Without Rain Getting Inside
    The only way to operate the MaxxAir MaxxFan Trailer Roof Vent # MA00-04000K without rain getting inside is to also install the MaxxAir II Rain Cover # MA00-933072. If you are wanting a single-piece unit that includes a rain cover and utilizes a thermostat and a manual lift then the MaxxAir MaxxFan Trailer Roof Vent # MA00-06200K for Smoke or # MA00-05100K for White is exactly what you are looking for. All of these roof vents come with mounting hardware but you will also need some...
    view full answer...
  • Installation of MaxxFan Deluxe Roof Vent on 2013 Keystone Cougar
    The MaxxFan Deluxe Roof Vent # MA00-07500K will install in a standard 14" x 14" opening in your 2013 Keystone Cougar, and you can get power to the vent simply by running the black wire (the power wire) to the 12V power supply, as you can see in the accompanying cutout of the linked installation directions I added for you. If you need additional wire you can use 16 gauge wire # DW02359-1. This vent does come with all the necessary hardware for installation though you are going to need...
    view full answer...
  • Availability of Black and White 16 Gauge Wire
    In 16 gauge wire we only carry two colors by the foot. We have the black wire part # 16-1-1 or we have the white part # DW02359-1. In 10 gauge we only have the wire in red like part # DW02508-1 or blue like part # 10-1-1 but I think what you'd really be best served with is the 7-way upgrade kit part # e99011 which comes with a 7-way and junction box and then for the wiring to run from the box to the trailer wiring you'd want the # DW04914-1 which is sold by the foot and uses the standard...
    view full answer...
  • Recommended Wire For MaxxTow Off-Road Lights
    We do not have a specific wire harness for the MaxxTow Off-Road Lights, part # MT70882 because it is universal and can be installed on so many different items. It is a 2-wire design so all you need is power for the red wire and the black wire is your ground. You can use part # 16-1-1 and # DW02359-1 that is jacketed Black and White wire. It is sold by the foot so you will need to keep that in mind when ordering. For butt connectors I recommend part # 05731-5. You can also install...
    view full answer...
  • Converting a 3-Way Northland Truck Camper Wiring Harness to a 4-Way Flat
    What you can do is to use the Quick FixTM 4 Pole Flat Car and Trailer Ends, # 48195, and not use one of the pins since you only have three wires that need to be connected. You can then use the wire you need inside of them as needed. The wires that run to the battery are most likely 10 gauge like # 10-1-1. The remaining wire is probably a 16 gauge like # DW02359-1.
    view full answer...
  • Installation of MaxxAir MaxxFan Trailer Roof Vent
    While we would not have any way to know for sure it is unlikely there is going to be wiring run. In order to install the MaxxAir MaxxFan Trailer Roof Vent # MA00-06200K you would need to use Primary Wire - 16 Gauge # DW02359-1 to run wire to a 12V power source. This vent is designed to fit standard RV roof openings of 14” x 14” and a minimum roof thickness of 1-1/8” to a maximum of 6-1/2”; it will also require the use of Sealant # 0160297 to ensure a tight bond between the flange...
    view full answer...
  • How to Connect a Surge Brake Actuator to Activate the Reverse Lockout Function
    There are 2 wires that are coming out of the actuator in the Titan Disc Brake Kit # T4843300. You will want to connect one to the 5-Pole connector on your trailer and ground the other one using a Ring Terminal # DW05737-1; it doesn't matter which wire is used for which purpose. If you only have a 4-Pole connector on your trailer then I recommend using the Hopkins Endurance 5-Way Flat Trailer Connector # HM47910 instead. You will want to cut off your current 4-Pole and use Butt Connectors...
    view full answer...
  • Installation Instructions for the Ventline Powered Vanair Trailer Roof Vent # VP-543SP
    The installation instructions for the Ventline Vanair Trailer Roof Vent # VP-543SP that you referenced are included in the box and are as follows: 1.Cut a 6-1/4" diameter rough opening through roof. (You can use the smaller diameter of the ceiling garnish as a template.) 2.Remove the two screws from the roof cap and then take off the cap for access to the mounting holes. 3.Apply sealant to bottom of flange. Be sure to surround each screw hole. 4.Make electrical connections. 5.Insert...
    view full answer...
  • Recommended Best Light for Bright Utility Reverse Light for Utility Trailer
    For the best and brightest utility light, I would recommend the Vision X # XIL-ST12. It's 12" long x 1" wide x 1/2" deep and by far the brightest strip light with an effective lumen output of 300. When you go to wire up the utility lights on your trailer the best way is to run the power wire to each light and then run the ground to both as well. You'd simply run some # DW02359-1 16 gauge wire (sold by the foot) up to the front of the trailer, and tie into a switch. It's important...
    view full answer...
  • How to Install a Ventline Ventadome Roof Vent with 12 Inch Fan Powered Lift
    You can utilize a power wall remote switch # VC0533-03-A or # VC0533-02-A (black or white). A rocker switch # BL0108-00 will work and you will need 2 of them. The installation kit # 344270KITW will come with screws, tape, and sealant. You will also need primary 16 gauge wire # DW02359-1 as well as a ceiling garnish # VA0445-35 I have attached a picture of wiring instructions for you as well. Installation Instructions for the Ventline Ventadome Roof Vent # V2119-601-00. 1.Mark...
    view full answer...
  • Wiring and Switch Recommendations for MaxxTow Off-Road Lights # MT70882
    MaxxTow Off-Road Lights # MT70882 do not come with a switch or wiring because of its universal design. The lights have 2 wires. The red wire is the power wire and the black wire is the ground. For wire you can use # DW02359-1. It is sold by the foot so you will need to keep that in mind when ordering. For butt connectors I recommend part # DW05744-10. For a switch you can use a toggle switch such as # PK34513 or part # PK34310.
    view full answer...
  • Recommended Wire Gauge Needed to Extend Vent Fan Power Wire to Charge Controller
    To wire up your Ventline vent # VP-543SP the correct gauge wire needed is a 16 gauge like # DW02359-1. You will also want to use the 16 gauge buttconnectors like # DW05714 to connect the two wires. You definitely want this to be connected to a fused power source so if your charge controller isn't fused then on the 16 gauge wire you would want to wire in a 5amp fuse to protect the unit.
    view full answer...
  • Recommended Roof Vent for 2013 Ford Transit Connect
    I have a couple of different options for a roof vent on your 2013 Ford Transit. A lot of our roof vents sit around the same height, so it really just depends on what kind of style you would like to have. The Ventline Ventadome # V2110SP-24 is a good option because it only adds 2 inches in height when closed, and 11 inches in height when opened. You can also make sure that your roof vent matches the rest of your Transit by painting it. This manual vent doesn't include a fan and requires...
    view full answer...
  • Preferred Method of Grounding Trailer Lighting Circuits
    Running a direct ground up to the trailer tongue or junction box would certainly work, but the only time I'd see that as being necessary is if the lamps were connected to a non metallic structure or a metallic structure that wasn't directly connected to the trailer frame. If the lamps aren't connected to a metal structure in direct contact with the trailer frame, you can use a short length of # DW02359-1 wire with a # DW05702-1 ring terminal on each end to serve as a jumper wire that joins...
    view full answer...
  • Tekonsha Prodigy RF Turns Off and On When Turn Signal is Used
    I spoke with my contact at Tekonsha and the problem that you are experiencing is most likely caused by faulty wiring on your trailer. The (discontinued) Tekonsha Prodigy RF 90250 works by activating the brakes when there is a signal on both the Left Turn/Brake and Right Turn/Brake wiring functions. If your turn signal is causing the RF to act up then you will want to do some tests to see where the wiring problem is. Check to make sure that the ground on both your tow vehicle and...
    view full answer...
  • Installing Trailer Lights on a Non-Metal Frame
    Good news, I can help. You can simply connect an extension wire like part # DW02359-1 from the ground wire on the # STL8RB light to the trailer's main ground connection or to the metal trailer tongue. We do have a trailer wiring installation kit # HM51020 that will make installing the Hopkins # HM48240 harness to the trailer a little easier. I have linked all the above mentioned parts as well as a Help Article for your viewing and purchasing convenience.
    view full answer...
  • Can Bargman Tail Lights with Reverse Lights be Added to a Trailer that Does Not have Reverse Lights
    Bargman Surface Mount Tail Light # 30-92-002 mounts to a flat surface so technically it can be installed on any trailer. To determine if they are a direct fit to your 2015 Keystone Hideout I would have to know which lights it has now or the overall dimensions of the lights. Trailers rarely have reverse lights and to add them is going to require hardwiring at least 1 wire and changing the connector (if the current connector is a 4-Way). Or there are connectors you can get that also have...
    view full answer...
  • What Gauge Wiring For 16 Foot Gooseneck Horse Trailer?
    Using the 6-Way Molded Connector w/ Cable - Trailer End # 50-61-104 and a junction box like # 38656 is a wise start. I recommend using the Ring Terminal - 12-10 Gauge Wire - 3/16" Ring ID # 44-5310A for this fit. For your brake wiring, I recommend using 10 gauge wire # 10-2-1. For your tail lights, running lights and interior lights you can use 16 gauge wire like the Bonded 4 Wire - per foot # 16-4B-1 or single wire # DW02359-1.
    view full answer...
  • Grounding Trailer Lights That are Mounted to Wood Rather than Metal
    If the lights you are using have wires coming out of the back like the Optronics Camping Travel Trailer Stop, Turn, Tail and Back-Up Light, part # RVST56, then you can simply connect an extension wire like part # DW02359-1 from the ground wire on the light to the trailer frame and ground the white wire from your trailer connector to the trailer tongue. If the lights you are using ground through the mounting hardware, then you can simply run a jumper wire from the post on the light that...
    view full answer...
  • Powering Reverse Lights on Pop-Up Camper with 6-Way Trailer Connector
    The idea you propose, using a switch to power your reverse lights using the 12-volt accessory circuit off of your 6-way trailer connector would most likely work. I would first recommend you find out where that 12-volt circuit terminates on the trailer. Some pop-up campers have a battery for interior lights. The 12-volt accessory circuit keeps that battery maintained. Had you not already purchased the OEM 6-way replacement connector, I would have recommended going with the 7-way replacement,...
    view full answer...
  • Availability of Replacement Parts for Ventline Rounded Dome Trailer Roof Vent
    The Ventline product you reviewed, part # V2092SP-28, is a complete vent assembly intended for a rough roof opening of 14-1/4 x 14-1/4 inches. It consists of a wedge-shaped white plastic dome attached to a galvanized steel frame with hand-crank assembly, a removable screen, and a white plastic 2-1/8-inch-deep garnish (interior trim ring). Please note that this part requires an installation kit, part # 344270KITW, which consists of mounting hardware and a urethane caulk sealer. If your...
    view full answer...
  • Switch and Wiring Recommendation for Use with MaxxTow Off-Road Lights # MT70882
    MaxxTow Off-Road Lights # MT70882 do not come with a switch or wiring because of its universal design. The lights have 2 wires. The red wire is the power wire and the black wire is the ground. For wire you can use # DW02359-1. It is sold by the foot so you will need to keep that in mind when ordering. For butt connectors I recommend part # DW05744-10. For a switch you can use a toggle switch such as # PK34513 or part # PK34310.
    view full answer...
  • Is Wiring Included in Bulldog Winch Dual USB Port BDW20287
    The Bulldog Winch Dual USB Port # BDW20287 does not include the wire to connect it to your trailer's electrical system but you can use 18-gauge wire in a run as long as 50-feet. If you need a longer wire run, or if you just want to ensure full current capacity, then use 16-gauge wire. For 16-gauge black wire use part # 16-1-1; for white use part # DW02359-1. Both are sold by the foot.
    view full answer...
  • Installation of Reverse Light Circuit on Trailer with 2013 Jeep Grand Cherokee with 4-way Connector
    It sounds like you need the # 37185 wiring harness. This connector will adapt your 4-way wiring to a 7-way connection and the purple wire will connect to your reverse light connection on your vehicle to transmit the signal onto your trailer. You will need some 10 gauge wire to splice in this connection # DW02359-1 and # SWC502905-1. For any unused wires you will want to cap them off or secure them with electrical tape and zip tie them out of the way. Have a helper place the transmission...
    view full answer...

Do you have a question about this Accessories and Part?




  • Why etrailer.com?

    At etrailer.com we guarantee:
  • Highest quality accessories and parts for the best price.

    Our Lowest Price Pledge ensures you will never overpay for the parts you need.
  • Real product know-how.

    We make sure that the products we sell are what we say they are, and that they work the way they are supposed to work. Get real advice from a real person who has the knowledge and expertise needed to solve your problem.
  • Most detailed, accurate accessories and part information available.

    Because we take providing accurate product information seriously, we take our own detailed product photos, demo videos and installation videos, as well as verify measurements, instructions, and vehicle fit information.
  • Installations, made easy.

    We love helping people and have the most highly-trained customer service, hands-on experience, step by step videos and installation instructions.
  • Fast shipping.

    Your order is automatically routed to get out of our warehouse and to your door as quickly as possible. Receive free shipping on orders over $99.
  • Personalized service for life.

    We provide one-on-one, personalized service from the ordering process through the life of your product.
  • Trusted since 1946.

    We've been serving customers since our parts store first opened in 1946 and continue to be recognized by our customers, our vendors and third parties for exceptional service.
  • Returns Policy

    Need to return an item? No problem. Please read our Returns Policy for more information.

Info for this part was:

Written by:
Lindsey S
Edited By:
Leah B

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.