Curt Spring Bar Retainer Package for Round Bar Style Weight Distribution

Ask the Experts about this Curt Accessories and Parts

• Recommended Round Bar Retainer Clips for Weight Distribution Head
  Reese does not offer the spring bar retainer clips like you have referenced. The really good news is that you can use either the Replacement Spring-Bar Release Clip # FA94-02-1059 or Curt # 17109. These clips will work as replacements for the hitch you have pictured.
  view full answer...
• What is the Length and Diameter of the Pins in the CURT Spring Bar Retainer Package
  I went out to the warehouse and pulled a CURT Spring Bar Retainer Package, # 17109, to measure the pins. I used a set of digital dial calipers to take the measurements. Each pin is 0.724 inches long and has a diameter of 0.313 inches. The kit is designed for CURT Round Bar Weight Distribution systems.
  view full answer...
• Installing Curt Spring Bar Retainer Package # 17109
  When installing the included rivets from the Curt Spring Bar Retainer Package # 17109 referenced in your question, you will not need any special tools to insert the new rivet/set key. The new set key (which likely has a slightly different design than the true rivet that is currently used on the system head), will simply set into place when inserted into the hole. You should not even need a hammer to get it seated into position. When installing the spring clip, you will first put both...
  view full answer...
• Removing Rivets to Install Curt Spring Bar Retainer Package # 17109
  You will need a chisel to remove the head of the old rivet and a pin punch to remove the remaining shank so that you can install the part # 17109 that you referenced.
  view full answer...
• How to Install Curt Weight Distribution Spring Bar Retainer Package 17109
  Curt Spring Bar Retainer Package # 17109 for round bar weight distribution systems like # C17002 includes clips, locking pins and rivets; and the rivets do resemble screws when they are installed. The old ones need to be drilled out in order to install the replacement parts in the kit unless you can get a grip on them with pliers. They usually can be pulled out.
  view full answer...
• Direction of Pins on Curt Round Spring Bar Retainer Package
  I believe you are simply asking the direction of how the clips on the Curt Spring Bar Retainer Package for Round Bar Style Weight Distribution # 17109 go. If you take a look at the accompanying photo of them on a Curt weight distribution head you can see the direction the pins will be oriented.
  view full answer...
• What are the Measurements of Locking Pins in Curt Spring Bar Retainer Package 17109
  The locking pins in Curt Spring Bar Retainer Package for Round Bar Style Weight Distribution Item # 17109 are 0.72 inches long with a diameter of 0.313 inches. I have included a picture showing this and other measurements for you.
  view full answer...
• Replacement Spring Bar Retainer Clips and Pins for Curt Weight Distribution System
  The weight distribution head you have pictured look s like the Curt round bar head. If that's what you have the Spring Bar Retainer Package # 17109 is what you're looking for.
  view full answer...
• Removing and Replacing Spring Bar Retaining Clips of Curt Weight Distribution System
  To remove the retaining clips # 17109 on a Curt weight distribution system with round bars you would first remove the bottom screws holding them on. Then you would push the clips up so the wider part of the hole can slip off the top pin. The top pin fits into the groove in the spring bar when inserted into the head. If the pins are also being replaced pull out the old ones and then insert the new ones. To install the clips you would reverse the above process. Check out the attached...
  view full answer...
• How to Remove and Reinstall the Retaining Clips on a Curt Round Bar Weight Distribution System
  To remove the retaining clips # 17109 on a Curt weight distribution system with round bars you would first remove the bottom screws holding them on. Then you would push the clips up so the wider part of the hole can slip off the top pin. The top pin fits into the groove in the spring bar when inserted into the head. If the pins are also being replaced pull out the old ones and then insert the new ones. To install the clips you would reverse the above process. Check out the attached...
  view full answer...
• How to Remove and Reinstall the Retaining Clips on a Curt Round Bar Weight Distribution System
  To remove the retaining clips # 17109 on a Curt weight distribution system with round bars you would first remove the bottom screws holding them on. Then you would push the clips up so the wider part of the hole can slip off the top pin. The top pin fits into the groove in the spring bar when inserted into the head. If the pins are also being replaced pull out the old ones and then insert the new ones. To install the clips you would reverse the above process.
  view full answer...
• Replacement Spring Bar Retainer Kit for Curt Round Bar Weight Distribution Systems
  Yes, the Curt spring bar retainer package # 17109 will fit Curt round bar weight distribution systems such as 17002 that you have. The kit comes with e2 clips, 2 pins, and 2 rivets. Once installed it would look like head # C17107.
  view full answer...
• Replacement Clips for Weight Distribution System
  We have a few different clip options that are possible fits for your Weight Distribution (WD) system. Fastway WD - FA94-02-1059 Curt WD - 17109 From the picture that you sent me, I believe that the Curt clips # 17109 are the correct replacement clips for you.
  view full answer...
• How to Remove and Reinstall the Retaining Clips on a Curt Round Bar Weight Distribution System
  To remove the retaining clips # 17109 on a Curt weight distribution system with round bars you would first remove the bottom screws holding them on. Then you would push the clips up so the wider part of the hole can slip off the top pin. The top pin fits into the groove in the spring bar when inserted into the head. If the pins are also being replaced pull out the old ones and then insert the new ones. To install the clips you would reverse the above process.
  view full answer...
• Replacement Parts for Curt Weight Distribution System
  We do have a large selection of replacement parts available for Curt weight distribution systems, which I have linked for you below. It sounds like you might be needing the Spring Bar Retainers # 17109, which are designed for the Curt Round Bar systems. This kit includes two clips, two locking pins, and two rivets. I am not sure what you mean by the L shaped keeper, but we do also have the Replacement Lift Bracket # C17008, which is what mounts to the trailer frame and provides...
  view full answer...
• Replacement Retaining Clips Needed for the Curt # C17107 Weight Distribution Head
  I believe the silver piece you are talking about on the Curt # C17107 are the retainer clips which can be replaced with part # 17109 on our site. To remove your current clips you first need to remove the bottom screws holding them in and then push the clips up to the wide part of the hole can slip off of the pin (see attached photo). Simply reverse what you just did for the install.
  view full answer...
• Replacement Parts for Curt 10K MV Weight Distribution System
  The Curt MV Weight Distribution System part # C17062 is composed of the following parts: Curt Spring Bar Retainer Package for Round Bar Style Weight Distribution part # 17109 2-5/16" Hitch Ball - 1-1/4" Diameter x 2-5/8" Long Shank - Chrome - 10,000 lbs part # A-6 Replacement Lift Handle for Curt Weight Distribution Systems part # C17112 Replacement Lift Bracket for Curt Weight Distribution Systems part # C17008 Replacement Bolt Kit for Curt MV Weight Distribution Systems part #...
  view full answer...
• Replacement Retainer Clips for Round Bar Weight Distribution System
  It sounds as if you're needing the spring bar retainer clip kit. If you have the Curt or a Reese Round Bar system, use # 17109 which includes 2 clips, 2 lock pins and two drive-in rivets. The exact kit needed will depend on which manufacturer's weight distribution kit you have. For a Fastway e2, use part # FA94-02-1059 which inlcudes 1 clip, 1 pin and one rivet.
  view full answer...
• Replacement Pins for Curt Round Bar Weight Distribution System
  If you are talking about the pins for the spring bar retainer clips there is a kit you can use # 17109 which includes the pins, clips, and retaining screws. If none of these are the parts you are looking for then I have included a link to all of the Curt weight distribution parts that we have.
  view full answer...
• Replacement Spring Bar Retainer Clips for Weight Distribution System
  It sounds like you might need the clips that hold your round spring bars in the head unit. If you have a Fastway e2 system then their Replacement Spring-Bar Release Clips # FA94-02-1059 are the correct part. If you have a Curt system use their part # 17109. Yes, you can certainly send us photos of your weight distribution hitch. You can just reply to this email with your photos and hitch brand information.
  view full answer...
• Replacement Part For Curt Trunnion Style Weight Distribution
  I'm not sure what L-clips you are describing in the Curt Weight Distribution System, but hopefully one of these replacement parts will be what you were describing. We have the Replacement Hook Up Brackets for Curt Weight Distribution Systems # C17208, the Chain Hangers for Curt Weight Distribution Systems - Clamp On # C17003 or bolt on # C17005. We have the Replacement Lift Bracket for Curt Weight Distribution Systems # C17008. We also have the Curt Spring Bar Retainer Package...
  view full answer...

Do you have a question about this Accessories and Part?