Gen-Y Hitch Aluminum Loading Ramp Set - 96" Long x 15" Wide - 10,000 lbs

See what our Experts say about this Gen-Y Hitch Car Ramps

• Weight Capacity of Gen-Y Aluminum Loading Ramp Set 325-GH-R96
  The USA-made Gen-Y Aluminum Loading Ramps # 325-GH-R96 have a combined capacity of 10,000-lbs, well above your actual load of 7900-lbs, so I would expect no issues with loading your Excursion. The ramps have 20% more capacity than you need and I would consider that a very reasonable safety margin. Each ramp weighs about 50-lbs despite their lightweight aluminum construction so that suggests that a lot of material is used in their fabrication. I cannot comment on your original ramps since...
  view full answer...
• Gen-Y Aluminum Ramp Set-96 long X 15 Wide-10,000 lbs Material and Wall Thickness
  I checked with Gen-Y and they informed me that their ramp set part # 325-GH-R96 is made from a double hollow tube, 3” x 5”, with a wall thickness of .125 A6063 alloy.
  view full answer...
• Ramp Recommendation for Loading Bobcat 331 Onto Trailer
  For a Bobcat 331 that weighs up to 7,500 lbs I'd recommend the 10k ramps part # 325-GH-R96 that you referenced which are 96 inches long and 15 inches wide. I attached a picture of a heavier tractor being loaded with these ramps as well as a review video for more info as well.
  view full answer...
  
• Trailer Ramps With 10,000 Capacity to Load Truck
  We do have an option for trailer ramps that have the weight capacity you need in order to load your 2015 Ford F-450, which from my research looks to have a curb weight of just under 9,000 lbs. So the ramps that will work for you are the Gen-Y Hitch Aluminum Loading Ramp Set # 325-GH-R96. This ramp set has a combined 10,000 lb capacity (5,000 lbs per ramp) which means it will be able to handle the weight of your F-450 (though I do recommend verifying the curb weight of your truck). These...
  view full answer...
• What Car Loading Ramps Can I Use for Van Trailers 48 Inches High?
  For a ramp used to load vehicles, it is important to have a high maximum weight capacity. With that being said, I recommend the Gen-Y Hitch Aluminum Loading Ramp Set - 144" Long x 15" Wide - 8,000 lbs # 325-GH-R96. The Gen-Y Hitch Aluminum Ramp has a per-ramp weight capacity of 5,000 pounds (10,000 pounds total). As far as the 48-inch rise requirement, the Gen-Y is a great choice. I went ahead and attached a video that shows the ramp being used on the side of a trailer that is about 36...
  view full answer...
• Can Gen-Y Aluminum Loading Ramps # 325-GH-R96 Be Used to Span Dip for Backing Up Camper
  As long as they provide the needed length and track width, the Gen-Y Hitch Aluminum Loading Ramp Set # 325-GH-R96 that you referenced will work great for your application. They provide plenty of strength (10,000 pound capacity for the pair - which represents the highest rated set we have available) and their angled base will allow you to maintain an ideal loading angle for the camper and your Silverado. A flat set like this will work well to avoid dragging the skid plates on the trailer...
  view full answer...
• Best Lightweight Loading Ramp for Vehicle with Low Ground Clearance
  The best loading ramps we offer for vehicles with low ground clearance are the Gen-Y Hitch Aluminum Loading Ramp Set like part # 325-GH-R96 which are 8' long. Therefore they should allow for a very shallow approach angle. These ramp are also lightweight at around 50 lbs each so you can move them by yourself.
  view full answer...
• Trailer Deck Height Range for 96" Long Gen-Y Hitch Aluminum Loading Ramp Set
  The range of height for the Gen-Y Hitch Aluminum Loading Ramp Set - 96" Long x 15" Wide - 10,000 lbs # 325-GH-R96 is 20" - 36". This would be from the ground to the deck. I confirmed this with my contact at Gen-Y.
  view full answer...
• Gen-Y Hitch Loading Ramps # 325-GH-R96 for a 5,000 lb Scissor Lift
  Each ramp included with the Gen-Y Hitch Aluminum Loading Ramp Set # 325-GH-R96 can support up to 5,000 lbs each for a total of 10,000 lbs when the equipment being loaded is supported by both ramps. This weight capacity will be more than enough to use with your 5,000 lb scissor lift as long as you are able to use both ramps to support the weight of the scissor lift. Of course, your trailer will also need to be rated high enough to handle the 5,000 lb scissor lift. Check out the video linked...
  view full answer...
• Aluminum Thickness of Gen-Y Ramp Set 325-GH-R96
  I checked with Gen-Y and they informed me that their ramp set part # 325-GH-R96 is made from a double hollow tube, 3” x 5”, with a wall thickness of .125 A6063 alloy. This includes the hook end of the ramps as well.
  view full answer...
• Hooked End Of Gen-Y Hitch Aluminum Loading Ramp Set # 325-GH-R96 Opening Measurement
  The Gen-Y Hitch Aluminum Loading Ramp Set # 325-GH-R96 has a gap of 1-1/2" for the distance between the ramp and the 1/4" hooked end which fits onto the trailer(see image).
  view full answer...
  
• Can Tracked Equipment Be Loaded on Trailer Using 10K Gen-Y Hitch Aluminum Loading Ramp Set
  As long as the tracks are rotating/moving when you're loading your excavator you'll be just fine using the Gen-Y Hitch Aluminum Loading Ramp Set # 325-GH-R96. That note is essentially saying not to drag something heavy up the ramp. A better terminology would probably be "rolling equipment" instead.
  view full answer...
• Solution for Tilt Trailer that Doesn't Have Lip to Use Gen-Y Aluminum Loading Ramp 325-GH-R96
  Since you don't have a lip on your tilt trailer for the Gen-Y Aluminum Loading Ramp Set part # 325-GH-R96 to attach to you'd need to find a welder/fabricator near you who can add that to your trailer as we don't have anything that would provide that.
  view full answer...
• Can 10k Gen-Y Hitch Aluminum Loading Ramp Set be Used with 6k Track Loader
  Since your track loader is only 6,000 lbs and the weight capacity of the Gen-Y aluminum loading ramps part # 325-GH-R96 is 10,000 lbs they'd easily work well for you. The tracks wouldn't put any additional stress on the ramps compared to tires and there isn't any type of time restriction that the machine would need to be off of them either.
  view full answer...
• Is the Weight Rating for a Set of Loading Ramps Per Axle
  The Gen-Y Hitch Aluminum Loading Ramp Set part # 325-GH-R84 has a 6,000 lb weight capacity which is for one axle. In most cases, both axles will never be on the ramp together so as long as the weight on either axles does not exceed 6,000 lbs then you will be good to go. However, if at any time there is more than 6,000 lbs on one axle you would need to upgrade to the Gen-Y Hitch Aluminum Loading Ramp Set part # 325-GH-R96 which has a 10,000 lb per axle weight capacity. I have attached...
  view full answer...
• Are There Trailer Ramps for Loading Cars That Keep Front End Up for Door Clearance
  We have options for loading ramps for a trailer to load up your vehicle, but none that are 10 inches or keep the front end up for door clearance when towing. Each of the available ramps hook onto the trailer and need to be removed after use; they are different lengths, widths, and capacities so you can get the one that will work for your vehicle. - 72" Long x 14" Wide - 6,000 lbs: Gen-Y Hitch Aluminum Loading Ramp Set # 325-GH-R72 - 84" Long x 14" Wide - 6,000 lbs: Gen-Y Hitch Aluminum...
  view full answer...
• Ramp Set that Could be Used with 1997 Ford F-800
  A 1997 Ford F-800 can be pretty heavy based on how it is equipped. The best ramp set we have for that application would be the Gen-Y Ramps part # 325-GH-R96 have a 10,000 lb capacity. You'd still want to verify the weight of the truck though as it's possible it could weigh more than that. These ramps are 96 inches long and 15 inches wide.
  view full answer...
• Recommended 8 Foot Long Flat Ramps For Car Hauler Trailer
  I may have a solution for you, but we don't have the CargoSmart Arched Loading Ramp Set - Non-Folding - Aluminum - 90" x 12" - 3,000 lbs # 3483070 in a non-arched ramp. The only available flat ramp we have in close to 90" is the Gen-Y Hitch Aluminum Loading Ramp Set - 96" Long x 15" Wide - 10,000 lbs # 325-GH-R96. These are a heavy duty ramp set that is well rated for your race car and comes in an 8 foot long x 15" wide ramp section. I've linked a review video of these ramps for you to...
  view full answer...
• Why is there a Height Limit on Aluminum Car Hauler Ramp Set 288-07502
  The height restriction on ramp set # 288-07502 has to do with the distribution of the weight, ability for tires to grip, and clearance between the tops of the ramps and the vehicle rolling up them. The shorter the ramp the more severe the angle will be as the loading height increases. You could go with longer (and tougher) ramps using the Gen-Y options such as # 325-GH-R72, # 325-GH-R84, or # 325-GH-R96. These ramps will last pretty much forever since Gen-Y is known for making products...
  view full answer...
• What Type Of Ramp Do I Need To Load My 2002 F-250 Super Duty On A Trailer
  I did some research and your truck may weigh anywhere from just under 5,600 lbs to 6,182 lbs. You will be cutting it close with the Aluminum Car Hauler Ramp Set - 72" x 14-1/2" - 6,000 lbs - Qty 2, part # 288-07503. If your 2002 F-250 Super Duty comes in less than 6,000 lbs, you should have no problems with this ramp. If it weighs more than 6,000 lbs I cannot recommend it, no matter how little you plan on using it for this truck. The Gen-Y Hitch Aluminum Loading Ramp Set - 96" Long x...
  view full answer...
• What Ramps Are Good For Loading A Car Onto A Flat Bed Truck
  I do not think the Aluminum Car Hauler Ramp Set - 72" x 14-1/2" - 6,000 lbs - Qty 2 # 288-07503 would be the safest set of ramps for this particular job. They can handle the weight of the car no problem but looking at the picture you provided I do no think the angle of the ramps will be low enough to let the car get on the flat bed without bottoming out. I definetly recommend going with a longer set of ramps like the Gen-Y Hitch Aluminum Loading Ramp Set - 96" Long x 15" Wide - 10,000...
  view full answer...
  
• Gen-Y Ramp Recommendation for 10K Crown C-5 Forklift
  The Gen-Y Hitch Aluminum Loading Ramp Set - 96" Long x 15" Wide # 325-GH-R96 have a combined weight capacity of 10,000 lbs. As long as your Crown C-5 forklift does not exceed this weight capacity they will be able to handle the 10K weight. In all honesty though I'm not a fan of max-in out the weight capacity of anything so since you're right at the max rating of this ramp set I recommend going with the Gen-Y Hitch Aluminum Loading Ramp Set - 120" Long x 15" Wide # GY52YR instead because...
  view full answer...
• Will the Gen-Y Hitch Aluminum Loading Ramp Set Work with a Skid Steer
  The Gen-Y Hitch Aluminum Loading Ramp Set part # 325-GH-R96 have a capacity of up to 10,000 lbs for the pair. If you need a higher capacity, they also offer the Gen-Y Hitch Aluminum Loading Ramp Set part # GY52YR which have a capacity of up to 14,000 lbs for the pair. In regards to using the ramps with a skid steer, there are no exclusions about this from the manufacturer nor do they specify anything about not using vehicles with rubber tracks. Therefore, so long as you are under the...
  view full answer...
• Recommended Widest Available Car Ramps
  I may have a solution for you, but the Gen-Y # GY96FR ramps only come as wide as 15". There is not a ramp with a similar 6,000-lbs total (combined) but you could get a wider ramp with the Loading Ramp Set - Aluminum - 65" Long x 20-1/2" Wide - 3,000 lbs - Qty 2 # 288-07489, which is 20-1/2" wide. The only downside to going this route is that these ramps only have a 3k capacity (combined). There is a 15" wide Gen-Y ramp set with the Gen-Y Hitch Aluminum Loading Ramp Set - 96" Long x 15"...
  view full answer...

Do you have a question about this Car Ramp?