Adding Transmission Fluid After Installing Transmission Cooler on 2013 Toyota Tacoma 2.7L

Question

Question:

Hello, I am looking at installing a transmission cooler on my 2013 Toyota Tacoma 2.7 4 cylinder truck. Will I need to add more transmission fluid after install even if no fluid leaks out?

asked by: Nick P

0

Expert Reply:

Because adding an auxiliary transmission cooler and additional hose length extends the overall cooling system, it is likely that you will need to add a bit more transmission fluid even if no fluid is lost during installation. Often adding a cooler requires adding somewhere between 1/2 pink up to 1 quart of additional fluid.

It is a good idea to add fluid a little at a time, testing the dip stick as you go along, until the system no longer indicates it is low on fluid.

If you have room for it, the Derale Transmission Cooler # D13503 is a great, large size cooler for your Tacoma. This cooler measures 11 inches W x 8-3/4 inches T x 7/8 inches D.

I have attached a link to all of the transmission coolers for your Tacoma with 2.7L I4 engine.

expert reply by: Victoria B

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Hi Russ; you pretty much have everything you need right there with the exception of a few parts. I'm going to go ahead and list it all out here with links to make it easy for your to manage. You will need the following: -etrailer Invisible Base…

view full answer...

Answer 3

Hello Paul, Definitely a good idea to keep your transmission cooled while pulling a 38' 5th wheel. I found another option that I thought would fit your needs a little better, I went ahead and reached out to my contact at Derale and he agreed. The…

view full answer...

Answer 4

It is possible that the weight distribution system you are using is rated too high for the total tongue weight of the trailer. Total tongue weight is the tongue weight of the trailer when loaded and ready to tow plus the weight of anything loaded…

view full answer...

Answer 5

I do have a solution for you, but when I spoke with my contact at Air Lift she said that the frame on your 2017 GMC Canyon with the diesel engine is slightly different. Because of this the Ride Control #AL59533 you referenced doesn't line up…

view full answer...

Answer 6

You can install a stack cooler in your vehicle. The Class ratings are there as a reference point to a hitch Class. For example if someone has a Class III hitch they can look at coolers, see a Class III and say, hey, I have a Class III hitch so this…

view full answer...

Answer 7

The need for an accumulator tank like the Seaflo Accumulator Tank #SE38FR with the Excel RV Tankless On-Demand Water Heater #EX93FR would depend solely on the pressure of your water pump. This water heater requires a water pressure of 2 psi up to 120…

view full answer...

Answer 8

Derale Fluid Control Thermostat Kit w/ 3/8" NPT Ports #D13011 and the Transmission cooler #D13503 will work well on your 2013 Sienna. The thermostat is your fail safe, so I recommend putting it between your transmission and the secondary cooler.…

view full answer...

Answer 9

Equal-i-zer is a brand that makes weight distriubution systems. But just like with Kleenex and tissue, people use the term equalizer to mean any weight distribution hitch. The actual Equal-i-zer systems do have built in sway control so I would assume…

view full answer...

Adding Transmission Fluid After Installing Transmission Cooler on 2013 Toyota Tacoma 2.7L

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching