Trailer Jack Replacement Solution for Shelby 5774

Question

Question:

Hi, I have a Shelby Jack 5774 not sure if it’s a 5, this jack actually bolts to a frame bracket welded to the frame with 4 bolts, no U bolts or plates, the trailer brand is Extreme. Anyway it won’t go up or down, crank turns. I’d like to replace it with the same

asked by: Jon M

0

Expert Reply:

We aren't going to have a jack that's going to bolt right up to the same mounting bracket your Shelby mounted to so your best option will be to cut off the old mounting bracket and weld on a new one like with what you could do with the Fulton part # FTJ120W0301. This jack will work great and once the bracket is welded to the trailer will also be very easy to use. Check out the review video link I attached for the jack for more info as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Based on my research, the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will be a perfect replacement for your Shelby 5756A trailer jack. This jack will allow you to use the existing snap ring jack mount on your trailer for installation.…

view full answer...

Answer 2

The Shelby #5776 is the direct replacement for the #5756, but we do not offer that particular jack. The Fulton #FTJ120W0301 that you referenced would make an acceptable replacement. The capacity and the amount of lift or travel is identical. Both…

view full answer...

Answer 3

What we have heard is that the Fulton #FTJ120W0301 does fit the mounting plate of the Shelby Jack 5784.

view full answer...

Answer 4

What we have heard is that the Fulton #FTJ120W0301 does fit the mounting plate of the Shelby Jack 5784. This will be your best option. This jack has a 1,200 lb lifting capacity which would be more than enough.

view full answer...

Answer 5

What we have heard is that the Fulton #FTJ120W0301 does fit the mounting plate of the Shelby Jacks like what you have. This would be our best option.

view full answer...

Answer 6

I tried searching for the part number you listed but could not find anything with Fulton or online. However, if the mounting bracket on your trailer looks like the part #P9012-00 the Fulton Jack part #FXP10W0301 is going to fit and work well.

view full answer...

Answer 7

As long as your current bracket measures 2-1/8" from the center of the bolt to one of the pin holes then the Fulton Bolt-Thru Swivel Marine Jack #FXP10W0301 will work great as a replacement for your Shelby 5784 bolt-thru jack.

view full answer...

Answer 8

I contacted our representative at Fulton about the Fulton Round, Snap-Ring Swivel Marine Jack, part #FTJ120W0301. The inner diameter of the mounting hole is 2-1/2 inches. He informed me that up to a few years ago the Fulton jacks were made in…

view full answer...

Answer 9

To replace your Shelby 5856A jack I recommend the Fulton Round Snap-Ring Swivel Marine Jack #FTJ120W0301. We have had customers say that this fits the mounting plate for the Shelby 5784A perfectly so ti's going to be the easiest install possible.…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to our research the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will fit as a replacement for your Shelby 5756 boat trailer jack. It will allow you to keep the same bracket that is currently welded-on. You basically need to open…

view full answer...

Trailer Jack Replacement Solution for Shelby 5774

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching