How Tight Should Nut and Cotter Pin of Trailer Hub/Drum Be
Question:
hello, i just replaced the hub assembly on my boat trailer and i see mixed answers to the question of how tight should the castle nut be..most say after seating the new bearings, back off the castle nut, then hand tighten and put in cotter pin. if the hole isnt lined up when its hand tightened, then back off until hole is aligned and you can put pin in.. i did that, but there seemed to be quite a bit of play, so i was torn on what to do.. when i tighten it up to the next space, it seems too tight, but it gets rid of the play.. but i read where if its too tight, it could overheat. its like a dam if i do, dam if i dont deal. could i add a washer, or get another that is a little thinner than the original so the holes line up with a little more pressure from the castle nut? i decided to change out this hub because i noticed a little play that i didnt think was there before. if i do go with the finger tightened alignment, there will actually be more play then i had with the old hub assembly.. sorry i rambled on, but we are leaving on vacation in less than a week, and pulling the boat about 1000 miles! thanks..
asked by: Dave
Expert Reply:
I like your idea of finding a thin washer so that you get a snug, but not too tight, fit that allows you to fit the cotter pin through. Typically a washer isn't needed but it sounds like your hub is the perfect storm of being right between two holes.
When it's on the tighter side does the wheel still spin as freely as the looser side? If so, then that would be okay to use.
Product Page this Question was Asked From
Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- Bearing Kits
- Bearing L44649 and L68149
- Race L68111 and L44610
- 3500 lbs Axle
- etrailer
more information >
Continue Researching
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Video: Setting Up Your MORryde Suspension Upgrade Kit - 2022 Grand Design Imagine XLS Travel Trailer
- Video: In-Depth Review of the Easy Grease Trailer Idler Hub Assembly for 3.5K Axles
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Pre-Greased
- Search Results: karavan fenders
- Article: How to Accurately Measure Trailer Leaf Springs
- Search Results: spindle nut retainer
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Shop: Trailer Square U-Bolts (Qty 2), 2-1/8" x 4" x 7/16"
- Shop: Dexter Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2
- Q&A: Do Hub Races Have to Be Replaced Each Time Bearings Are Changed
- Q&A: Can Bearing Buddy Fit on EZ Lube Spindle that has Zerk Fitting
- Q&A: Replacement Bearing Recommendation for H-1377 Idler Hub
- Q&A: Should Center Plug of Grease Cap Plug E-Z Lube Grease Caps # RG04-010 be Pushed Out All the Time
- Q&A: Correct Replacement for UFP H-1377 Trailer Hub
- Video: Ultimate Overview of the MORryde Suspension Upgrade Kit for Tandem Axle Trailers
- Q&A: Replacement Hub for a UFP H-1377 on a 2004 Tahoe Boat Trailer
- Q&A: Replacement Hub, Bearings, Races, and Seals for Trailer Hub with H-1377 Bearing
- Shop: MORryde Suspension Upgrade Kit for Tandem Axle Trailers - 2-1/4" Long Shackle Straps
- Shop: Replacement U-Bolt for 2" Wide, Square Axles - 7/16" Diameter - Zinc Plated
- Search Results: 9/16 lug nut
- Video: Remove, Inspect, and Reinstall Trailer Bearings, Race, and Seals Demonstration
- Search Results: lippert 4400 lb axle
- Search Results: axle caps
- Search Results: trailer leaf springs
- Video: Measuring To Choose The Right Trailer Axle
- Shop: Trailer Hitch
- Search Results: trailer suspension parts
- Article: Most Popular Wheel Bearings
on Trailer Bearings Races Seals Caps
