Wheel Covers Hubcaps Specs:
Features:
Replaces 1 mirror-polished stainless steel wheel cover on the rear of your Ford truck. Fits a 19-1/2", 8-lug wheel with 10 hand holes. Hardware included.
Installation Notes:
Designed for models with dual rear wheels only
More Information >Wheel Covers Hubcaps Specs:
Features:
Replaces 1 mirror-polished stainless steel wheel cover on the front of your Ford truck. Fits a 19-1/2", 8-lug wheel with 10 hand holes. Hardware included.
Installation Notes:
Designed for models with dual rear wheels only
More Information >Wheel Covers Hubcaps Specs:
Features:
These stylish wheel covers fit your vehicle that has 19-1/2", 8-lug wheels with 8 hand holes. The plastic covers are finished with mirror-polished stainless steel, and they easily snap into place - no hardware required.
Installation Notes:
Designed for models with dual rear wheels only
More Information >Wheel Covers Hubcaps Specs:
Features:
Stylish, durable stainless steel wheel covers with a mirror polish will dress up your Ford that has 19-1/2", 8-lug wheels with 8 hand holes. Includes 4 hubcaps, hardware and a dual-tire inflation kit.
Installation Notes:
Designed for models with dual rear wheels only
More Information >Videos
for Wheel Well Liner
Help Articles
for Wheel Well Liner
Expert Answers
for Wheel Well Liner
The Gen-Y Weld-On 2" Receiver Tube #325-GH-003 is 2-7/8" wide on the tube and 3-1/2" wide at the collar. The overall length is 12".
view full answer...In almost all cases 3,500 lb axles will all use the same bearings. If your trailer has a Lippert or Dexter 3,500 lb axle then yeah they would be the same. But to be safe it won't hurt to pull them off and get the numbers. If you are sure you…
view full answer...For your 2014 Ford F-250/350 Super Duty you will want to use Wheel Masters 4-Hose Inflation Kit part #WM8001. The bend on the Wheel Masters 4-Hose Inflation Kit part #WM8001-135 causes the hoses to be in contact with your rim as soon as it comes…
view full answer...Although we do not have a direct replacement for the Dicor V19582-EJN, the Replacement Wheel Master Lug Nut Cover for Wheel Liner - Qty 1 #WMRMT9061 will fit a 22 millimeter lug nut. From what I have found, the jam nut you are looking for has been…
view full answer...I can absolutely tell you the difference between the two options. The Kwikee 38 Series Electric Step #LC3723383 comes with a control module, which means it will automatically extend. The Kwikee 38 Series Electric Step #LC372338 does not come with…
view full answer...For replacing the Drive Head #LC34FR and Idler Head #LC87FR on a Solera Slide Topper you will want to completely remove the slide topper from your RV/Camper. You will need to insert a pin into the end of the tube end cap(see image) to keep the…
view full answer...I do have options for you, but the Wheel Masters Inflation Kits are not vehicle specific parts. They are going to depend on the wheel set-up that you have. However, I can provide you with a couple of the most common options we typically see on the…
view full answer...The 6-Leaf Double-Eye Spring for 4,500-lb Trailer Axles - 26" Long #e27SR will be the closest fit for your 3750 lb axle. Having leaf springs rated slightly higher is normal because you will be limited in capacity by the weakest component on your…
view full answer...No, the E-Coat is not to be removed from the rotors. The E-coat is a protective coat that will prevent corrosion but it will not cause issues with coating your brake pads or have any negative impact. The Dexter Disc Brake Kit - 10" Hub/Rotor - 5…
view full answer...The hub covers that I have are only available in chrome ABS finish. The Quick Trim Chrome Finish Trailer Hub Cover 6 on 5-1/2, part #QT655C, is a cover that will fit a 6 on 5-1/2 inch bolt pattern wheel. The Quick Trim Chrome Finish Trailer Hub Cover…
view full answer...The best supplemental braking system for your 1984 Jeep CJ-7 is going to be the SMI Stay-IN-Play DUO Supplemental Braking System part #SM99251. The Stay-IN-Play DUO is a proportional system which means it will activate the brakes in your toad at the…
view full answer...As far as a left-threaded or right-threaded cap for your motorhome, right-handed threads run clockwise, and left-handed threads run counterclockwise. The reason for this difference is that some applications of screws can come loose with the motion of…
view full answer...Filter Products (8)
Contact and Help
What our customers are saying:
The people answering the phones were professional & knowledgeable. All this and the best prices on the internet, How can you go wrong?
Bill
Vero Beach, FL