Subaru Outback WagonBrake Controller with Wiring

change vehicle

Select Subaru Outback Wagon Year

Available Years for Subaru Outback WagonBrake Controller with Wiring

Trailer Brake Controllers

Proportional Brake Controller

Time Delay Brake Controller

Air to Electric Brake Control

Universal Brake Controller Wiring Kit

Wireless RF Brake Controller

Trailer and Brake Parts

Trailer Breakaway Kits

Trailer Brakes

Trailer Hubs and Drums

Trailer Tires and Wheels

Brake Actuator Couplers

Wire, Adapters and Trailer Harness

Brake Controller Manufacturers

Tekonsha Brake Controller

Hopkins Brake Controller

Draw-Tite Brake Controller

Hayes Brake Controller

Dexter Brake Controller

Subaru Outback Wagon Brake Controller Videos

Trailer Brake Controller Installation - 2006 Subaru Outback Wagon

Today on this 2006 Subaru Outback Wagon were going to install part number 90195 from Tekonsha. Also to install this brake controller were going to use the install kit, part number ETBC7. Were going to start off our assembly by getting the ETBC7 kit ready. Well start off by hooking up our gray cable to our seven and four pole adapter. Well wrap up our seven pole adapter wires with electric tape leaving out the four pole. The blue wire which is our brake wire and a black wire which is a 12 volt power supply.

Subaru Outback Wagon Brake Controller Questions and Answers

• Recommend Brake Controller For 2003 Subaru Outback
  
• Brake controllers are not vehicle specific. If you plan to tow a trailer with electric brakes, you would need to install the T-One Vehicle Wiring Harness, part # 118461 and the Brake Controller 7 and 4 Way Installation Kit, part # ETBC7. For a brake controller, I would recommend the Tekonsha Prodigy P2 Brake Controller, part # 90885, as it is easy to setup and operate. The P2 is a proportional brake controller. A proportional brake controller sends power to the brakes in proportion to the rat
  view full answer...


• How to Wire a 2011 Subaru Outback for a Brake Controller
  
• The 2011 Subaru Outback is not equipped with an under-dash connector for installing a brake controller, but a controller can still be installed using our Brake Controller Install Kit, part # ETBC7 if a 7-way trailer connector is needed, or # ETBC6 for a 6-way connector. The install process, although a bit involved, is pretty straightforward and can be completed by the average do-it-yourselfer. We have plenty of help available online through the website, through our experts, or by phone. Ot
  view full answer...


• Brake Controller Recommendation for a 2010 Subaru Outback Wagon
  
• The Draw-Tite Brake Controller, # 5100, will work in reverse. It will engage the trailer brakes any time the vehicle brakes are used. The Prodigy P2, # 90885 will also work in reverse. The main difference between these two controllers is that the Draw-Tite is a time delay controller and the Prodigy is a proportional controller. Time delay controllers have the benefit of being able to mount in any position. However, these types of controllers apply the same amount of braking to the trailer bra
  view full answer...


• Brake Controller for a 2008 Subaru Outback with Factory Wiring
  
• Sure, the Draw-Tite 2-4 Brake Electronic Brake Controller, part # 5100, will work with your 2008 Subaru Outback. You will need to install the necessary additional wiring to operate the brake controller. Most people will purchase the Brake Controller Installation Kit, part # ETBC7, which includes a 4-pole to 7-way and 4-way adapter and all the necessary wire to complete the installation. You will have to hard wire the wires coming out of the back of the 5100 to your Subaru and the wires you will
  view full answer...