Hitches are custom designed by Draw-Tite, Reese, Hidden Hitch, Curt, and Bosal to fit your Pontiac. Choose the hitch that is right for your towing needs and your budget.
All hitches come with a limited lifetime warranty and are manufactured in the USA.
We offer over a custom hitch for virtually every Pontiac on the road.
What our customers are saying:
Ordered the hitch and light connector for an 06 Santa Fe. Received the components in a timely fashion. Installation of both the hitch and the light connector took only a couple of hours. The hardest part was disconnecting the muffler rubber mounts to install the hitch, and pulling out the clips on the carpeting to get inside to make the electrical connections. Thanks.
Custom fit trailer hitches are available for virtually every vehicle. At etrailer.com we carry rear mount trailer hitches, front mount, fifth wheels, goosenecks, RV trailer hitches, and weight distribution systems from the best manufacturers such as Draw-tite, Hidden Hitch, Reese, Valley, and Curt. You will also find a complete selection of hitch accessories and related products such as bike racks, cargo carriers, hitch covers, ballmounts, and locks.
More Trailer Hitches
Trailer Hitch Manufacturers
Trailer Hitch Installation - 2008 Pontiac Vibe - Hidden Hitch
Today on this 2008 Pontiac Vibe we are going to install part number 60958 from Hidden Hitch. This is what the hitch looks like when it is installed on the vehicle. Next well give you some measurements that will help you out in selecting accessories such as a bike rack or a cargo carrier. From the top of the receiver opening down to the ground will be 12 inches and from the center of the hitch pinhole to the edge of the bumper will be 4 inches. Now we are going to show how the hitch is installed. Well go ahead and show you where the hitch mounts up on to the frame and uses this threaded holes.
Trailer Hitch Installation - 2008 Pontiac Vibe - Draw-Tite
Today on this 2008 Pontiac Vibe we're going to install part number 24812 from Draw-Tite. This is what the hitch looks like when it is installed on the vehicle. Next well give you measurements to help you out in selecting some accessories such as the bike rack or a cargo carrier. From the top of the receiver opening down to the ground is going to be 11 5/8 inches and from the center of the hitch pinhole to the outside edge of the bumper is going to be 2 inches. Now well go ahead and show you how the hitch is are installed. When you install the hitch its going to use these locations of the frame here.
Trailer Hitch Installation - 2009 Pontiac Vibe
Today, were working on a 2009 Pontiac Vibe. We are going to install a draw-tite hitch part number 24812. This will be comparable with hidden hitch part number 60898. Here are a couple of measurements that will assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost point of the bumper is 3 inches, and from the top of the receiver to the ground is 11 inches. This will assist you with selecting accessories such a draw bar, a bike rack or a cargo carrier.
Trailer Hitch Installation - 2006 Pontiac Vibe
Today we are working on a 2006 Pontiac Vibe. We will be installing a Draw-Tite hitch part number 24812. This will also be comparable to Hidden Hitch part number 60898. Now here are a couple of measurements that will assist you with ing accessories for your new hitch, such as a draw bar, a bike rack or a cargo carrier. From the center of the hitch pin hole to the outer most point of the bumper is approximately 2 inches. And from the top of the receiver tube to the ground is 11 inches. Now let us go ahead with the installation. 0:31
Trailer Hitch Installation - 2010 Pontiac Vibe
Today on this 2010 Pontiac Vibe we are going to install part number 24812 from Draw-Tite. This will also apply to Hidden Hitch part number 60898. This is what the hitch looks like when installed on the vehicle. We are going to give you a couple measurements that will help you out when ing accessories such as a ball mount, bike rack, or cargo carrier. From the top of the receiver tube to the ground is 10-7/8inches. From the center of the pin hole out to the edge of the bumper is 3 inches. No we are going to show you how the hitch gets installed on this vehicle. :33
Today, on this 2009 Pontiac Vibe, we will be installing Curt hitch part number 12228. Okay, we are underneath the vehicle and we are looking at the drivers side frame rail. As you can see here at the end of the frame , we have got two existing weld nuts. Those are going to provide our two attaching points on the drivers side for our trailer hitch. We will be attaching the hitch to the weld nuts using the 12mm bolts and conical tooth washer. And on the passenger side, we will be using the same two weld nuts and same bolt washer combination. Over here on the passenger side, you will need to lift the hitch up over the exhaust. 0:31
Trailer Hitch Installation - 2004-05 Pontiac Vibe
This is a hitch on a 2004-05 Pontiac Vibe. This one has preexisting fasteners in the frame right here, which in this case are a little bit corroded out. So, we will have to clean them out first with a bolt and some WD-40 to run through so we can fasten the hitch on. We already sprayed down the bolt. Then we are just going to run the bolt a little bit and then back them up. Put a little bit more in and go at it again. Just keep going at it until the bolt starts to spin freely, like it is doing now. You probably will not have to worry about much like that. One down, three to go. Work on the other two. Sometimes they do not go in right off the bat. And once you get the bolt half way in, it backs out pretty easy. Chances are you are pretty much down with that part.
Subscribe to email newsletter
privacy - we don't send unsolicited email
All images, layout and content copyright etrailer.com