view cartView Cart

CALL NOW - 800-298-8924

Product Experts Available Now!

Free Shipping on Orders Over $50

Only 12 Hours 30 Minutes Remaining


Buy a Hidden Hitch or Draw-Tite branded hitch with a 2 inch receiver and get a free anti-rattle hitch pin

Ford F-250 and F-350 Super Duty Trailer Hitch

change vehicle

Select Ford F-250 and F-350 Super Duty Year

Trailer Hitch

Custom fit Trailer Hitch for your:



Available Years for Trailer Hitch



Trailer Hitches for Ford F-250 and F-350 Super Duty

Hitches are custom designed by Draw-Tite, Reese, Hidden Hitch, Curt, and Torklift to fit your Ford F-250 and F-350 Super Duty. Choose the hitch that is right for your towing needs and your budget.

All hitches come with a limited lifetime warranty and are manufactured in the USA.

We offer over a custom hitch for virtually every Ford F-250 and F-350 Super Duty on the road.




What our customers are saying:

Ordered hitch on a Tuesday afternoon, hitch arrived Thursday morning !! Very impressive shipping time !!! Loking forward to installing hitch on the vehicle !!!

Michael

Pittsburgh, PA






Trailer Hitches, Front Mount Hitches, Fifth Wheels, Goosenecks, RV Hitches, and Weight Distribution

Custom fit trailer hitches are available for virtually every vehicle. At etrailer.com we carry rear mount trailer hitches, front mount, fifth wheels, goosenecks, RV trailer hitches, and weight distribution systems from the best manufacturers such as Draw-tite, Hidden Hitch, Reese, Torklift and Curt. You will also find a complete selection of hitch accessories and related products such as bike racks, cargo carriers, hitch covers, ballmounts, and locks.


Hitch Accessories



More Trailer Hitches



Trailer Hitch Manufacturers






Ford F-250 and F-350 Super Duty Trailer Hitch Videos

Trailer Hitch Installation - 2004 Ford F-250 - Curt

Today on our 2004 Ford Super Duty, well be installing the Curt Class V - 2 Receiver Tube Hitch, part number C15410. To begin our install, well first point out the attachment points. Well have a total of 8 attachment points, 4 on each side. These holes are pre-drilled into the frame by the manufacturer. Well be using the new hardware provided with the hitch. There will be a carriage bolt and block, theyll go down through the frame, through the hitch, and get secured with a flange nut. To start, well put our rear and forward attachment point hardware in place, on both sides. Then with an extra set of hands, well go ahead and raise the hitch up into position and install the flange nut. Now that we have the hardware holding the hitch in place, well go ahead and put the other 4 fasteners in place.



Trailer Hitch Installation - 2003 Ford F-350 - Curt

Today on our 2003 Ford F350, well be installing the Curt hitch, part number c15410. Next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is three inches, to the top of the inside of the receiver tube opening to the ground is 16-3/4. This will assist you with selecting accessories such as a ball mount, a bike rack, or a cargo carrier. Now lets go ahead with installation. Note for this application is recommended to lower and remove the spare tire for the ease installation of installing the hitch, however; unfortunately we cannot lower the spare tire as we installed this hitch.First well go ahead and identify our attachment points, there are a total of eight attachment points, four on each frame rail, these are predrilled holes in the frame rail by the manufacture.



Trailer Hitch Installation - 2004 Ford F-250 - Hidden Hitch

Today on our 2004 Ford F250 well be installing Hidden Hitch, part number 87618. This is what our hitch will look like once its installed. Next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch such as a draw bar, a bike rack, or a cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is five and a half inches. From the top of the receiver tube to the ground is 17 and a half inches. Now lets go ahead with installation.



Trailer Hitch Installation - 2004 Ford F-250 - Draw-Tite

Today on our 2004 Ford F250 well be installing the Draw-Tite hitch, part number 75740. This is what our hitch will look like once its installed. Next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch such as a draw bar, a bike rack, or a cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is five and a half inches. From the top of the receiver tube to the ground is 17 and a half inches. Now lets go ahead with installation.



Trailer Hitch Installation - 2004 Ford F-250 - Reese

Today on our 2004 Ford F250 well be installing the Reese Titan trailer hitch, part number 45297. This is what our hitch will look like once its in position. Next well go ahead and give you a couple of measurements to assist you when selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is two inches. From the top of the receiver tube to the ground is 17 and a half inches. Now lets go ahead with installation.



Trailer Hitch Installation - 2004 Ford F-250 - Draw-Tite

Today on our 2004 Ford F250 well be installing the Draw-Tite Max-E-Loader trailer hitch, part number 41552. This is what our hitch will look like once its installed. Next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch such as the draw bar, a bike rack, or a cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is three inches. From the top of the receiver tube to the ground is 18 inches. Now lets go ahead with the installation.



Trailer Hitch Installation - 2004 Ford F-250 - Curt

Today on our 2004 Ford F250 well be installing the Curt hitch, part number 15601. This is what our hitch will look like once its installed. Next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is three and a quarter inches. From the top of the receiver tube to the ground is 17 and three-quarter inches. Now lets go ahead with installation.



Trailer Hitch Installation - 2004 Ford F-250 - Curt

Today on our 2004 Ford F250 well be installing the Curt hitch, part number 14041. First well note that weve already gone ahead and lowered and removed the spare tire for an easier install. Note weve got a total of six attachment points, three on each side. These attachment points are predrilled holes in the frame by the manufacturer. The hardware well be using to attach the hitch is the new half inch carriage bolt and block and a half inch flange nut. Well first go ahead and take the carriage bolt and block and drop into the frame, which will then go through the hitch and be secured with the flange nut at each of the attachment points.



Trailer Hitch Installation - 2004 Ford F-250 - Curt

Today on our 2004 Ford F250 well be installing the Curt hitch, part number 13355. This is what our hitch will look like once its installed. Next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch such as a draw bar, a bike rack, or a cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is five inches. From the top of the receiver tube to the ground is 17 and three-quarter inches. Now lets go ahead with installation.



Trailer Hitch Installation - 2004 Ford F-250 - Curt

Today on our 2004 Ford F-250, well be installing the Curt Hitch, part number C14355. This is what our hitch will look like once its installed. Next, well go ahead and take a couple of measurements to assist you in selecting accessories for your new hitch such as a draw bar, a bike rack, or a cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is 5 inches. From the top of the receiver tube to the ground is 17-3/4 inches. Now, lets go ahead with the installation.



Trailer Hitch Installation - 2008 Ford F-250 - Curt

Today on this 2008 Ford F-250, we're going to install part number C14355 from Curt. All right, this is what the hitch looks like once installed on the truck. Next, we'll go ahead and give you some measurements to help you out in selecting some accessories. From the top of the receiver opening down to the ground will be 15 inches. One thing to know about the bumper on this is the aftermarket. Basically, the hitch pin hole is ahead of the bumper by about 1-3/4 inches.



Trailer Hitch Installation - 2000 Ford F-250 and F-350 Super Duty

Today on this 2000 Ford F-350 Super Duty we are going to install part number V82500 from Valley. I will go ahead and show you where the hitch mounts up on the frame of the vehicle. It is going to use these existing holes in the frame itself so you will not do any drilling what so ever. We will go ahead and install our hardware. We are going to use this block and this bolt and we are just going to it in the frame. 00:20



Trailer Hitch Installation - 2006 Ford F-250 Super Duty

Today we are going to install part number 41931 from Draw-Tite, and we are going to install this hitch on a 2006 Ford F-250 Super Duty. We are looking at the passengers side frame rail here, and the hitch is going to get attached at this hole here, here, here and here. And you can tell by the whole area that the original factory hitch was on there already so we already took that off. The hitch is going to attach to the same place as the factory hitch did. This one will be a lot heavier hitch. And it will be identical on both sides. The factory wiring we took and just tucked it out of the way for now during our install. We will go ahead and reinstall that after the hitch is done.





Ford F-250 and F-350 Super Duty Trailer Hitch Questions and Answers


  • Proper Mounting Flange Orientation for the B&W Heavy-Duty Trailer Hitch Receiver # BWHDRH25230
  • The correct orientation for the mounting flanges for the B&W Heavy-Duty Trailer Hitch Receiver # BWHDRH25230 that you referenced is what the installation instructions show. They should point in and not out. I attached a picture that I took from the installation instructions, that are also attached to the right, that shows how the flanges should be orientated.
    view full answer...

  • Trailer Hitch Recommendation for a 2012 Ford F350 Dually
  • The tech tip for the Curt Hitch part # C15410 that you referenced that says, "Hitch fits vehicles with a 20 inch or smaller spare tire." is referring to the size of the rim. This hitch is confirmed to fit your truck so it should work well for you and will fit with your factory spare. If you are in the market for a new ball mount as well check out the link I attached that details how to pick out the correct one.
    view full answer...

  • Moving Valley Class III Hitch from 2007 Mercury Grand Marquis to 2011 Lincoln Town Car
  • Valley has gone out of business, which explains why you can't find them online. When it comes to the Hidden Hitch, Draw-Tite and the Curt hitches we offer, the 2007 Grand Marquis and the 2011 Town Car use the same hitch, so it would be a pretty good bet that a Valley hitch that fit a 2007 Grand Marquis would fit a 2011 Town Car. This being said, you'll need to replace the installation hardware. The nuts and bolts are intended for one-time use only, they're not meant to be torqued...
    view full answer...

  • Hitch Recommendation for a 2015 Chrysler Town and Country and Dodge Grand Caravan
  • Yes, the Curt Hitch part # 13364 that you referenced has been confirmed to fit your 2015 Chrysler Town and Country and Dodge Grand Caravan so I would recommend it for you. Check out the install video I attached. For trailer wiring you would want the part # C56150. I attached an install video for you to check out. For ball mounts I recommend the etrailer Ball Mount Kit # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip, and a carrying bag.
    view full answer...

  • Trailer Hitch for a 2002 Ford F-350 with Knapheide Utility Body
  • Usually they put utility bodies like the one on your 2002 Ford F-350 on the cab and chassis versions of the truck (rather than the standard models that would come with a regular bed). You would need to look at the hitches for the cab and chassis models linked to the right. These hitches fit a frame width of 34 inches. This is measured from the outside of one frame rail to the outside of the other frame rail. If your measurement is 34 inches then you would look at the cab and chassis...
    view full answer...

  • Hitch & Ball Mount for a 2013 Ford F-250 with 10-Inch Suspension Lift & 40-Inch Tires
  • Since your 2013 Ford F-250 Super Duty has an impressive lift in the suspension and 40 inch tires, the towing capacity will decrease to an unknown value. The hitch height measurement you provided, 33-inches from the top of the receiver tube to the ground, is too great a height to be compensated for by a ball mount with drop. The most drop available from a 2-1/2-inch Class-V hitch is 10-inches such as # DTALBM7025 (please see link at right). This means your trailer coupler's height would...
    view full answer...

  • Is Weight Distribution Recommended when Towing a 14,000 lb Trailer
  • Regardless of the capacity difference between using a WD system and not you would see a benefit to using a WD system for towing a trailer as heavy as yours. The lack of a capacity difference for the WD application does not indicate that you wouldn't benefit from the use of one. Any time the trailer weighs more than 50 percent of the tow vehicle a WD system is recommended. You would be within the capacity of your hitch to tow the trailer without a WD system, but you will have better handling...
    view full answer...

  • 2-1/2 Class V Hitch Recommendation for a 2000 Ford F-250 Keeps Spare Tire
  • The Draw Tite Titan Hitch part # 45297 would be exactly what you would need. This hitch will give you the 2-1/2 inch opening you need and will allow you to keep your spare. You will need to remove your factory hitch though. This product was specifically designed to work with the Titan Extender that came with your slide in camper like part # RP45292.
    view full answer...

  • Recommended 2-1/2 Inch Trailer Hitch for a 2003 Ford F-350 Super Duty Crew Cab Long Bed 4x4
  • Trailer hitch # 45014 is designed to fit certain years of cab and chassis models of Ford trucks. Cab and chassis models come without a bed, just a cab and chassis. They are later turned into service vehicles or fitted with flatbeds. If you have a regular 2003 Ford F-350 Super Duty this hitch will not fit because the frame spacing is too wide. For a regular 2003 Ford F-350 Super Duty you would use # 45297. I have linked a video showing an installation of this hitch for you. I also...
    view full answer...

  • Hitch Availability for a 2001 Ford E450 Shuttle Bus
  • I have a Class V hitch that would fit your 2001 E450 Chassis, part # 41945. However, due to the large overhang of your vehicle because of the shuttle bus portion of the vehicle it is kind of hard for me to say for certain. The best recommendation I can make would be for you to check out the install video and instructions and compare them to the rear frame of your vehicle to see if they would be compatible.
    view full answer...

  • Hitch and Extender Recommendation for a 2004 Ford Super Duty with Camper Installed
  • Yes you can use the Curt Hitch part # C15810 to tow your trailer with your setup. You will also need the Reese Titan Hitch Extender part # RP45292 to give you enough extension to tow a trailer with your 2004 Ford F250 that has a camper installed. This will install into the 2-1/2 inch hitch opening and will provide a 2 inch opening for a ball mount for your trailer.
    view full answer...

  • Trailer Hitch Recommendation for a 2006 Ford F250 Crew Cab
  • I would personally recommend going with the Curt Custom Fit Trailer Hitch Receiver, # C14355, for your 2006 Ford F250 Crew Cab. This hitch is specifically designed for your Ford F-250 and will bolt directly to your frame with no welding required. In order to be fully prepared to tow, you may also need Trailer Wiring, # C56032, and Ball Mount Kit, # EBMK2416.
    view full answer...

  • How to Figure Out How Low the Curt Hitch part # C15810 Would Sit Below Bumper
  • While I don't know exactly how far the Curt Hitch part # C15810 would hang below the bumper of your 2002 Ford Superduty I can tell you how you can figure it out. I went out into our warehouse and measured the distance from the mounting surface of the hitch down to the hitch opening and found that it measures 5-1/2 inches. So basically if you measure 5-1/2 inches down below the rear frame of your truck that is where your hitch opening will be.
    view full answer...

  • Trailer Hitch Recommendation for 2002 Ford F250 with Cowboy Bumper
  • Curt offers the Class V Trailer Hitch Receiver, # C15316, for your 2002 Ford F250 with a deep drop, aka cowboy, bumper. This hitch receiver is specially designed for heavy-duty towing with a tongue weight capacity of 2,400 pounds and a maximum gross trailer weight of 16,000 pounds. This hitch bolts directly to your truck's frame with no welding required. This hitch will only fit models with a 16 inch spare tire. We also offer the etrailer Ball Mount Kit, # EBMK2416, to use with the...
    view full answer...

  • Do you have to Know the Rear Axle Weight, Not Capacity, to Figure Out How Much a Truck Can Tow
  • Knowing the weight of the tow vehicle axle is not really relevant, or at most rarely relevant, to determining how much the truck can tow. What matters is the truck manufacturers axle capacity, gross trailer weight capacity, and gross combined weight rating. In my years of working in this industry I have never heard of the axle weight on the tow vehicle being needed to determine anything. Only the capacities. With that said I also asked around here to get some other opinions on the subject...
    view full answer...

  • What Hitch Allows Use of Extender to Clear Rear of Slide-In Camper in 1999 Ford F-350
  • It sounds like you need about 3-feet of additional length from your hitch to clear the back of your slide-in camper. There is a product to do this but it requires a specific brand of hitch; the Curt Class V hitch you referenced, part # C15410 is not suitable for this application. If your F-350 has a standard or step bumper you can use TorkLift Trailer Hitch # TLF1002 which is a dual-receiver Class V design. With this you can use the TorkLift SuperTruss Hitch Extension # TLE1536 that...
    view full answer...

  • Hitch Recommendation for a 2001 Ford F250
  • Deep drop bumpers will usually hang about 10 inches below the bottom of the frame where the hitch would attach to. If you measure that distance and its about 10 inches you would need a deep drop bumper hitch like Curt Hitch part # C15316. If you determine you do not have a drop bumper you could use the B&W Heavy-Duty Trailer Hitch Receiver # BWHDRH25230. For a ball mount, hitch ball, and pin and clip, I would recommend the etrailer Ball Mount Kit, part # 989900. This is a kit which...
    view full answer...

  • Why is there a Hole on the Side of Curt Trailer Hitch 15410 for a 2001 Ford F-250
  • I spoke with my contact at Curt about trailer hitch # C15410. The holes, one on each side near the bottoms of the brackets, are drain holes. The hitch is not painted or powder-coated. It goes through a dip process and the holes let the excess coating drain out. So the hitch actually looks the same on the inside as it does on the outside. My contact also wanted me to know that the hitch is made in Wisconsin so they build the hitches with the tough winters in mind. To complete your...
    view full answer...

  • When Using an Extension Would Upgrading the Factory Hitch Increase my Towing Capacity
  • Yes, the B and W Heavy Duty Hitch Receiver, # BWHDRH25230, on your 2008 Ford F250 would be strong enough to handle your boat as long as it's tongue weight is 1600 pounds or less when fully loaded. Just a reminder, you always want to follow the weight limitations of the component with the lowest rating. This also includes staying within the towing limits of your truck. I am estimating that your extension at 34 inches has a tongue weight rating of 450 pounds. If this is correct, upgrading...
    view full answer...

  • Will the Curt Hitch Part # C14355 fit a 2004 Ford F-250 with a Ranch Hand Bumper
  • More than likely the Curt Trailer Hitch part # C14355 would work on your 2006 Ford F250 with your Ranch Hand bumper as I checked with Ranch Hand and they state that their bumpers will let you retain your factory hitch. I checked with Curt and they told me that the # C14355 will install using your factory installation points. Looking at your pictures you might have to remove the hitch ball in your bumper.
    view full answer...

  • Trailer Hitch for a 2001 Ford F-350 Cab and Chassis Truck
  • If your 2001 Ford F-350 has the utility body then that means it was built on a cab and chassis model (originally did not come with a bed). Cab and chassis models have a more narrow frame width compared to regular pickup models. For a cab and chassis model and the same capacity hitch you would need # C15445. If you are not certain if you have a cab and chassis model or not you will need to measure the distance from the outside of one frame rail to the outside of the other frame rail....
    view full answer...

  • Can Loctite Threadlocker be Used when Installing Curt Trailer Hitch on a 2008 Ford F-250
  • To answer the last question first you could attach some quick links to the safety chain loops on Curt trailer hitch # C15410 so that they are compatible with smaller hooks. We have different size quick links and S-hooks depending on your needs and I have provided a link to them for you. For the trailer hitch installation hardware you can use Loctite such as # LT1330799 for a stronger bond or # LT37643 for a connection that can still be removed with hand tools. It is not required and...
    view full answer...

  • Weight Distribution System Recommendation for a 2002 Ford F250 Super Duty
  • For your setup you will definitely need a hitch with a higher capacity. The Curt Hitch # C15410 that you referenced would certainly have enough tongue weight capacity. However, you will still need to determine what the capacity of your vehicle is. If your owners manual says you have a lower capacity than the # C15410 then you need to abide by that as the overall capacity. When determining overall towing capacity you always need to go by the lowest rated component as the overall capacity. If...
    view full answer...

  • Will the Curt Trailer Hitch # C15810 fit 6-1/2 ft and 8 ft bed 2010 Ford F350s
  • Yes, the Curt Trailer Hitch # C15810 that you referenced will work on the 6-1/2 foot bed and 8 foot bed models of the 2010 Ford F350.
    view full answer...

  • Maximum Towing Capacity of the Curt Class V Trailer Hitch With or Without Weight Distribution System
  • I have confirmed with my contacts at Curt Manufacturing, and indeed the towing capacity of the Class V trailer hitch # C15410, is 17,000 pounds with or without using a weight distribution system. Therefore, the maximum towing weight of this trailer hitch is 17,000 pounds. Please check the towing capacity of your 2014 Ford F-250 or F-350, and make sure that it is rated appropriately for towing this capacity. Also please keep in mind that it is not recommended to exceed the lowest rated...
    view full answer...

  • Will Curt Class V Hitch # C15810 Fit a Ford F-250/F-350 With a Full Size Spare Tire
  • I spoke with my technical contact at Curt and he informed me that the Curt Hitch # C15810 will fit spare tires with a wheel size of less than 20 inches. We happen to have a Ford F-350 on site, so we checked out the spare tire underneath and it was a 275/70 R18, which is a full size spare tire for the vehicle and it has an 18 inch rim, so the Curt # C15810 that you are wanting would fit the truck we have here. If you check the tire size of your spare and it is under 20 inches, this...
    view full answer...

  • Trailer Hitch Safety Chain Connections for Reese Trailer Hitch # 45297
  • We have various safety chain quick links that you could use and then hook your safety chains to them. For example we have # 49135 at 1/2 inch diameter. I have also included a link to the other similar options and I am certain you can find one that will work for you.
    view full answer...

  • Weight Capacity of Curt Class V 2-1/2 Inch Hitch Receiver, Part # C15810
  • You are correct that the product description for the Curt Class V 2-1/2 Inch Hitch Receiver, Part # C15810, shows the same tongue weight and gross towing weight ratings with and without weight distribution. This is because unlike lower capacity hitches, say a Class III, this Class V hitch is already rated at or near the vehicle structural limits. Strictly speaking, adding a weight distribution setup would give this hitch receiver higher capacity, but it would serve no purpose. Unless...
    view full answer...

  • Dimensions of Curt Trailer Hitch # C14355 for 2004 Ford F-250 with Knapheide Body
  • After going out to our warehouse to make some measurements on the Curt Trailer Hitch # 14355, I have found the measurement from the center of the furthest bolt hole to the outer edge of the 2-inch by 2-inch receiver opening is 26-1/2 inches. The measurement from the center of the nearest bolt hole to the outer edge of the receiver opening is 13 inches. Finally, the measurement from the top of the hitch frame to the top edge of the receiver opening is 4-1/2 inches. I have included a...
    view full answer...

  • Will Draw-Tite Trailer Hitch 45297 Fit with a Full Size Spare Tire on a 2008 Ford F-350
  • We have a tech note that states that Draw-Tite trailer hitch # 45297 will fit the factory full-size spare on a 2008 Ford F-350. I have also included a link to the instructions which mention lowering the spare to install the hitch and then raising it back again once the hitch is installed. To complete your towing set up I recommend the etrailer ball mount kit # EBMK25318. It comes with a ball mount, a 2-5/16 inch ball, and a storage bag. For a hitch pin use # 74149. For trailer wiring...
    view full answer...

  • Will the Curt Hitch # C15445 fit a 2000 SRW Ford F350 Cab and Chassis
  • The CURT Trailer Hitch Receiver # C15445 that you referenced should work well for your 2000 Ford F-350 with a single rear wheel axle as this hitch is confirmed to fit all models of the 2000 Ford F350 cab and chassis. As long as the fuel tank is in the factory location it should not prove to be a problem either.
    view full answer...

  • How to Mount Existing 7-Way Connector on New Curt Hitch Receiver
  • We always suggest avoiding any drilling or alteration of a hitch if at all possible. We do offer a no-drill mounting bracket extension that attaches to a hitch with a steel ring clamp, but due to the very large size of the main tube on this hitch the supplied 12-inch ring clamp will not fit. You could adapt it to fit if you can find a ring clamp that is 15 inches or longer. We do not stock such a part, but if you can find one locally then this extension bracket, which is 3 inches wide...
    view full answer...

  • Hitch Recommendation for a 2000 Ford F250
  • Typically on deep drop bumpers the distance from the bottom of the frame to the bottom of the bumper is 10-12 inches. Since yours is only 7 inches you should be fine to use the CURT Trailer Hitch Receiver # C15410.
    view full answer...

  • What is a Deep Drop Bumper
  • A deep drop bumper is also known as a cowboy bumper. It is taller than a regular bumper, and would use a receiver that is lower than what would be used on the same vehicle that was equipped with a standard bumper. If you click on the provided link, you can see our Bumper FAQ article that will explain it in full. If your 1999 Ford F series has the cowboy bumper, the # C15316 would work great for you. If you have the standard bumper, # C14355 would be a better choice. This hitch will...
    view full answer...

  • Hitch Recommendation for a 1992 Ford F250 With a 10 inch Bumper
  • There are hitches available for your 1992 Ford F250. I would recommend you get a Hidden Hitch Trailer Hitch # 87471 if you do not have a deep drop bumper. This hitch will fit all model 1992 F250s and your 16 inch spare will fit with the hitch, but the spare tire cradle might require some adjustment for it to fit properly. To determine if you have a deep drop bumper check out the FAQ article I attached on types of bumpers. If you do have one you might be interested in purchasing...
    view full answer...

  • Factory Wiring Mounting Bracket is Relocated When Installing Trailer Hitch 45297 on 2012 Ford F-250
  • For the Draw-Tite trailer hitch # 45297, the instructions, which I have linked for you, state in step 8 that you will need to use the hole pattern from the electrical mount tab to drill new holes in the factory electrical bracket. You will need to use your own fastening hardware to secure it to the hitch. Basically, you are relocating the the harness mount. I have included a picture that points on the tab.
    view full answer...

  • Hitch Recommendation For 2011 Ford F-250 Super Duty Towing a Jayco 33RLDS Travel Trailer
  • There are two sizes of hitches you can install on your 2011 Ford F-250 Super Duty Diesel. There is a 2-inch receiver hitch and a 2-1/2 inch receiver hitch. The towing capacity on a 2011 Ford F-250 Super Duty Diesel will range from 12,500 lbs to 14,000 lbs depending on the model ( Regular Cab, Super Cab, or Crew Cab) of your vehicle. A 2-inch hitch would be sufficient enough for that towing capacity range. I would recommend the CURT Class V 2 Inch Hitch, part # C15410. This hitch...
    view full answer...

  • Availability of Hitches to Fit 2007 Ford F-250 With 20 Inch Spare and 10,000-Lb Towing Capacity
  • I spoke with my contact at Draw-Tite and he said the Draw-Tite Class IV 2 Inch Hitch, part # 41931, will fit your 2007 Ford F-250 with a 20 inch spare tire. The spare tire does need to be lowered when installing the hitch. This hitch is a Class IV 2 inch hitch with a maximum gross trailer weight capacity of 12,000 lbs. I am including a link to the installation instructions on the Draw-Tite hitch. I have the CURT Class V 2 Inch Hitch, part # C15410, that will fit with a 20 inch spare....
    view full answer...

  • Fit of Draw-Tite Class IV Part # 41943 on 2003 Ford F550 with 34-1/4 Frame Measurement
  • The Draw-Tite Class IV Hitch, part # 41943 will fit the rivet configuration you mentioned (see figure # 3 in the instructions I have linked to). I checked with one of my contacts at Draw-Tite, who tells me that this hitch will work with the 34-1/4 frame measurement. That 1/4 inch is within acceptable tolerances, so the hitch should fit just fine for you. You might also need the following: Ball Mount with 3 inch rise or 4 inch drop, part # 40331 2 inch trailer ball, part # A-90 2-5/16...
    view full answer...

  • Will Curt Trailer Hitch Receiver # C15810 Fit Around OEM Spare on 2001 Ford F-250
  • To install the Curt Trailer Hitch Receiver, part # C15810, on your 2001 Ford F-250, you will need to temporarily lower the spare tire. You will be able to re-install the spare tire after installation of the hitch. Yes, the hitch will fit with your OEM spare tire. I have linked instructions for the Curt Trailer Hitch Receiver, part # C15810 and an FAQ on trailer hitch installation tips.
    view full answer...

  • Reese Trailer Hitch # 45297 Recommendation for a 2002 Ford F-350
  • I would recommend the Reese Trailer Hitch, part # 45297, for your 2002 Ford F-350 Super Duty. This hitch will fit with the factory spare tire and will be able to tow up to 18,000 lbs of gross trailer weight. I attached installation instructions for this hitch. You may be interested in purchasing a Reese Titan Ball Mount for 2-1/2 inch Receivers, part # RP45322, a Hitch Ball with 2 inch Diameter and Medium Shank, part # A-90, and a Hitch Ball with 2-5/16 inch Diameter and Medium...
    view full answer...

  • Will Camper Tie Downs that Attach to Factory Hitch on 2000 Ford F-250 SD work on Aftermarket Hitch
  • On your 2000 Ford F-250 SD, the camper tie downs used for the factory hitch will usually be different than the tie downs used for an aftermarket hitch like the Reese Titan Class V 2-1/2 Inch Hitch, part # 45297. The front camper tie downs will be the same since the attachment of the front tie downs is to the frame. I checked the Torklift brand camper tie downs that I carry and it list the rear tie down for the factory hitch as being different than the rear tie down for the aftermarket...
    view full answer...

  • Trailer Wiring Mounting Options for Curt Trailer Hitch # 15601 on a 2010 Ford F-250
  • For the Curt Trailer Hitch, # 15601, for the 2010 Ford F-250, we have several trailer wiring connector mounting brackets that you could use. First, for a basic 4-Way flat, you can use bracket # 18144 and No-Drill Mount Bracket, Short, # 18140, or No-Drill Mount Bracket, Long, # 18136. For a 7-Way, you can use either the short or long No-drill bracket, mentioned above, and Mounting Bracket, # PK12711U. Another option for the 7-Way would be 7-Way Trailer Connector Mounting Box, # 18159....
    view full answer...

  • Is There Drilling Required to Install a Titan Trailer Hitch, part # 45297, in a 2010 Ford F250
  • There is no drilling to the frame or body of your 2010 Ford F250 to install a Titan Trailer Hitch Receiver - Custom Fit - Class V - 2-1/2 inch, part # 45297. You will need to drill the electrical plug mounting bracket on your truck to allow you to mount it to the Titan hitch. Basically, other than that you will just need to temporarily remove the spare tire and bolt it into place. You may also be interested in purchasing the following: Reese Titan Ball Mount for 2-1/2 inch Receivers,...
    view full answer...

  • Recommendation for a Trailer Hitch for a 1999 Ford F-350 Towing a 7,000 Pound Trailer
  • If you can let me know the Year and the specfic model of your Ford F-350 1 Ton Truck I would be glad to make a recommendation for you. The hitch you referenced # 87480 is only capable of 5,000 pounds weight carrying so you would need to use a weight distribution system, see link, with this hitch to tow a 7,000 pound trailer. With the specific year make and model I can try to find a hitch that will install with the under body mounted spare, as long as it is not larger than the standard...
    view full answer...

  • What Size Spare Tire Will Fit With Curt Hitch on 2011 Ford F-250 Super Duty
  • I contacted our representative at Curt and he informed me that the Curt Trailer Hitch Receiver, part # 14041, will not fit vehicles with a 20 inch wheel spare. So if the vehicle has a 20 inch tire, for example 245/55/20, it will not fit that vehicle. The 20 inches is referring to the diameter of the wheel, since the wheel is 20 inches in diameter and will require a tire with a larger diameter than tires for smaller wheels. Since you have an 18 inch wheel and 18 inch tire size, the Curt...
    view full answer...

  • Does Curt Trailer Hitch for a 2005 Ford SuperDuty Have a Specific Torque Rating for Hardware
  • Yes, the proper torque setting will be stated in the instructions with the hitch. Always make sure to follow the instructions that came with your particular hitch as manufacturers will change hardware from time to time so torque ratings can vary even on the same hitch model. I have included a link to the instructions to the right.
    view full answer...

  • How Can I Attach My OE Electrical Bracket to the New # C15410 Trailer Hitch
  • To relocate the 7-Way electrical connection on your 2006 Ford F-350 you can use the Mounting Bracket for Pollak 7-Pole, RV-Style Trailer Connector - Vehicle End, item # PK12711U, and a no drill bracket, item # 18136, as long as the 7-Way is similar to the Pollak Replacement 7-Pole, RV-Style Trailer Connector Socket, item # PK11893. We have a video (see link) of a hitch install on a 2006 Ford F-250 that shows, at the end of the video, the relocation of the 7-Way connector. If you have...
    view full answer...

  • Class V Trailer Hitch Options for a 2002 Ford F-250 Super Duty 4x4 Lariat
  • We have numerous Class V hitch options for your 2002 Ford F-250 Super Duty. I have listed them below. Curt Trailer Hitch, # C15410 2 inch receiver Curt Trailer Hitch, # C15810 2-1/2 inch receiver Draw-Tite Trailer Hitch, # 45297 2-1/2 inch receiver B&W Heavy-Duty Hitch, # BWHDRH25230 2 inch receiver Tork Lift Trailer Hitch, # TLF1002 2 inch receiver Tork Lift Trailer Hitch, # TLF1002-30 2-1/2 inch receiver I have included links to the instructions for the hitches below. You can...
    view full answer...

  • Trailer Hitch, Extension, Accessories for 2002 Ford F-350 With Slide-in Camper and 16 Foot Trailer
  • We do have products that will fit your 2002 Ford F-350 and provide the clearance past the end of the camper. The problem is that with a hitch extender, and a super extra long ball mount, your hitches tongue weight capacity might be so drastically reduced that you will not be able to tow your cargo trailer. But, everything changes if you were to use the Titan Trailer Hitch Receiver Hitch, # 45297. This guy is a Class V hitch, capable of 18,000 pounds of gross trailer weight. Tongue weight...
    view full answer...

  • What Deep Drop Bumper Hitches are Available for a 1999 Ford F-250 with at 1,000 Lb. Tongue Capacity
  • The weight capacities for the # 41535 hitch are as follows: Weight Carrying Capacity Max Gross Trailer: 6,000 Pounds Max Tongue: 600 Pounds Weight Distribution Capacity Max Gross Trailer: 10,000 Pounds Max Tongue: 1,000 Pounds The hitch is designed for use with deep drop bumpers, which I assume is why it was used. We have a hitch available for a deep drop bumper on a 1999 Ford Super Duty that has a tongue weight capacity of 1,000 pounds or more and a gross trailer weight of...
    view full answer...

  • Can a Class 5 Titan Hitch Be Used to Safely Tow with a 24 Inch Hitch Extender, 2004 Ford F-350
  • Using an extension will reduce hitch capacity, so using a larger, stronger hitch could be very helpful. The Class V Titan hitch you were looking at is for GM and Chevy trucks, so you would need a different part number. The largest capacity hitch we have for your 2004 Ford F-350 is for 18,000 pounds gross trailer weight and have a maximum tongue weight of 2,000 pounds, 2,500 pounds with weight distribution equipment. It is Draw-Tite part # 45297. The hitch will require you to remove the...
    view full answer...










Stay Connected


Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email






etrailer.com reviewsetrailer.com reviews

All images, layout and content copyright etrailer.com