View Cart


2014 Hyundai Tucson Accessories

change vehicle




2014 Hyundai Tucson Videos

Trailer Wiring Harness Installation - 2014 Hyundai Tucson

Today on our 2014 Hyundai Tucson, we're going to review and install the Curt wiring kit with 4 pole trailer connector. Part number 56146KIT. To begin our install, we're first going to go ahead and remove the rear tail lights. To remove the rear tail lights, we'll open up the hatch, and remove the two screw fasteners on each side that secure it. Once we have the two screws out, we'll go ahead and push the tail light assembly to the rear of the vehicle, popping it free from it's fasteners underneath. We'll pull the tail light assembly out. We can see the alignment pins underneath, we want to be careful not to break as we're removing it. Next, we're going to go ahead and remove the electrical connector from the back of the tail light assembly. To do that, we'll press on the locking tab, and separate the two.



Trailer Hitch Installation - 2014 Hyundai Tucson - Curt

Today on our 2015 Hyundai Tucson, were going to review and install the CURT Class III 2 Receiver Tube Hitch part number C13120. Here is what our hitch is going to look like once installed. As you can see, this is a really well-concealed hitch as our cross tube is hidden behind the rear fascia. What you can see is the receiver tube which is a nice fully-welded construction with a black powder-coated finish. This is our Class III 2 x 2 receiver tube. Weve got our chain hold down on each side and a pre-drilled 5/8th pinhole. This is capable of up to 525 pounds of tongue weight with a 3,500-pound tow capacity.



Trailer Hitch Installation - 2014 Hyundai Tucson - Curt

Today on our 2014 Hyundai Tucson we're going to review and install the CURT class three 2" receiver tube hitch, part number C13066. Here's what our hitch looks like once it's installed. As you can see, the main crosstube of our hitch is hidden nicely behind the rear fascia, so the only thing we really have exposed is our receiver tube, which is a fully welded construction, and a nice black powder-coated finish. This is our class three 2" by 2" receiver tube. We've got our chain hold down on each side and the pre-drilled 5/8 pinhole. Hitch itself is capable of up to 350 pounds of tongue weight and a 3,500 pound tow capacity. Next we'll give you a couple measurements to assist you with selecting accessories for your new hitch.



Trailer Hitch Installation - 2014 Hyundai Tucson - Curt

Today on our 2014 Hyundai Tucson we're going to review and install the CURT class two 1-1/4" receiver tube hitch, part number C12030. Here's what our hitch is going to look like once it's installed. As you can see, it's a really nice designed hitch as the majority of our crosstube is hidden behind the rear fascia. The only thing really exposed is our fully welded constructed black powder-coated receiver tube. On each side of the receiver tube is our chain hold down and the pre-drilled 1/2" hole. The receiver tube itself is a 1-1/4" by 1-1/4" class two inch hitch, which means it's capable of up to 350 pound of tongue weight and a 3,500 pound tow capacity. Next we'll go ahead and give you a couple measurements to assist you with selecting accessories for your new hitch.



Trailer Wiring Harness Installation - 2014 Hyundai Tuscon

Today on our 2014 Hyundai Tucson, we'll be installing the Curt T-connector vehicle wiring harness with a 4-pole flat trailer connector, part number 56101. First, we'll open up the rear hatch. Then, starting on the driver side, we'll remove the two fasteners that secure the tail light housing. Remove the fasteners and then we're going to go ahead and pop the tail light housing free. Be careful not to break the alignment tabs underneath. Now, we can disconnect the manufacturers wiring that goes into the back of the tail light assembly, removing the connector from the socket. To do that, we'll press on the locking tab, removing the connector. Then, we'll go ahead and set tail light assembly aside.



Trailer Hitch Installation - 2014 Hyundai Tucson - Hidden Hitch

Today on our 2014 Hyundai Tucson, we'll be installing Hidden Hitch, part number 87612. Note this is what our hitch will look like once installed. Next, we'll go ahead and give you a couple measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is five inches. From the top of the receiver tube opening to the ground is 13 and a quarter inches. This will assist you in selecting accessories such as a ball mount, bike rack, or cargo carrier. Now we'll go ahead with installation. To begin our install, we'll first need to lower the exhaust.



Trailer Hitch Installation - 2014 Hyundai Tucson - Draw-Tite

Today, on our 2014 Hyundai Tucson, we'll be installing the Draw-tite hitch, part number 75717. Note, this is what our hitch will look like once installed. Next, we're going to do a couple of measurements to assist your selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is five inches. From the top of the receiver tube opening to the ground is thirteen and a quarter inches. This will assist you in selecting accessories, such as a ball mount, bike rack, or cargo carrier. Now, we'll go ahead with installation. To begin our install, we'll first need to lower the exhaust.





2014 Hyundai Tucson Questions and Answers


  • How to Bleed Trailer Brakes with the Atwood Actuator # AT82543
  • The easiest way for me to explain how to bleed the brakes is to have you check out the video I attached that shows the method we use here to bleed trailer brakes. To actuate the actuator to move the fluid through the lines on your coupler you could use a large pair of vice grips to attach to the front of the ball coupler and then use the leverage the vice grips create to push in slowly.
    view full answer...

  • Trunk Mount Bike Rack Recommendation for a 2014 Hyundai Tucson
  • I checked with Thule and there are some trunk mount bike rack fits for your 2014 Hyundai Tucson. I recommend the Raceway 2, # TH9001PRO. It is the 2-bike version of the Raceway 3, # TH9002PRO that you referenced. (The Raceway 3 is also a fit.) What makes the Raceway bike racks so great is the 4 retractable cables it uses instead of 6 straps like other racks. The cables store inside the rack and are more durable and sturdy than straps. And since there are just 4 of them it makes installation...
    view full answer...

  • Trunk Mounted Bike Rack Recommendation for a 2014 Hyundai Tucson
  • According to Yakima, the KingJoe Pro 2, # Y02624, will fit your 2014 Hyundai Tucson. I have included a link to a video review of this rack for you. If you will be carrying any bikes that do not have a top frame bar that goes straight across from handle bars to seat post, I recommend adding the Bike Adapter Bar, # Y02531, to carry the bikes more level. I have included a video of this adapter also.
    view full answer...

  • What is the Usable Length of the Rola Crossbars for the 2014 Hyundai Tucson
  • I spoke to my contact at Rola and he informed me that the bars of the Rola Sport Series Roof Rack part # 59870 that you referenced are not adjustable. The distance between the crossbars will be 700 millimeters. The front crossbar will be longer than the rear. The usable portion of the front crossbar is 910 millimeters and the rear is 872 millimeters.
    view full answer...

  • Recommended Roof Rack System for 2014 Hyundai Tucson with Naked Roof
  • We offer a number of roof racks for the 2014 Hyundai Tucson with a naked roof. The link provided will take you to our fitguide page for Tucson roof racks for compatible roof racks. Systems are available from a number of manufacturers and with several types of crossbars (round, square, elliptical and aerodynamic). Since your Tucson has a naked roof a good cost-effective round crossbar rack is the Rola rack, part # 59730. For another high quality, inexpensive option check out the...
    view full answer...

  • Roof Rack and Kayak Carriers for a 2014 Hyundai Tucson with Panoramic Roof and Raised Side Rails
  • Since your 2014 Hyundai Tucson GLS has the factory raised side rails, you can install a roof rack even with the panoramic roof. You just would not necessarily be able to open the roof with the rack installed. Rola roof rack # 59870 that you are interested in will fit your Tucson. There are a few different kayak carriers that you will be able to use with this rack that I recommend. I have listed them below: SportRack carrier # SR5511 SportRack carrier # SR5513 Thule Hull-A-Port #...
    view full answer...

  • Would the Pro Series Eclipse 4 Bike Rack # 63124 fit a 2014 Hyundai Tucson
  • The Pro Series Eclipse 4 Bike Rack # 63124 that you referenced is designed to fit 2 inch hitches. So as long as you have a 2 inch hitch like the Curt Hitch part # C13120 installed on your vehicle it would work well. I attached review videos for both products for you to check out. If you plan on carrying any womens or alternative framed bikes without horizontal top tubes you may also be interested in purchasing a Swagman Easy-Out Women's and Alternative Frame Bike Adapter # 64005 to provide...
    view full answer...

  • Will Kuat Sherpa 2-Bike Platform Carrier # S101 Fit on a 2014 Hyundai Tucson
  • The 2014 Hyundai Tucson can be fitted with either of two sizes of hitch receiver, a 1-1/4-inch Class II or a 2-inch Class III hitch. The Kuat Sherpa 2-Bike Platform Carrier # S101 is designed to work with both types so it will definitely fit the hitch on your Tucson. You can take one simple measurement to confirm that this carrier will fit satisfactorily at the rear of your vehicle and provide enough room for your bikes without interfering with the back of the car. Simply measure from...
    view full answer...










Stay Connected


Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email






etrailer.com reviewsetrailer.com reviews

All images, layout and content copyright etrailer.com