2012 Ford Expedition Accessories

2012 Ford Expedition Questions and Answers

Cargo mat for a 2012 Ford Expedition from 2nd Row of Seats to the Back Over Folded 3rd Row
For your 2012 Ford Expedition you can use Husky Liners cargo mat # HL23571 which will fit from behind the 2nd row, over the folded down 3rd row, to the back of the vehicle. This mat fits if the vehicle has a 2nd row bench seat or buckets with or without center console. It is also available in tan, # HL23573, and gray, # HL23572. We also have WeatherTech cargo mat # WT40222 with the same fits as those listed above. For gray use # WT42222 and for tan # WT41222. If you have an EL model for ta
view full answer...

Trailer Brake Controller Recommendation for a 2012 Ford Expedition with Factory Tow Package
There basically two types of brake controllers: time delay and proportional. Time delay controllers, like # 39523 that you have referenced, send back a pre-set amount of voltage over a certain amount of time which can be adjusted. It can take some time determining the best set up for any given trailer when using a time delay controller and there is more wear and tear on both the vehicle and the trailer. The benefit is that time-delay controllers do not have many mounting restrictions. Proport
view full answer...

Will a X Cargo 20 Cargo Box Fit on a 2012 Ford Expedition
The X Cargo Thule Box is designed to be used on most factory and aftermarket cross bars. The u-bolt that comes with the X-cargo is 4 inches wide so it should fit around a wide variety of cross bars. If you do not have a roof rack with cross bars that run from one side to the other you will need to check out the link I attached that will take you to the Thule roof racks that are available for your vehicle.
view full answer...

Will the Oklahoma State University 2 in Hitch Cover fit the Factory Hitch of a 2012 Ford Expedition
Yes, this Oklahoma State University Chrome Logo State Emblem 2 inch Hitch Cover # AMG100444 that you referenced will fit the hitch on your 2012 Ford Expedition. The hitch on your vehicle will have a receiver opening that will measure 2 inches across. That is the exact hitch size that the # AMG100444 is designed to work on. You may also be interested in a Pin and Clip # PC3 to secure the hitch cover into your hitch. Or, since hitch covers are pretty easily stolen you may be interested in pu
view full answer...

Weight Distribution System for a 2012 Expedition Hauling 2 Horse Trailer with 7000 lbs GVW
The most important thing to consider when choosing a weight distribution system is the tongue weight of your trailer when it is fully loaded and ready to tow. Anything loaded behind the rear axle in your 2012 Ford Expedition will contribute to the tongue weight as well. I have attached an article that explains how to determine the tongue weight of your trailer. When choosing a weight distribution system, you should choose a system that has a tongue weight range that encompasses the tongue we
view full answer...

How to Tap into Transmission Fluid Return Line on a 2012 Ford Expedition for a Transmission Cooler
The line that you will need to tap into is the transmission fluid return line. The easiest way to determine the return line on your 2012 Ford Expedition transmission is to start the truck, shift into drive but do not go anywhere. After about 15 seconds or so put the truck back in park and apply the emergency brake. Turn off the truck. Out of the 2 hoses attached to the transmission, one should be warmer than the other. The one that is cooler is the return line. You can use radiator adapter fi
view full answer...

Coil Sumo Spring Application for 2012 Ford Expedition 4WD
According to the kind folks at Super Springs, the Coil Sumo Springs you mentioned # CSS-1168R will work on either the 2WD or 4WD models. It would work very well on your 2012 Expedition. To see the installation details, click on the provided link.
view full answer...

Installing Brake Controller on 2012 Ford Expedition
The 3035-P is the correct Brake Controller Wiring Adapter for your Expedition. The under dash connector will be gray in color, and can be found behind and to the right of the OBD port, as shown in the installation video I have linked you to. Although the existing plug has 6 terminals, only 4 of them are used. If your Expedition is equipped with the factory 7-way trailer connector, once the controller is plugged in and mounted to the underside of the dash, the install will be complete. If y
view full answer...

Location of Factory Brake Controller Port on a 2012 Ford Expedition
I spoke with my contact at Tekonsha and they said they have not done a test fit of a brake controller on a 2012 Ford Expedition, but they do not believe it to be any different than the 2011 model. If the 2012 Expedition is the same as the 2011 model, then the factory brake controller port plug will be located under the dash to the right of the steering wheel. It will be a 6-pin rectangular connector that is normally gray. It may be tucked up and out of the way. I am including a link to a vide
view full answer...