2009 Honda CR-V Accessories

SportRack Escape 3 Hitch Bike Rack Review - 2009 Honda CR-V

Today, on this 2009 Honda CRV, we are going to attest Part number A30403 from Sportrack. Couple things to know, that this bicycle rack will work with 1-1/4 receiver hitches, class-two only. This will also work with a class-three receiver hitch, with the included spacer. All right, we'll start off our test fit by installing the bike rack into the hitch. Then, we'll tighten down the anti-rattle ball and install the safety clip on the other side. Then, we'll go ahead ang get some clearance measurements.

Yakima DoubleDown Ace Hitch Bike Rack Review - 2009 Honda CR-V

**Please note: I stayed with part number y02451 in the file name and in the transcription since that is how the customer wanted the file named, but the audio refers to part number y02452. Please delete this message before sending to the client.** Alright, today on this 2009 Honda CRV, were going to do a test fit of part number y02451, from Yakima. This is a Doubledown Ace 5 Bike Rack. A few things to know about this bike rack: it can work with one-inch-and-a-quarter receiver hitches, both class one and class two; however, with a class one receiver hitch, youre limited to carrying just two bicycles. Now, this will also work with a two-inch receiver hitches with the provided spacer. Well start off the test fit by installing the bike rack into the hitch.

Surco Hitch Cargo Carrier Review - 2009 Honda CR-V

Alright, today on this 2009 Honda CRV, were going to do a test fit of part number 52018, from Surco. This is our 24x60 cargo carrier. Alright, a couple of things to know: this is a cargo carrier designed for two-inch receiver hitches only; it has a 500 pound capacity or the limit of the receiver hitch; and, its created from a steel design with a powder coat finish. Now well start out the test fit by installing the carrier into the hitch. Then well go ahead and install the hitch pin and clip. Then, well go ahead and get a few clearance measurements.

SportRack EZ Hitch Bike Rack Review - 2009 Honda CR-V

Today on our 2009 Honda CRV, were going to do a test fit of part number a30901, from Sportrack. A few things to know about this bicycle rack: it will work with engine quarter receiver hitches, both class one and class two; it will also work with two inch receiver hitches, with the included spacer. Well start out our test fit by installing the bike rack into the hitch. Then Ill tighten down the anti-rattle bolt and put the safety pin on the other side. Then well go ahead and get some clearance measurements. Clearance from the bicycle rack to the hitch will be about 10 inches.

Rola Hitch Cargo Carrier Review - 2009 Honda CR-V

Today on our 2009 Honda CRV, were going to do a test fit part number 59502 from Rola. This is a hitch cargo carrier. A few things to know about this cargo carrier are that it is designed for two-hitch receiver hitches only. It has a capacity for 600 pounds or lower limit of your hitch. The shank is also raised to give you a little bit better ground clearance. Well start off to test it by installing the cargo carrier in to the hitch, and then installing the pin and clip.

Pro Series Hitch Cargo Carrier Review - 2009 Honda CR-V

Today on our 2009 Honda CRV, were going to test fit part number 63153 from tow-ready. This is a 24x60 cargo carrier. A few things to know about this cargo carrier is that it has a raised shank that elevates the carrier platform for a little bit better ground clearance. Its constructed from steel with a black powder coat finish. The weight capacity of this cargo carrier is 500 pounds. Also, this cargo carrier is designed for two-hitch receiver hitches only.

Rain-X Latitude Wiper Blades Installation - 2009 Honda CR-V

Today on this 2009 Honda CRV were going to do a test fit of part number RX5079281 from Rain-X. This is a latitude windshield wiper blade. The passenger side will be a different size and that would be part number RX5079283. To start off our test fit well go ahead and remove the original blades first. Theres a small tab that we can push then we can go ahead and slide off the original blade. Now the new windshield wiper blade slides right into place.

Trailer Hitch Installation - 2009 Honda CR-V - Draw-Tite

Today on this 2009 Honda CR-V, were going to install part number 75547 from Draw-Tite. This is what the hitch looks like once it's installed on the vehicle. Next, well be using the measurements that will help you out in selecting some accessories such as the ball mount, a bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground will be 15-3/4 inches and from the center of the hitch pin hole to the edge of the bumper will be about 2 inches. Now, well go ahead and show you how the hitch is installed. First thing you need to do is go ahead and lower the exhaust.

Yakima StickUp 2 Hitch Bike Rack Review - 2009 Honda CR-V

Today on our 2009 Honda CRV were going to be test fitting the Yakima StickUp 2 Hitch Mounted Bike Carrier, part number Y02420. To mount this carrier to our vehicle well insert the shank into the receiver tube of our hitch. Line up the hitch pin holes and then well thread in our anti-rattle bolt and tighten it with a wrench. Weve got about 13 inches of clearance from the bottom of the carrier to the ground. Weve got about 4 inches of space between the closest part of the bike rack and the closest part of the vehicle. Overall weve added about 14-1/2 inches of length to the rear of our vehicle.

Thule Vertex 4 Hitch Bike Rack Review - 2009 Honda CR-V

Today we have with us a 2009 Honda CRV and were going to be test fitting the Thule Vertex 4 Hitch Mounted Bike Carrier, part number TH9029. To fit our bike rack on our vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well line up the hitch pin holes, thread in our anti-rattle bolt and tighten it down with a wrench. Once weve done that were going to check first for rear vehicle access. Well grab the quick release lever at the bottom of the carrier to fold it down. Well open the cargo door of our CRV and make sure we can still access the cargo area.

Thule T2 Platform Style Hitch Bike Rack Review - 2009 Honda CR-V

Today on our 2009 Honda CRV were going to be test fitting the Thule T2 Platform Style Bike Carrier part number TH916XTR. To mount the carrier to the vehicle well insert the shank of the carrier into our receiver tube. Well line up the hitch pin holes, thread in our anti-rattle bolt and tighten it down with a wrench. Once weve done that well go over some clearance measurements. Weve got about 12-1/2 inches of ground clearance from the bottom of the bike rack to the ground. Weve got about 4 inches of clearance from the closest part of the bike rack to the closest part of the vehicle and we added about 16 inches of length to the rear of our vehicle.

Thule Parkway 2 Hitch Bike Rack Review - 2009 Honda CR-V

Today on our 2009 Honda CRV were going to be test fitting the Thule Parkway 2 Hitch Mounted Bike Carrier part number TH958. To mount the carrier to our vehicle were going to insert the shank of the carrier into the receiver tube of our hitch. Well line up the hitch pin holes, feed in our anti-rattle bolt and tighten it down. Once we have done that were going to check for rear vehicle access. Well remove the pin at the base of the bike rack and tilt it down to make sure we can still open the cargo door of our CRV. Now well tilt the bike rack back up and go over some clearance measurements.

Thule Hitching Post Pro Hitch Bike Rack Review - 2009 Honda CR-V

Today we have with us a 2009 Honda CRV and were going to be test fitting the Thule Hitching Post Hitch Mounted Bike Carrier part number TH934XTR. To mount the carrier to our vehicle were going to insert the shank into the receiver tube of the hitch. Well line up, thread in our anti-rattle bolt and tighten it down. Next well check for rear vehicle access. Well remove the pin at the base of the bike rack and tilt it down. Well open the hatch of our CRV and make sure we can still access our cargo area.

Thule Helium Hitch Bike Rack Review - 2009 Honda CR-V

Today on our 2009 Honda CRV were going to be test fitting the Thule Helium Aluminum Bike Carrier part number TH970XT. To mount this carrier to our vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well line up the hitch pin holes and then well use the hand knob to tighten our bike carrier. Well then take the safety pin and insert it to our hitch pin hole. Next well check for rear vehicle access. Well grab the release lever at the base of the bike rack and tilt it down.

Thule Apex 4 Swing Hitch Bike Rack Review - 2009 Honda CR-V

Today on our 2009 Honda CRV were going to be test fitting the Thule Apex Swing 4 Hitch Mounted Bike Carrier part number TH9027. To mount our carrier to the vehicle first well insert the shank of the carrier into the receiver tube of our vehicle. Well push it in until the automatic hitch pin closes in our hitch pin hole and then well tighten the anti-rattle device with the hand knob. Next well go over some clearance measurements. Weve got about 6 inches of clearance between the closest part of the bike carrier and the closest part of the vehicle. Weve got about 13 inches of ground clearance from the bottom of the bike rack to the ground.

Thule Doubletrack Hitch Bike Rack Review - 2009 Honda CR-V

Today on our 2009 Honda CRV were going to be test fitting the Thule Double Track Hitch Mounted Bike Carrier part number TH990XT. To mount this carrier to our vehicle well insert the shank of the carrier into our receiver tube of our hitch. Well line up the hitch pin holes and then thread in our anti-rattle bolt and then tighten it down with a wrench. Next well go over some clearance measurements. We have about 12 inches of ground clearance from the bottom of the bike rack to the ground. Weve got about 4 inches of clearance between the closest part of the bike carrier and the closest part of the vehicle.

Thule Apex 4 Hitch Bike Rack Review - 2009 Honda CR-V

Today on our 2009 Honda CRV were going to be test fitting the Thule Apex 4 Hitch Mounted Bike Carrier part number TH9025. To mount our carrier to the vehicle were going to hold open the automatic hitch pin. Well fit the shank of the carrier into the receiver tube of our hitch. Well release the automatic hitch pin and let it snap into place in our hitch pin hole then well use the hand knob to tighten down the anti-rattle device securing our bike rack to the vehicle. Next were going to check for rear vehicle access. Well pull the quick release lever at the base of the bike rack and let it tilt down.

Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2009 Honda CR-V

Today, on our 2009 Honda CRV, were going to be test fitting the Swagman XTC2 hitch-mounted bike carrier, part number s64670. To mount our carrier to the vehicle, were going to insert the shank of the carrier into the receiver tube of the hitch. Well line up the hitch pin holes, thread in our anti-rattle bolt and use a wrench to tighten it down. Next, were going to go over some clearance measurements. We have 13 inches of ground clearance from the bottom of the bike rack to the ground. We have 7 inches of clearance between the closest part of the vehicle and the closest part of the bike rack.

Rhode Gear Highway Hitch Bike Rack Review - 2009 Honda CR-V

Today on our 2009 Honda CRV were going to be test fitting the Rhode Gear Highway 2 Hitch Mounted Bike Carrier part number RG8015220. To mount this carrier to our vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well line up the hitch pin holes then well thread in our anti-rattle bolt and tighten it down with a wrench. Next were going to go over some clearance measurements. We have 11-1/2 inches of ground clearance from the bottom of our bike rack to the ground. Weve got about 9 inches of clearance between the closest part of our bike rack and the closest part of our vehicle.

Pro Series Q-Slot Hitch Bike Rack Review - 2009 Honda CR-V

Today on our 2009 Honda CRV, were going to be test fitting the Pro Series Q-Slot Hitch-Mounted Bike Carrier, part number PS63134. To mount our bike rack to our vehicle, were going to insert the shank of the bike rack into the receiver tube of our hitch. Well line up the hitch pin holes and secure our bike rack with a hitch pin. Next, well check some clearance measurements. Well take the two arms of the wheel trays and pull them down flat. We have about 13 inches of ground clearance from the bottom of the bike rack to the ground.

Pro Series Eclipse 4 Hitch Bike Rack Review - 2009 Honda CR-V

Today on our 2009 Honda CRV, were going to be test fitting the Pro Series Eclipse 4 Hitch-Mounted Bike Carrier, part number 63124. To mount our carrier to the vehicle, well insert the shank of the carrier into the receiver tube of our hitch. Well line up the hitch pin holes, feed in our anti-rattle bolt and tighten it down. Next, were going to go over some clearance measurements. Weve got about 12-3/4-inch clearance from bottom of the bike rack to the ground. Weve got about 6-1/2 inches of space between the closest part of the bike rack and closest part of the vehicle.

Trailer Hitch Installation - 2009 Honda CR-V - Hidden Hitch

Today, on our 2009 Honda CRV, were going to be installing the Hidden Hitch, part number 87440. This is what our hitch will look like once its installed. Next, well go ahead and give you a couple measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost side of the bumper is going to be 2 inches. From the top of the receiver tube to the ground is 14 inches. This will assist you in selecting accessories such as a draw bar, a bike rack or cargo carrier.

Trailer Hitch Installation - 2009 Honda CR-V - Curt

Today in our 2009 Honda CRV were going to be installing Curt Hitch, part number 13555. This is what our hitch would look like once its installed. Next, well go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 2 inches. From the top of the receiver tube to the ground is 14-3/4 inches. This will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier.

Trailer Hitch Installation - 2009 Honda CR-V - Curt

Today on our 2009 Honda CRV, were going to install the Curt Hitch, part number 11555. This is what our hitch will look like once its in place. Next, well go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 6 inches. From the top of the receiver tube to the ground is 12-1/4 inches. This will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier.

Trailer Hitch Installation - 2009 Honda CR-V

Today on this 2009 Honda CR-V we are going to be installing Draw-Tite hitch part number 24792. This installation will also apply for Hidden Hitch part number 60869. We are underneath the vehicle and before we get started pointing out the mounting holes for the trailer hitch we want to lower the exhaust off the passenger side frame rail. There are two hangers that we need to lower the exhaust off of. They are both here at the rear side of the exhaust system. To remove the exhaust off its hangers we just want to take a spray lubricant and spray down the studs. Then we can take either a set of pliers or a pry bar and pry it off the stud. We can just let the exhaust rest on the cross bar. 00:37