Free Shipping on Orders Over $99
Front Mount Hitch
Base Plate for Tow Bar
Vehicle Tow Bar Brake System
Vehicle Tow Bar Wiring
Spare Tire Bike Racks
Performance Chip Tuners
Throttle Body Spacer
Vehicle Snow Plows
Vehicle Engine Heaters
Side Window Vents
Vehicle Seat Covers
Windshield Wiper Blades
Trailer Wiring Harness Installation - 2006 Jeep Liberty
SMI Stay-IN-Play DUO Braking System Installation - 2006 Jeep Liberty
Today, on a 2006 Jeep Liberty, we're going to show you part number SM99251. This is an SMI Stay-In-Play DUO supplemental braking system. We'll go ahead and cover some of the components of the SMI DUO Stay-In-Play. First off, we have our main unit right here that does all the work. This black box stores right inside here. It comes with all the vacuum lines and wiring and air lines needed to hook up to the rest of the vehicle. This also T's into the factory vacuum line on the vehicle. It comes with a check valve and also a T.
Blue Ox Base Plate Kit Installation - 2006 Jeep Liberty
Today on our 2006 Jeep Liberty, we're going to show you Part Number BX1122. This is the Blue Ox Base Plate Kit with removal arms. This is what the base plate looks like once installed on our vehicle. You notice that it sits in this opening right here that's in part of the bumper cover and it completely fills it up. We have a loop here for our safety cables. This section here is a receiver for the arms that go into place.
Hopkins Tail Light Wiring Kit Installation - 2006 Jeep Liberty
Today on this 2006 Jeep Liberty, we're going to show you part number HM56203. This is the Hopkins Custom Taillight Wiring Kit for Towed Vehicles. This is what we get in the kit. This is our actual wire harness right here and this is actually a T-connector that plugs into the factory wire harness. This one with the green wire will actually go to our passenger's side. This is our converter that contains all our diodes to protect the vehicle from the towed vehicle and here's our T-connector for the driver's side.
Trailer Hitch Installation - 2006 Jeep Liberty - Hidden Hitch
Today on our 2006 Jeep Liberty, we'll be installing Hidden Hitch, Part Number 87006. This is what our hitch to look like once it's installed. Next, we'll give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the rear spare tire is 9-3/4 inches. From the top of the receiver tube opening to the ground is 15-3/4 inches. This will assist you in selecting accessories such as a drawbar, a bike rack or cargo carrier.
Trailer Hitch Installation - 2006 Jeep Liberty - Draw-Tite
Today on our 2006 Jeep Liberty, we'll be installing the Draw-Tite Hitch, Part Number 75128. This is what our hitch to look like once it's installed. Next, we'll go ahead and give you couple measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the rear spare tire is 9-3/4 inches. From the top of the receiver tube opening to the ground is 15-3/4 inches. This will assist you in selecting accessories such as a drawbar, a bike rack or a cargo carrier.
Yakima SpareTime Spare Tire Mount Bike Rack Review - 2006 Jeep Liberty
Today on our 2006 Jeep Liberty, we'll be test fitting the Yakima SpareTime 2 Bike Carrier, part number Y02598. Now, we've already gone ahead and removed our spare tire and we've also removed the center cap out of the spare wheel. We can now place our adapter plate onto the spare tire mount and reinstall our spare tire. With our spare tire tight, we're now ready to load our bike rack. We'll place the bike rack into the wheel mount adapter and tighten it down using the red knob. That will secure our bike rack to the vehicle.
Thule Spare Me Spare Tire Mount Bike Rack Review - 2006 Jeep Liberty
Today on our 2006 Jeep Liberty well be test fitting the Thule Spare Me 2 Bike Carrier Spare Tire Mount, part number TH963XTR. And to begin our test fit well need to remove the spare tire from the vehicle and with the spare tire off well also need to remove the center cap from the spare tire. We can then place the adapter plate onto the spare tire mount and reinstall our spare tire. With our spare tire back tight, we can then place our bike rack up and using the knob well tighten it down. That will secure our bike rack to the vehicle. Well now go ahead and undo the knobs to bring out our dual arms.
SportRack Spare Tire Mount Bike Rack Review - 2006 Jeep Liberty
Today on our 2006 Jeep Liberty, we'll be testing the SportRack 3 Bike Carrier Spare Tire Mount Bike Rack, part number A30813STL. Now, we've already gone ahead and removed our spare tire from the spare tire mount. So next, we'll go ahead and install our bike rack mount. We can then reinstall our spare tire. With our spare tire tight, we're ready to fit our bike rack. We'll slide the bike rack over the spare tire mount and tighten it down with the hand knob.
SportRack Aero Roof Cargo Box Installation - 2006 Jeep Liberty
Today on our 2006 Jeep Liberty, we'll be test fitting the SportRack Aero XL Cargo Box, part number A90275. Now, our vehicle is already equipped with a roof rack system so we're ready to go ahead and fit our cargo box. We'll simply place the box on top of the roof rack, making sure we line up the holes in the floor of the cargo box over the top of our crossbars. We can then use the included hardware to secure our cargo box to the roof rack. And with our hardware all tight, our box is secured to the vehicle and we're ready to load it up. And that completes the test fit of the SportRack Aero XL Cargo Box, part number A90275 on our 2006 Jeep Liberty..
Thule MOAB Roof Top Cargo Basket Review - 2006 Jeep Liberty
Today on our 2006 Jeep Liberty well be test fitting the Thule Moab Rooftop Cargo Carrier part number th690. Now to begin well simply place the Moab on top of our crossbars. Well then center it with the vehicle. We can then take the included hardware and run it underneath our crossbars and secure it using the wing nuts. Well go ahead and install out hardware covers which will complete the test fit. Our basket is secure and were ready to load it up.
Thule AeroBlade Crossroad Roof Rack Installation - 2006 Jeep Liberty
Hollywood Racks SR2 Spare Tire Mount Bike Rack Review - 2006 Jeep Liberty
Today on our 2006 Jeep Liberty well be test fitting the Hollywood Racks sr2 two by Carrier spare tire mount part number hrsr2. Now to begin weve already removed our spare tire from the spare tire mount so now we can install our adapter plate. We can then re-install our spare tire. With our spare tire tight were now ready to load the bike rack. Well slide the bike rack over the spare tire mount and tighten it down using the bolt. We can then install our cover.
Today on our 2005 Jeep liberty well be installing the Tow Ready T1 connector part #: 118524. Our first step, well need to open up the rear cargo door. This will allow us to access the two fasteners on each side securing the taillight assemblies. Starting here on the passenger side well go ahead and remove the two fasteners and then the taillight assembly. Be careful when prying the taillight assembly away from the body of the vehicle not to break the alignment tabs as you can see here. Next well go ahead and remove the manufacturers wiring from the taillight assembly.
Roadmaster Tow Bar Installation - 2006 Jeep Liberty
Today we are going to show you part number RM-576 from Roadmaster. This is their Sterling All Terrain tow bar. We will be installing this on a 2006 Jeep Liberty. Our Jeep here already has the base plates installed so we are going to concentrate on the tow bar. We have got the parts laid out in the order of assembly. Starting off with these two pieces right here, these are the adapter parts that go to your face plate that is mounted on your vehicle which allows you to connect this cross bar to the base plates and then to this cross bar the sterling all terrain tow bar mounts to it. Start with the brackets that are listed for the driver side and passenger side of a car. This will get mounted up like this and then the bracket for the safety chains is going to get mounted on the bottom like this. Go ahead and bolt up these two halves and put the assembly on to the tow bar bracket. 01:00
Roadmaster Tow Bar Wiring Kit Installation - 2006 Jeep Liberty
Today on this 2006 Jeep Liberty we are going to install part number RM-154 from Roadmaster. What this does is allows us to wire up the vehicle so that it can be towed behind an RV. The first step is to route the wire from the front to rear and the wire harness comes with two truck ends on the wiring harness itself. We are just going to cut off one end of it, leave about a foot or so on there in case we need to use it again or in case the original one gets worn out. This 4-pole is going to stay at the front and basically you can think about it as like wiring up a utility trailer. This is going to stay in the front and the car is going to become a trailer at this point. We are going to run our wire between the plastic up in here towards the center as close as possible because in the future a face plate will get installed in that general area. Thread that on through until we come out the other side and we are going to route it all the way back and stay away from the suspension components and we are actually going to run it through the frame. 01:00
Roadmaster Base Plate Installation - 2006 Jeep Liberty
Today, on this 2006 Jeep Liberty, we are going to install part number 521423-1 from Roadmaster. What is going to happen is these base plates mount to the frame of the vehicle and allows the vehicle to be towed behind. The mounts will be approximately right in this area, right here. So to get started we are going to have to remove the bumper cover and the grille. We will go ahead and start off by taking the bolts off the lower part of the fascia here so we can get that loose. We have the bottom part of the fascia loose now. Now let us go to the top and start working on the grille and work our way down to take the fascia off. Alright, next we will go ahead and start taking off the grille. There is basically, on this model, there is a series of snaps that hold the grille in place. So we will undo these first. Next what we are going to do is continue with the bumper cover here and remove this bolt here and here. Next we will go ahead and remove the plastic rivets that go to the fender liner here, one here and one here. Repeat the same process back over on the passenger side. Alright, getting back underneath, there are two more plastic rivets that we need to take out here and here. With the fender wheel liner pulled back a little bit, and then push in. There is a little snap right here. And then pull down. 1:20
Trailer Hitch Installation - 2006 Jeep Liberty
Today we are going to install part number 13044 from Curt, and we are going to install this Class III receiver hitch on a 2006 Jeep Liberty. We will show you where the hitch mounts up. It is going to mount up along three holes in the frame here, here and here. And this has a skid shield in place. Your vehicle may not have the skid shield, so it is going to have the empty three holes. And it is going to be the same thing on the other side. In this case, this actually comes down with a recovery hook that is in place. This whole piece and assembly will actually have to come down and stay off when the hitch is installed. Again, there are three bolts on each side behind this hook, too, just like on the passengers side.
Subscribe to email newsletter
privacy - we don't send unsolicited email
All images, layout and content copyright etrailer.com