1988 Chevrolet Accessories:

Select Model for Your 1988 Chevrolet

1988 Chevrolet Accessories

Towing

1988 Chevrolet Trailer Hitch

1988 Chevrolet Trailer Wiring

1988 Chevrolet Brake Controller

1988 Chevrolet Fifth Wheel Hitch

1988 Chevrolet Gooseneck Hitch

1988 Chevrolet Front Mount Hitch

1988 Chevrolet Towing Mirrors

1988 Chevrolet Base Plate for Tow Bar

Cargo Control

1988 Chevrolet Roof Rack

1988 Chevrolet Tool Box

1988 Chevrolet Ladder Rack

1988 Chevrolet Tailgate

1988 Chevrolet Truck Bed Extender

1988 Chevrolet Trunk Bike Rack

1988 Chevrolet Vehicle Cargo Control

1988 Chevrolet Truck Bed Sliding Tray

Performance Accessories

1988 Chevrolet Air Filter

1988 Chevrolet Exhaust

1988 Chevrolet Suspension Enhancement

1988 Chevrolet Transmission Cooler

1988 Chevrolet Interior Lights

1988 Chevrolet Exterior Lights

1988 Chevrolet Tire Chains

1988 Chevrolet Throttle Body Spacer

1988 Chevrolet Fluid Filters

1988 Chevrolet Vehicle Sway Bars

1988 Chevrolet Vehicle Lightbars

Vehicle Trim

1988 Chevrolet Floor Mats

1988 Chevrolet Tonneau Cover

1988 Chevrolet Tube Steps

1988 Chevrolet Trim Kits

1988 Chevrolet Vehicle Covers

1988 Chevrolet Grille Guard

1988 Chevrolet Bug Shield

1988 Chevrolet Side Window Vents

1988 Chevrolet Truck Bed Mat

1988 Chevrolet Bumpers

1988 Chevrolet Mud Flaps

1988 Chevrolet Lamp Guards

1988 Chevrolet Truck Tailgate Lock

1988 Chevrolet Truck Bed Rail Caps

1988 Chevrolet Vehicle Tent

1988 Chevrolet Vehicle Seat Covers

1988 Chevrolet Replacement Mirrors

1988 Chevrolet Windshield Wiper Blades

1988 Chevrolet Questions and Answers

• Gooseneck Rail Kit and Hitch Recommendation for a 1988 Chevy V30
  
• I spoke to my contact at Curt and he informed me that the only gooseneck option they have for you setup would be to go with a Universal Gooseneck Rail Kit # C61502 and then a Folding Ball Gooseneck Hitch # C-52. I attached installation instructions for both products for you to check out.
  view full answer...


• Dim and Malfunctioning Trailer Lights on a Trailer Towed by a 1988 Chevy C/K Series Truck
  
• This sounds like a weak ground, corroded connector, or both. Make sure that the ground on the 7-Way you installed is attached to a clean and corrosion free bare metal surface. A weak ground could cause this issue. Ground problems normally show up when there is more load on the system like when the running lights are on and you step on the brake. Also make sure the 4-way that you installed is properly grounded. A corroded connector can cause all sorts of weird things to occur as well so check
  view full answer...


• Replacement 2-1/2 Inch Catalytic Converters for a 1988 Chevrolet Camaro Iroc-Z
  
• I checked with my contact at MagnaFlow for catalytic converter options for your 1988 Camaro Iroc-Z. He stated that due to the EPA and CARB regulations in California we cannot recommend that you install a catalytic converter that is different from the 2.25 converter that comes on your vehicle. Modifying your exhaust system would not comply with the laws in California, which is why the shops are trying to sell you the 2.25 converter. They cannot sell a product for a vehicle that does not comply
  view full answer...


• Transmission Cooler for a 1988 Lazy Dave RV on a Chevy G30 Van Chassis
  
• Transmission coolers are not vehicle specific so anyone that will fit in the space you have in the engine compartment you can use. Adding the cooler will not bypass the existing cooler which is located inside the radiator. Adding a cooler provides supplemental cooling to the factory cooler. The traditional way to install an additional cooler is in line with the factory line that leads back to the transmission. You will have one hose that goes from the transmission to the radiator and another
  view full answer...


• Fan Clutches and Radiator Fans for a 1988 Chevy C/K1500 pickup Truck with 5.7 Liter V8
  
• There are a couple of different fan clutches that fit a 1988 Chevy C/K series 1500 depending on the rear axle gear ration and if it has air conditioning. If your truck has a 3.73 or higher rear end or has air conditioning with 3.42 or higher rear end, you will need Derale Thermal Fan Clutch, # D22140. The fan mounting holes will be 10mm. If your truck does not have air conditioning and it has 3.08 or 3.42 rear end, you will need Derale Thermal Fan Clutch, # D22142. You will need a fan
  view full answer...


• Will The Longview Custom Towing Mirrors # CTM1200 Fit My 1988 Chevrolet Astro Van
  
• Yes, as long as your factory mirrors look like the attached image, the Longview Custom Towing Mirrors # CTM1200, will fit your 1988 Chevrolet Astro Van. These mirrors will fit directly over your factory mirrors and are designed to fit the 1986 to 2005 Chevrolet Astro Van and 1988 to 2005 GMC Safari Van.
  view full answer...


• Dimensions for Spring Hanger Spacing Using the # APTT3 Triple-Axle Hanger Kit on a Boat Trailer
  
• The spring hanger mounting dimensions for the Triple-Axle Trailer Hanger Kit, item # APTT3, are as follows. From the center of the hole in the front hanger, to the center of the hole in the center front hanger, the distance should be 29-1/2 inches. From the center of the hole in the center front hanger, to the center of the hole in the center rear hanger, the distance should be 34 inches. And from the center of the hole in the center rear hanger, to the center of the hole in the rear hanger,
  view full answer...


• Weight Distribution with Sway Control Recommendation, 1998 Chevy Astro Towing 3,000 Pound Trailer
  
• If your 1998 Chevy Astro has a 2 inch trailer hitch receiver rated for use with weight distribution, then you will be able to use a weight distribution system. To choose the correct sized system, you will need one that has a tongue weight capacity range that encompasses your trailer tongue weight loaded and ready to tow. Trailer tongue weight should be between 10 and 15 percent of the gross trailer weight. Going by the 3,000 pound weight you have provided, I recommend a system with a range of
  view full answer...


• Installing a Reese 16 K Fifth Wheel Hitch on a 1988 Chevy Pickup
  
• If you are using the universal install kit, part # RP30035, the hitch would be installed so that the king pin is approx. 1 1/2 inches in front of the rear axle center. Below is a copy of the installation instructions.
  view full answer...