1987 Chevrolet Accessories:

Select Model for Your 1987 Chevrolet

1987 Chevrolet Accessories

Towing

1987 Chevrolet Trailer Hitch

1987 Chevrolet Trailer Wiring

1987 Chevrolet Brake Controller

1987 Chevrolet Fifth Wheel Hitch

1987 Chevrolet Towing Mirrors

1987 Chevrolet Base Plate for Tow Bar

Cargo Control

1987 Chevrolet Roof Rack

1987 Chevrolet Tool Box

1987 Chevrolet Ladder Rack

1987 Chevrolet Truck Bed Extender

1987 Chevrolet Trunk Bike Rack

1987 Chevrolet Truck Bed Sliding Tray

Performance Accessories

1987 Chevrolet Air Filter

1987 Chevrolet Exhaust

1987 Chevrolet Suspension Enhancement

1987 Chevrolet Transmission Cooler

1987 Chevrolet Exterior Lights

1987 Chevrolet Throttle Body Spacer

1987 Chevrolet Fluid Filters

1987 Chevrolet Vehicle Sway Bars

1987 Chevrolet Vehicle Lightbars

Vehicle Trim

1987 Chevrolet Floor Mats

1987 Chevrolet Tonneau Cover

1987 Chevrolet Tube Steps

1987 Chevrolet Trim Kits

1987 Chevrolet Vehicle Covers

1987 Chevrolet Bug Shield

1987 Chevrolet Side Window Vents

1987 Chevrolet Bumpers

1987 Chevrolet Mud Flaps

1987 Chevrolet Truck Bed Rail Caps

1987 Chevrolet Vehicle Tent

1987 Chevrolet Vehicle Seat Covers

1987 Chevrolet Replacement Mirrors

1987 Chevrolet Windshield Wiper Blades

1987 Chevrolet Questions and Answers

• Will Hidden Hitch Class III Trailer Hitch Receiver, Part # 87034, Fit on 1987 Chevy C-10 Pickup
  
• The Hidden Hitch Class III Trailer Hitch Receiver, part # 87034, will fit your 1987 Chevy C-10 pickup. This hitch works with both 6-foot and 8-foot beds and with both standard and step bumpers. (If your truck has a deep-drop bumper you would instead use hitch # 87480; please see the attached illustration of a deep-drop bumper.) This hitch receiver will provide a 2 x 2 inch square receiver opening for a draw bar and hitch ball (used for towing), or for any hitch-mounted accessory items such a
  view full answer...


• Trailer Hitch Recommendation for a 1987 Chevy C/K 1500 With a Deep Drop Bumper
  
• A deep drop bumper is a bumper that hangs further below the frame than a standard bumper. Check out the photo that I attached showing a deep drop bumper compared to a standard bumper and a step bumper. We have three frame mount trailer hitches that will work with a deep drop bumper on your 1987 Chevrolet C/K 1500. You could install the Curt Hitch, # C13099, the Hidden Hitch, # 87480, or the Draw-Tite Hitch, # 41504. These are all Class III trailer hitches that have a towing capacity of 5,000
  view full answer...


• Trailer Hitch and Accessory Recommendations for a 1987 Chevy Suburban 1500
  
• We only carry 1 trailer hitch for the 1987 Chevy Suburban, # 75500. The Ultra-Frame hitch, # 41901, fits Chevy and GMC trucks but not the Suburban. The 75500 hitch can handle up to 7,500 pound gross trailer weight and 750 pounds tongue weight when used with weight distribution. I have included a link to the installation instructions for you. If you plan on doing some towing, I recommend the etrailer ball mount kit # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip, and
  view full answer...


• What Parts are Needed to Install an Electric Trailer Brake Controller on a 1987 Chevy Astro
  
• In order to install a brake controller on a 1987 Chevy Astro, there are a few parts you are going to need. First, you need to install a 4-Way trailer wiring harness, # 18252. I have included a link to a video that shows a typical installation. You will need to use the included circuit tester to test the van wiring because it will most likely not match color for color with the vehicle in the video. After you have installed the 4-Way, you will need to install a 4 and 7 Way installation kit, # E
  view full answer...


• Hitch Recommendation for 1987 Chevrolet Silverado
  
• For your 1987 Chevrolet Silverado The Draw-Tite Trailer Hitch for the Chevrolet C/K Series Pickup, 1987 part # 40050 allows you to retain the stock spare tire location. Removing the tire temporarily for this install is optional. However, it is recommended and it will make the install easier to complete. Once the install is complete the spare tire can be returned to its original location.
  view full answer...


• Weight Distribution / Sway Control System That Will Fit A V-Nose Trailer
  
• Yes, the Strait-Line Weight Distribution Hitch System can be adapted to a V-Nose style trailer. You would need to use an alternate mounting system for the chain hanger brackets. The Bolt on Chain Hanger Kit, item # RP58305, will bolt onto the side of trailer frame. Once installed the chains are attached by raising the trailer tongue and rear of vehicle with the trailer jack. Tubular frames cannot be wider than 2-1/4 inches with this hanger kit, so you will need to be sure and measure before purc
  view full answer...